Hardinge Custom Workholding Solutions
Hardinge Custom Workholding Solutions
Hardinge Custom Workholding Solutions
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Write in the type of Collet or Special:<br />
(5C, 16C, 1-1/4” Acme, etc.)<br />
Find the illustration containing the feature you require in one of the boxes<br />
shown over the next two pages. Check mark the box and record the dimensions<br />
on the corresponding lines below:<br />
1 Order Hole Size: ______________<br />
2 Order Hole, 2nd: ______________<br />
3 Number of Slots: _____________<br />
4 Radius: ___________________<br />
5 Bearing Length: ______________<br />
6 Bearing Length Front:___________<br />
7 Back Drill Dia.: ______________<br />
8 Relief Dia.: _________________<br />
9 Relief Length: _______________<br />
10 Depth of Step, 1st: ____________<br />
11 Depth of Step, 2nd.: ___________<br />
12 Auxiliary Hole Size: ____________<br />
13 Length of Extension: ___________<br />
14 Dia. at Face: ________________<br />
15 Degrees Taper/Chamfer: __________<br />
Send drawingS, Sample partS and all formS to:<br />
<strong>Hardinge</strong> Collet Sales Dept.<br />
One <strong>Hardinge</strong> Drive<br />
Elmira, New York 14902-1507<br />
Return Material Authorization<br />
(RMA#) required for <strong>Hardinge</strong><br />
to receive your Sample Part<br />
16 Front Dimension of Taper: ________<br />
17 Rear Dimension of Taper: ________<br />
18 Taper-Industrial Std: ____________<br />
19 Off Center Distance: ____________<br />
20 Order Hole - Width: ___________<br />
21 Order Hole - Length: ___________<br />
22 Thread Length: _______________<br />
23 Threads Per Inch: _____________<br />
24 Right/Left Hand Thrd.: __________<br />
25 Class Thread (1), (2), (3): ________<br />
26 Chamfer Depth: ______________<br />
27 Inscribed Circle: ______________<br />
28 Circumscribed Circle: ___________<br />
29 Clearance Bore: ______________<br />
30 Actuator Stroke: ______________<br />
Phone: 800-843-8801<br />
Canada: 800-468-5946<br />
Other countries: 607-378-4022<br />
Fax: 607-734-3886<br />
International Fax: 607-734-1701<br />
Email: info@hardingetooling.com<br />
Hexagon<br />
Eccentric to Corner<br />
Rectangular<br />
Eccentric - Short Side<br />
Round<br />
Eccentric<br />
Hexagon<br />
Eccentric to Flats<br />
Rectangular<br />
Eccentric - Long Side<br />
Triangular<br />
*One 6" length of stock required when ordering 1 to 3 collets;<br />
two 6" lengths for 4 to 7 collets; three 6" lengths for 8 to 11<br />
collets; four 6" lengths for 12 to 15 collets ordered.<br />
Square<br />
Eccentric to Flats<br />
Octagon<br />
Eccentric to Flat<br />
Special Extruded Shape<br />
Square<br />
Eccentric to Corner<br />
Octagon<br />
Eccentric to Corner<br />
Drawing & Sample Stock Required*<br />
• An extrusion drawing must indicate the<br />
centerline of the shape in relationship to<br />
the centerline of the collet.<br />
• Sample stock required.* If not available,<br />
manufacturing authorization is required<br />
prior to entry of order. If approved,<br />
item(s) will be manufactured with<br />
customer assuming full responsibility.<br />
• The confirming order.<br />
H A R D I N G E C U S T O M Q U O T E R E Q U E S T – 2 O F 4<br />
—this_page_may_be_duplicated—
Change language