- Page 1 and 2: CalComp Software Reference Manual
- Page 3 and 4: Copyright © 1976 by California Com
- Page 5: PREFACE This manual is intended to
- Page 11 and 12: Figure 1-1 1-2 2-1 2-2 2-3 2-4 2-5
- Page 14 and 15: Manual 1052 1056 1058 1061 1062 106
- Page 16 and 17: GENERAL SECTION 1 INTRODUCTION TO C
- Page 18 and 19: OFFLINE SYSTEM USER'S PROGRAM CALCO
- Page 20 and 21: Offline Systems CalComp drivers wit
- Page 23 and 24: Basic Software Basic software is a
- Page 26 and 27: TABLES Plotter/Driver Hardware SECT
- Page 28 and 29: Accuracy and Repeatability How accu
- Page 30 and 31: Accessories Drum plotter accessorie
- Page 32 and 33: 936 PLOTTER 33.0-inch (83.8 cm) dru
- Page 34 and 35: Figure 2-2. CalComp Flatbed Plotter
- Page 36: Flatbed Accessories (cont) • Tang
- Page 40 and 41: 1670 Options (cont) DRIVERS 105mm M
- Page 43 and 44: 905 CONTROLLER Integral Magnetic Ta
- Page 45 and 46: Digitizer Operation The 942 output
- Page 47: 1. 2130 SYSTEM, 16MM ONLINE TO IBM
- Page 53 and 54: SAMPLE PROGRAM (cont) 30 CALL PLOT
- Page 55 and 56: HCBS Subroutines (cont) rectly or i
- Page 58 and 59: Standard Calling Sequences (cont) X
- Page 61 and 62: CAL EDIT Basic Software (cont) Thes
- Page 66: o o o o m o o OJ o o o N to o o W·
- Page 74 and 75: Program Number 1 (cont) AGE=O. ° I
- Page 76: o CD o (D o r- o ill o (Y) o (\J o
- Page 80 and 81: Program Number 2 (cont) CALL SYMBOL
- Page 82: MODEL 942 DIGITIZER The CalComp Mod
- Page 92: Scaling for Multiple Curves (cont)
- Page 97 and 98: Using the WHERE Entry A typical use
- Page 99:
GENERAL SECTION 4 OPERATING CONSIDE
- Page 103 and 104:
PLANNING YOUR GRAPH (cont) A. The i
- Page 106 and 107:
ILLUSTRATIONS TABLES SECTION 5 (con
- Page 108 and 109:
905 Tape Format The CalComp Model 9
- Page 110 and 111:
905 Tape Format (cont) Legitimate s
- Page 112:
900 Tape Format (cont) following th
- Page 115 and 116:
Table 5-1. 900 Format Control Codes
- Page 118 and 119:
900 Tape Format (cant) 1670 CHARACT
- Page 120 and 121:
900 Tape Format (cont) SYMBOL MODE
- Page 124 and 125:
900 ONLINE FORMATS (cont) • A log
- Page 126 and 127:
Word Types (cont) D E, F G controls
- Page 128 and 129:
Word Types (cont) T u, V x, y The u
- Page 131 and 132:
Delta Commands (cont) Where: R DIR
- Page 133:
Table 5-5. 960 Characters Character
- Page 139:
The above conditions have no effect
- Page 143 and 144:
A CALL PLOT (XPAGE, YPAGE, IPEN)) ,
- Page 145 and 146:
-X,+Y +y +X, +Y -x +x -X,-y -Y +X,-
- Page 149:
8-Vector Algorithm (cont) Consequen
- Page 153 and 154:
Velocity Calculations (cont) In ord
- Page 156 and 157:
NEWPEN Subroutine (cont) EXAMPLE: T
- Page 158:
SYMBOL Design Symbols generated by
- Page 161:
SYMBOL Selection Tables (cont) If t
- Page 166 and 167:
CALL LINE (XARRAY, YARRAY, NPTS, IN
- Page 168 and 169:
70-75 RESET MINIMUM AND DELTA VALUE
- Page 171 and 172:
Flow of GCS (cont) The control sect
- Page 173 and 174:
READ Module The READ module contain
- Page 175 and 176:
YAY XAX Figure 5-11. SYMBOL Grid 5.
- Page 177 and 178:
GENERAL SECTION 6 FUNCTIONAL SOFTWA
- Page 179:
Standard Host COlnputer Subroutines
- Page 182 and 183:
Host Computer Symbol Sets CalComp o
- Page 186 and 187:
Host Computer Digitizer Support Sof
- Page 191 and 192:
Graphic Controller Microfiche Manag
- Page 193 and 194:
Graphic Controller Forms Overlay So
- Page 195 and 196:
GENERAL SECTION 7 APPLICATIONS SOFT
- Page 197:
phased (logical relationship) place
- Page 200 and 201:
TITLE: MANUAL: FROM NAME: POSITION: