Total Access 1500 Single 4-Wire ETO Access Module ... - Adtran

More documents

Recommendations

Info

Compliance Table 2 shows the Compliance Codes for the 4W ETO. The 4W ETO is NRTL listed to the applicable UL standards. The 4W ETO is to be installed in a restricted access location and in a Type “B” or “E” enclosure only. The Total Access 1500 chassis Frame Ground terminal must be connected to an earth ground to ensure that the front panel of the 4W ETO is properly grounded via the backplane connector. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by ADTRAN could void the user’s authority to operate this equipment. 3. INSTALLATION Table 2. Compliance Codes Code Input Output Power Code (PC) F C Telecommunication Code (TC) – X Installation Code (IC) A – C A U T I O N ! SUBJECT TO ELECTROSTATIC DAMAGE OR DECREASE IN RELIABILITY. HANDLING PRECAUTIONS REQUIRED. After unpacking the Total Access 1500 4W ETO, inspect it for damage. If damage has occurred, file a claim with the carrier, then contact ADTRAN Customer Service. Refer to the Warranty and Customer Service section for further information. If possible, keep the original shipping container for returning the 4W ETO for repair or for verification of shipping damage. Shipping Contents The contents include the following items: • 4W ETO • 4W ETO Installation and Maintenance Practice CAUTION Electronic modules can be damaged by ESD. When handling modules, wear an antistatic discharge wrist strap to prevent damage to electronic components. Place modules in antistatic packing material when transporting or storing. When working on modules, always place them on an approved antistatic mat that is electrically grounded. Instructions for Installing the Module The 4W ETO inserts into any access module slot (1 through 24) of a Total Access 1500 chassis. To install the 4W ETO, perform the following steps: 1. If present, remove the Access Module Blank (P/N 1175099L1) from the appropriate access module slot of the Total Access 1500 chassis. 2. Hold the unit by the front panel while supporting the bottom side with the ejector latch, located on the lower left-hand side of the module, at the bottom and opened to engage the chassis edge when it is plugged in. 3. Align the module edges to fit in the lower and upper guide grooves for the designated slot. 4. Slide the module into the access module slot while pressing equally on the top and bottom of the front panel until the module is firmly positioned against the backplane of the chassis. 5. Lock the module in place by pushing in on the ejector latch. The 4W ETO initializes and goes operational upon insertion into an active Total Access 1500 chassis. Initialization is indicated by the front panel LED. Front Panel LED The Total Access 1500 4W ETO has one front panel LED that provides status information. See Table 3 for LED indications. Table 3. Front Panel LED Status Description Green Port is in normal operation Yellow Menu controlled test is in progress Red Port failure has been detected Red (Flashing) Hardware failure has been detected 4 Issue 1, October 2003 61180113L2-5A
4. PROVISIONING There are no hardware options in the 4W ETO access module; its specific options can be provisioned from the SCU ADMIN port or remote craft interface. The factory default settings for the 4W ETO access module are noted in bold text in Table 4 and Table 5. Table 4. 4W ETO General Options Function Option Description Transmit TLP –18.0 to +7.5 dBm (+0.0) Sets the transmit channel attenuation in 0.1 dBm increments from the customer to the network. Receive TLP: 150 and 600 ohms 1200 ohms Sealing Current Mode None Sink Source Tx Termination (1) 150 ohms 600 ohms 1200 ohms Rx Termination (1) 150 ohms 600 ohms 1200 ohms Equalizer Options Height Bandwidth Slope Cable Type –18.0 to +7.5 dBm (+0.0) –20.0 to +5.5 dBm (+0.0) Sets the receive channel attenuation, in 0.1 dBm increments from the network to the customer. Sets the sealing current mode of operation. Selects the impedance of the Transmit T/R pair from the customer toward the T1 network. Selects the impedance of the T1/R1 pair toward the customer. See Table 5 for detailed descriptions of the equalizer provisioning options. Note: Defaults are in bold type. (1) Although no restrictions are placed on the termination settings relative to the equalizer settings, the following configurations are typical: 600 ohms and 1200 ohms impedances can be used in conjunction with active equalization. The 150 ohms and 600 ohms impedances can be used with mismatched equalization. The 600 ohms impedance can also be used on short nonloaded loops where no equalization is necessary. Table 5. 4W ETO Equalizer Options Function Option Description Height 0 to 15 In conjunction with Bandwidth Equalization, corrects for frequency response degradation at the high end of the voice range due to cable length by increasing the 3250-Hz equalization bump. Bandwidth 0 to 15 In conjunction with Height Equalization, corrects for frequency response degradation at the high end of the voice range due to cable length by increasing the breadth of the equalization bump. Slope 0 to 15 Corrects for frequency response degradation at the low end of the voice range due to cable length. Cable Type Non-Loaded Loaded Used to specify loaded or nonloaded cable. This option modifies the equalization circuitry to provide greater gain at the higher frequencies when transmitting over nonloaded cable. 61180113L2-5A Issue 1, October 2003 5
Page 1 and 2: Total Access 1500 Single 4-Wire ETO
Page 3: Physical Slot Table 1. Time Slot an
Page 7 and 8: 5. TEST FEATURES The 4-Wire ETO sup

Total Access 1500 Single 4-Wire ETO Access Module ... - Adtran

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?