Application Manual K-FLEX IC-CLAD 1109.pdf

More documents

Recommendations

Info

• Remove the protective silicone paper of the adhesive overlaps and fix the closure of the finishing parts. K-FLEX IC CLAD - VALVES Finishing with pre-shaped valve covered with IC CLAD sheet KEY: K 420 adhesive Marine silicone Measurements Actions IC CLAD Application guide 04/04 - Engl. IC CLAD - VALVES 24 6
• Fix all the joints, including those of the pre-shaped part, with the specific IC CLAD adhesive tape (1). K-FLEX IC CLAD - VALVES Finishing with pre-shaped valve covered with IC CLAD sheet 1 2 KEY: K 420 adhesive Marine silicone Measurements Actions • For external applications, if necessary, seal the edges of the tapes with marine silicone. (2). IC CLAD Application guide 04/04 - Engl. IC CLAD - VALVES 25 6
Page 1 and 2:
Via Leonardo Da Vinci, 36 - 20040 R
Page 3 and 4:
K-FLEX IN CLAD APPLICATION GUIDE IN
Page 5 and 6:
K-FLEX IC CLAD is a flexible closed
Page 9 and 10:
NO SI K-FLEX IC CLAD Practical sugg
Page 11 and 12:
K-FLEX IC CLAD APPLICATION GUIDE IN
Page 13 and 14:
For procedure details reletive to t
Page 15 and 16:
Laying of the two consecutive K-FLE
Page 17 and 18:
+5 cm Circumference of the insulate
Page 19 and 20:
A) Place sheet II in a way to overl
Page 21 and 22:
Preparation of a length of tube A)
Page 23 and 24:
A) Glue the overlap with K 420 adhe
Page 25 and 26:
Laying of tube II B C K-FLEX IC CLA
Page 27 and 28:
A) Glue with K 420 adhesive the lon
Page 29 and 30:
A) The finishing of the product is
Page 31 and 32:
A With the same procedure illustrat
Page 33 and 34:
Page 35 and 36:
For procedure details reletive to t
Page 37 and 38:
Laying of the two consecutive K-FLE
Page 39 and 40:
+5 cm Circumference of the insulate
Page 41 and 42:
A) Place sheet II in a way to overl
Page 43 and 44:
Preparation of a length of tube A)
Page 45 and 46:
A) Glue the overlap with K 420 adhe
Page 47 and 48:
Laying of tube II B C K-FLEX IC CLA
Page 49 and 50:
A) Glue with K 420 adhesive the lon
Page 51 and 52:
A) The finishing of the product is
Page 53 and 54:
A With the same procedure illustrat
Page 55 and 56:
Page 57 and 58:
For the application procedures of K
Page 59 and 60:
How to arrange the finishing shapes
Page 61 and 62:
How to fix the joints of the IC CLA
Page 63 and 64:
How to fix the joints of the IC CLA
Page 65 and 66:
A) Remove the protective silicone p
Page 67 and 68:
Page 69 and 70: K-FLEX IC CLAD - “T-piece” insu
Page 71 and 72: K-FLEX IC CLAD - “T-piece” “T
Page 73 and 74: K-FLEX IC CLAD - “T-piece” “T
Page 75 and 76: A K-FLEX IC CLAD - “T-piece”
Page 77 and 78: The pre-shaped and pre-cut “T-pie
Page 79 and 80: F) Glue the elastomer edges with co
Page 81 and 82: L) Remove protective silicone paper
Page 83 and 84: IC CLAD Application guide 04/04 - E
Page 85 and 86: INDEX Flanges: Insulation and finis
Page 87 and 88: Finishing of adjacent tubes • Pre
Page 89 and 90: Finishing of the flange body B) Cut
Page 91 and 92: A) Cut a section of K-FLEX IC / IN
Page 93 and 94: G) Prepare a strip of IC / IN CLAD
Page 95 and 96: D) Fix with the specific IC CLAD ad
Page 97 and 98: K-FLEX IC CLAD APPLICATION GUIDE IN
Page 99 and 100: For the detailed preparation of the
Page 101 and 102: • Cut out a ring, the diameter of
Page 103 and 104: K-FLEX IC CLAD - VALVES Finishing o
Page 105 and 106: • Measure the indicated diameters
Page 107 and 108: K-FLEX IC CLAD - VALVES Valve finis
Page 109 and 110: K-FLEX IC CLAD - VALVES Valve finis
Page 111 and 112: 1) Cut out the covering of the valv
Page 119: The pre-shaped K-FLEX IC CLAD valve
Page 123 and 124: INDEX Reducers: insulation and fini
Page 125 and 126: 3 2 1 K-FLEX IC CLAD Finishing of r
Page 127 and 128: K-FLEX IC CLAD APPLICATION GUIDE IN
Page 129 and 130: For the detailed installation of K-
Page 131 and 132: 1 2 K-FLEX IC CLAD - SMALL AND MEDI
Page 133 and 134: Finishing of the accessory parts
Page 135 and 136: As previously illustrated for the b
Page 137 and 138: INDEX Large tanks: insulation and f
Page 139 and 140: Insulation of the tank’s wall K-F
Page 141 and 142: Finishing of the tank’s wall •
Page 143 and 144: Finishing of the tank’s roof K-FL
Page 145 and 146: If necessary, accurately seal the e
Page 147 and 148: Covering the wall of the tank For t
Page 149 and 150: Covering of the tank’s wall • T
Page 151 and 152: Covering the top of the tank’s ro
Page 153 and 154: Preparation of the internal coverin
show all

Application Manual K-FLEX IC-CLAD 1109.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?