- Page 1: Via Leonardo Da Vinci, 36 - 20040 R
- Page 5 and 6: K-FLEX IC CLAD is a flexible closed
- Page 9 and 10: NO SI K-FLEX IC CLAD Practical sugg
- Page 11 and 12: K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 13 and 14: For procedure details reletive to t
- Page 15 and 16: Laying of the two consecutive K-FLE
- Page 17 and 18: +5 cm Circumference of the insulate
- Page 19 and 20: A) Place sheet II in a way to overl
- Page 21 and 22: Preparation of a length of tube A)
- Page 23 and 24: A) Glue the overlap with K 420 adhe
- Page 25 and 26: Laying of tube II B C K-FLEX IC CLA
- Page 27 and 28: A) Glue with K 420 adhesive the lon
- Page 29 and 30: A) The finishing of the product is
- Page 31 and 32: A With the same procedure illustrat
- Page 33 and 34: K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 35 and 36: For procedure details reletive to t
- Page 37 and 38: Laying of the two consecutive K-FLE
- Page 39 and 40: +5 cm Circumference of the insulate
- Page 41 and 42: A) Place sheet II in a way to overl
- Page 43 and 44: Preparation of a length of tube A)
- Page 45 and 46: A) Glue the overlap with K 420 adhe
- Page 47 and 48: Laying of tube II B C K-FLEX IC CLA
- Page 49 and 50: A) Glue with K 420 adhesive the lon
- Page 51 and 52: A) The finishing of the product is
- Page 53 and 54:
A With the same procedure illustrat
- Page 55 and 56:
K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 57 and 58:
For the application procedures of K
- Page 59 and 60:
How to arrange the finishing shapes
- Page 61 and 62:
How to fix the joints of the IC CLA
- Page 63 and 64:
How to fix the joints of the IC CLA
- Page 65 and 66:
A) Remove the protective silicone p
- Page 67 and 68:
K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 69 and 70:
K-FLEX IC CLAD - “T-piece” insu
- Page 71 and 72:
K-FLEX IC CLAD - “T-piece” “T
- Page 73 and 74:
K-FLEX IC CLAD - “T-piece” “T
- Page 75 and 76:
A K-FLEX IC CLAD - “T-piece”
- Page 77 and 78:
The pre-shaped and pre-cut “T-pie
- Page 79 and 80:
F) Glue the elastomer edges with co
- Page 81 and 82:
L) Remove protective silicone paper
- Page 83 and 84:
IC CLAD Application guide 04/04 - E
- Page 85 and 86:
INDEX Flanges: Insulation and finis
- Page 87 and 88:
Finishing of adjacent tubes • Pre
- Page 89 and 90:
Finishing of the flange body B) Cut
- Page 91 and 92:
A) Cut a section of K-FLEX IC / IN
- Page 93 and 94:
G) Prepare a strip of IC / IN CLAD
- Page 95 and 96:
D) Fix with the specific IC CLAD ad
- Page 97 and 98:
K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 99 and 100:
For the detailed preparation of the
- Page 101 and 102:
• Cut out a ring, the diameter of
- Page 103 and 104:
K-FLEX IC CLAD - VALVES Finishing o
- Page 105 and 106:
• Measure the indicated diameters
- Page 107 and 108:
K-FLEX IC CLAD - VALVES Valve finis
- Page 109 and 110:
K-FLEX IC CLAD - VALVES Valve finis
- Page 111 and 112:
1) Cut out the covering of the valv
- Page 113 and 114:
K-FLEX IC CLAD - VALVES Finishing o
- Page 115 and 116:
K-FLEX IC CLAD - VALVES Finishing o
- Page 117 and 118:
K-FLEX IC CLAD - VALVES Finishing o
- Page 119 and 120:
The pre-shaped K-FLEX IC CLAD valve
- Page 121 and 122:
• Fix all the joints, including t
- Page 123 and 124:
INDEX Reducers: insulation and fini
- Page 125 and 126:
3 2 1 K-FLEX IC CLAD Finishing of r
- Page 127 and 128:
K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 129 and 130:
For the detailed installation of K-
- Page 131 and 132:
1 2 K-FLEX IC CLAD - SMALL AND MEDI
- Page 133 and 134:
Finishing of the accessory parts
- Page 135 and 136:
As previously illustrated for the b
- Page 137 and 138:
INDEX Large tanks: insulation and f
- Page 139 and 140:
Insulation of the tank’s wall K-F
- Page 141 and 142:
Finishing of the tank’s wall •
- Page 143 and 144:
Finishing of the tank’s roof K-FL
- Page 145 and 146:
If necessary, accurately seal the e
- Page 147 and 148:
Covering the wall of the tank For t
- Page 149 and 150:
Covering of the tank’s wall • T
- Page 151 and 152:
Covering the top of the tank’s ro
- Page 153 and 154:
Preparation of the internal coverin
Change language