We take pleasure in introducing ourselves - Automobile Training ...
We take pleasure in introducing ourselves - Automobile Training ... We take pleasure in introducing ourselves - Automobile Training ...
Model No. MT-Z10 TWO POST LIFT 1. Capacity : 3.5 Tons 2. Electro Hydraulic Symmetrical Supporting Column 3. Passage Width : 2486 mm 4. Lifting Height: 1950 mm 5. Power Supply :Three Phase or Option of Single phase also Model No. MT-Z11 FOUR POST LIST SUITABLE FOR WHEEL ALIGNMENT WITH BUILT IN WHEELS FREE LIFT 1. Capacity : 3500 Kg 2. Motor Capacity : 2.6 KW Model No. MT-Z12 GAS ANALYSER (BLACK BOX VERSION) Model No. MT-Z13 SMOKEMETER 1. Peak and Average Smoke density measurements 2. Measures in KM-1,HSU,FSN and mg/m³ 3. Free or Steady state operation use 4. Rapid Warmup time and self zeroing facility 5. Integral DOT Matrix printer as standard supply 6. Optional Trolley 1. Measures CO,HC,CO2,O2 2. Engine RPM for Sealed engines 3. Oil Temperature measurement 4. Air Fuel Ratio and Lambda Measurements 5. Option to add Nox measurement facility 6. OMIL Class1 category 7. RS 232 Port PAGE 56
Model No. MT-Z14 MULTISCAN FOR PETROL / DIESEL VEHICLES 1. Complete Worldwide Coverage 2. Upgradation through Internet 3. Big Capacity 128MB with software's for Japanese, Korean, Indian Vehicles 4. DTC, Live Reading, Actuation tests and Keycoding 5. Connector locations, Wiring Diagrams and help menus 6. Real-time PC interface through USB port Model No. MT-Z15 PAINTBOOTH Model No. MT-Z16 AC SERVICE STATION 1. Functions: Vacuum,Recharging,Refrigerant purifying and recycling 2. Discharge used Oil and Refill new Oil 3. High Pressure and Low pressure Alarm 4. Empty tank alarm 1. Positive Pressure Paint Booth 2. Size :L x W x H = 6800 x 3800 x 2400 mm 3. Double walled with Insulation 4. With Metal Base with three stage filtration unit 5. Diesel fired Burner, 1,00,000 K cal / hr 6. 7.5 HP, 16000 m³/hr 1440 rpm Air Inlet Blower PAGE 57
- Page 5 and 6: CUT SECTION COMPLETE CHASSIS WITH E
- Page 7 and 8: CUT SECTION COMPLETE CHASSIS WITHOU
- Page 9 and 10: C Model No.MT-C00 MODEL OF CUT SECT
- Page 11 and 12: Model No. Description MT-D01 CUT-SE
- Page 13 and 14: F Model No.MT-F01 CUT SECTION MODEL
- Page 15 and 16: Model No. MT-G06 CUT SECTION MODEL
- Page 17 and 18: H Model No.MT-H00 CUT SECTION MODEL
- Page 19 and 20: Model NO. MT-H15. TRAINING PLATFORM
- Page 21 and 22: Model No.MT-J02 CUT SECTION MODEL O
- Page 23 and 24: Model No. MT-K05 CUT SECTION MODEL
- Page 25 and 26: Model No. MT-L02 CUT SECTION MODEL
- Page 27 and 28: Model No. MT-L07 DEMONSTRATION BOAR
- Page 29 and 30: Model No. MT-L13 DEMONSTRATION BOAR
- Page 31 and 32: N Model No. MT-N01. CUT SECTION MOD
- Page 33 and 34: Model No. MT-N07. CUT SECTION MODEL
- Page 35 and 36: Model No. Description MT-P01 Self s
- Page 37 and 38: R Model No. MT-R00 FOUR STROKE PETR
- Page 39 and 40: Model No. Description MT-T01 Ambass
- Page 41 and 42: 3. Detection terminals for operator
- Page 43 and 44: Model No. MT-X02 INSTRUCTION BOARD
- Page 45 and 46: 8. Set the line break, grounding sh
- Page 47 and 48: 1. Real and operatable starting sys
- Page 49 and 50: COMPUTERIZED MODULE Parameters meas
- Page 51 and 52: Model No. MT-Y04 FOUR STROKE SINGLE
- Page 53 and 54: Z TOOLS AND EQUIPMENTS Model No. MT
- Page 55: Model No. MT-Z07 LOW RAISE LIFT Lif
- Page 59 and 60: Model No. MT-Z21 GLOW PLUG TESTER T
- Page 61 and 62: Model No. MT-Z29 SPOT WELDING Syner
- Page 63 and 64: Model No. MT-Z36 CAR WASHER Single
- Page 65 and 66: Note: we can also supply any other
Model No. MT-Z10<br />
TWO POST LIFT<br />
1. Capacity : 3.5 Tons<br />
2. Electro Hydraulic Symmetrical Support<strong>in</strong>g Column<br />
3. Passage Width : 2486 mm<br />
4. Lift<strong>in</strong>g Height: 1950 mm<br />
5. Power Supply :Three Phase or Option of S<strong>in</strong>gle phase also<br />
Model No. MT-Z11<br />
FOUR POST LIST SUITABLE FOR WHEEL ALIGNMENT WITH BUILT IN WHEELS FREE LIFT<br />
1. Capacity : 3500 Kg<br />
2. Motor Capacity : 2.6 KW<br />
Model No. MT-Z12<br />
GAS ANALYSER (BLACK BOX VERSION)<br />
Model No. MT-Z13<br />
SMOKEMETER<br />
1. Peak and Average Smoke density measurements<br />
2. Measures <strong>in</strong> KM-1,HSU,FSN and mg/m³<br />
3. Free or Steady state operation use<br />
4. Rapid Warmup time and self zero<strong>in</strong>g facility<br />
5. Integral DOT Matrix pr<strong>in</strong>ter as standard supply<br />
6. Optional Trolley<br />
1. Measures CO,HC,CO2,O2<br />
2. Eng<strong>in</strong>e RPM for Sealed eng<strong>in</strong>es<br />
3. Oil Temperature measurement<br />
4. Air Fuel Ratio and Lambda Measurements<br />
5. Option to add Nox measurement facility<br />
6. OMIL Class1 category<br />
7. RS 232 Port<br />
PAGE<br />
56
Change language