- Page 1 and 2:
Via Leonardo Da Vinci, 36 - 20040 R
- Page 3 and 4:
K-FLEX IN CLAD APPLICATION GUIDE IN
- Page 5 and 6:
K-FLEX IC CLAD is a flexible closed
- Page 9 and 10:
NO SI K-FLEX IC CLAD Practical sugg
- Page 11 and 12:
K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 13 and 14:
For procedure details reletive to t
- Page 15 and 16:
Laying of the two consecutive K-FLE
- Page 17 and 18:
+5 cm Circumference of the insulate
- Page 19 and 20:
A) Place sheet II in a way to overl
- Page 21 and 22:
Preparation of a length of tube A)
- Page 23 and 24:
A) Glue the overlap with K 420 adhe
- Page 25 and 26:
Laying of tube II B C K-FLEX IC CLA
- Page 27 and 28:
A) Glue with K 420 adhesive the lon
- Page 29 and 30:
A) The finishing of the product is
- Page 31 and 32:
A With the same procedure illustrat
- Page 33 and 34:
K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 35 and 36:
For procedure details reletive to t
- Page 37 and 38:
Laying of the two consecutive K-FLE
- Page 39 and 40:
+5 cm Circumference of the insulate
- Page 41 and 42:
A) Place sheet II in a way to overl
- Page 43 and 44:
Preparation of a length of tube A)
- Page 45 and 46:
A) Glue the overlap with K 420 adhe
- Page 47 and 48:
Laying of tube II B C K-FLEX IC CLA
- Page 49 and 50:
A) Glue with K 420 adhesive the lon
- Page 51 and 52:
A) The finishing of the product is
- Page 53 and 54:
A With the same procedure illustrat
- Page 55 and 56:
K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 57 and 58:
For the application procedures of K
- Page 59 and 60:
How to arrange the finishing shapes
- Page 61 and 62:
How to fix the joints of the IC CLA
- Page 63 and 64:
How to fix the joints of the IC CLA
- Page 65 and 66:
A) Remove the protective silicone p
- Page 67 and 68:
K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 69 and 70: K-FLEX IC CLAD - “T-piece” insu
- Page 71 and 72: K-FLEX IC CLAD - “T-piece” “T
- Page 73 and 74: K-FLEX IC CLAD - “T-piece” “T
- Page 75 and 76: A K-FLEX IC CLAD - “T-piece”
- Page 77 and 78: The pre-shaped and pre-cut “T-pie
- Page 79 and 80: F) Glue the elastomer edges with co
- Page 81 and 82: L) Remove protective silicone paper
- Page 83 and 84: IC CLAD Application guide 04/04 - E
- Page 85 and 86: INDEX Flanges: Insulation and finis
- Page 87 and 88: Finishing of adjacent tubes • Pre
- Page 89 and 90: Finishing of the flange body B) Cut
- Page 91 and 92: A) Cut a section of K-FLEX IC / IN
- Page 93 and 94: G) Prepare a strip of IC / IN CLAD
- Page 95 and 96: D) Fix with the specific IC CLAD ad
- Page 97 and 98: K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 99 and 100: For the detailed preparation of the
- Page 101 and 102: • Cut out a ring, the diameter of
- Page 103 and 104: K-FLEX IC CLAD - VALVES Finishing o
- Page 105 and 106: • Measure the indicated diameters
- Page 107 and 108: K-FLEX IC CLAD - VALVES Valve finis
- Page 109 and 110: K-FLEX IC CLAD - VALVES Valve finis
- Page 111 and 112: 1) Cut out the covering of the valv
- Page 113 and 114: K-FLEX IC CLAD - VALVES Finishing o
- Page 115 and 116: K-FLEX IC CLAD - VALVES Finishing o
- Page 117 and 118: K-FLEX IC CLAD - VALVES Finishing o
- Page 119: The pre-shaped K-FLEX IC CLAD valve
- Page 123 and 124: INDEX Reducers: insulation and fini
- Page 125 and 126: 3 2 1 K-FLEX IC CLAD Finishing of r
- Page 127 and 128: K-FLEX IC CLAD APPLICATION GUIDE IN
- Page 129 and 130: For the detailed installation of K-
- Page 131 and 132: 1 2 K-FLEX IC CLAD - SMALL AND MEDI
- Page 133 and 134: Finishing of the accessory parts
- Page 135 and 136: As previously illustrated for the b
- Page 137 and 138: INDEX Large tanks: insulation and f
- Page 139 and 140: Insulation of the tank’s wall K-F
- Page 141 and 142: Finishing of the tank’s wall •
- Page 143 and 144: Finishing of the tank’s roof K-FL
- Page 145 and 146: If necessary, accurately seal the e
- Page 147 and 148: Covering the wall of the tank For t
- Page 149 and 150: Covering of the tank’s wall • T
- Page 151 and 152: Covering the top of the tank’s ro
- Page 153 and 154: Preparation of the internal coverin
Change language