Application Manual K-FLEX IC-CLAD 1109.pdf

More documents

Recommendations

Info

Finishing of the top of the wall • On the top of the wall an indentated ring of IC CLAD sheet must be applied to protect the angle with the roof of the tank B). A • Apply the sections of IC CLAD sheet correctly joined by overlapping edges a), to which an indentation will be made, folded at 90° above the level of the roof. Glue them with K 420 adhesive and fix the joints with IC CLAD adhesive tape. a K-FLEX IC CLAD - LARGE TANKS Finishing with IC CLAD sheet KEY: K 420 adhesive Marine silicone Measurements Actions B • Calculate the number of IC CLAD sheet sections that will be used to complete the circumference of the tank (C). C IC CLAD Application guide 04/04 - Engl. IC CLAD - LARGE TANKS 07 9
Finishing of the tank’s roof K-FLEX IC CLAD - LARGE TANKS Finishing with IC CLAD sheet For the finishing to apply onto the roof, cover each K-FLEX elastomeric sheet, already previously placed, with sections of IC CLAD sheet. The example shown illustrates starting the covering from the circular area a) continuing gradually with the internal areas proceeding towards the center, rispecting a criteria of overlapping the joints in an orderly and functional manner to allow the water to flow from the center of the roof towards the edges of the tank b). • For the finishing of the tank’s roof retrace the pattern of the elastomeric sheets already in place.Take the measurements of the elastomeric sheet and cut the section of the corresponding IC CLAD sheet , leaving the correct abundaces for the overlapping (a). •First place the outer sheet sections and then gradually proceed towards the center of the roof, overlapping each sheet to those placed before. In this way even the slight difference in level of the overlappings will allow the water to flow towards the outside ( ). • Glue the joints with K 420 adhesive and fix them with the specific IC CLAD adhesive tape. KEY: K 420 adhesive Marine silicone Measurements Actions IC CLAD Application guide 04/04 - Engl. IC CLAD - LARGE TANKS 9 08
Page 1 and 2:
Via Leonardo Da Vinci, 36 - 20040 R
Page 3 and 4:
K-FLEX IN CLAD APPLICATION GUIDE IN
Page 5 and 6:
K-FLEX IC CLAD is a flexible closed
Page 9 and 10:
NO SI K-FLEX IC CLAD Practical sugg
Page 11 and 12:
K-FLEX IC CLAD APPLICATION GUIDE IN
Page 13 and 14:
For procedure details reletive to t
Page 15 and 16:
Laying of the two consecutive K-FLE
Page 17 and 18:
+5 cm Circumference of the insulate
Page 19 and 20:
A) Place sheet II in a way to overl
Page 21 and 22:
Preparation of a length of tube A)
Page 23 and 24:
A) Glue the overlap with K 420 adhe
Page 25 and 26:
Laying of tube II B C K-FLEX IC CLA
Page 27 and 28:
A) Glue with K 420 adhesive the lon
Page 29 and 30:
A) The finishing of the product is
Page 31 and 32:
A With the same procedure illustrat
Page 33 and 34:
Page 35 and 36:
For procedure details reletive to t
Page 37 and 38:
Laying of the two consecutive K-FLE
Page 39 and 40:
+5 cm Circumference of the insulate
Page 41 and 42:
A) Place sheet II in a way to overl
Page 43 and 44:
Preparation of a length of tube A)
Page 45 and 46:
A) Glue the overlap with K 420 adhe
Page 47 and 48:
Laying of tube II B C K-FLEX IC CLA
Page 49 and 50:
A) Glue with K 420 adhesive the lon
Page 51 and 52:
A) The finishing of the product is
Page 53 and 54:
A With the same procedure illustrat
Page 55 and 56:
Page 57 and 58:
For the application procedures of K
Page 59 and 60:
How to arrange the finishing shapes
Page 61 and 62:
How to fix the joints of the IC CLA
Page 63 and 64:
How to fix the joints of the IC CLA
Page 65 and 66:
A) Remove the protective silicone p
Page 67 and 68:
Page 69 and 70:
K-FLEX IC CLAD - “T-piece” insu
Page 71 and 72:
K-FLEX IC CLAD - “T-piece” “T
Page 73 and 74:
K-FLEX IC CLAD - “T-piece” “T
Page 75 and 76:
A K-FLEX IC CLAD - “T-piece”
Page 77 and 78:
The pre-shaped and pre-cut “T-pie
Page 79 and 80:
F) Glue the elastomer edges with co
Page 81 and 82:
L) Remove protective silicone paper
Page 83 and 84:
IC CLAD Application guide 04/04 - E
Page 85 and 86:
INDEX Flanges: Insulation and finis
Page 87 and 88:
Finishing of adjacent tubes • Pre
Page 89 and 90:
Finishing of the flange body B) Cut
Page 91 and 92: A) Cut a section of K-FLEX IC / IN
Page 93 and 94: G) Prepare a strip of IC / IN CLAD
Page 95 and 96: D) Fix with the specific IC CLAD ad
Page 97 and 98: K-FLEX IC CLAD APPLICATION GUIDE IN
Page 99 and 100: For the detailed preparation of the
Page 101 and 102: • Cut out a ring, the diameter of
Page 103 and 104: K-FLEX IC CLAD - VALVES Finishing o
Page 105 and 106: • Measure the indicated diameters
Page 107 and 108: K-FLEX IC CLAD - VALVES Valve finis
Page 109 and 110: K-FLEX IC CLAD - VALVES Valve finis
Page 111 and 112: 1) Cut out the covering of the valv
Page 119 and 120: The pre-shaped K-FLEX IC CLAD valve
Page 121 and 122: • Fix all the joints, including t
Page 123 and 124: INDEX Reducers: insulation and fini
Page 125 and 126: 3 2 1 K-FLEX IC CLAD Finishing of r
Page 127 and 128: K-FLEX IC CLAD APPLICATION GUIDE IN
Page 129 and 130: For the detailed installation of K-
Page 131 and 132: 1 2 K-FLEX IC CLAD - SMALL AND MEDI
Page 133 and 134: Finishing of the accessory parts
Page 135 and 136: As previously illustrated for the b
Page 137 and 138: INDEX Large tanks: insulation and f
Page 139 and 140: Insulation of the tank’s wall K-F
Page 141: Finishing of the tank’s wall •
Page 145 and 146: If necessary, accurately seal the e
Page 147 and 148: Covering the wall of the tank For t
Page 149 and 150: Covering of the tank’s wall • T
Page 151 and 152: Covering the top of the tank’s ro
Page 153 and 154: Preparation of the internal coverin
show all

Application Manual K-FLEX IC-CLAD 1109.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?