- Page 1 and 2: CalComp Software Reference Manual
- Page 3 and 4: Copyright © 1976 by California Com
- Page 5: PREFACE This manual is intended to
- Page 11 and 12: Figure 1-1 1-2 2-1 2-2 2-3 2-4 2-5
- Page 14 and 15: Manual 1052 1056 1058 1061 1062 106
- Page 16 and 17: GENERAL SECTION 1 INTRODUCTION TO C
- Page 18 and 19: OFFLINE SYSTEM USER'S PROGRAM CALCO
- Page 20 and 21: Offline Systems CalComp drivers wit
- Page 23 and 24: Basic Software Basic software is a
- Page 26 and 27: TABLES Plotter/Driver Hardware SECT
- Page 28 and 29: Accuracy and Repeatability How accu
- Page 30 and 31: Accessories Drum plotter accessorie
- Page 32 and 33: 936 PLOTTER 33.0-inch (83.8 cm) dru
- Page 34 and 35: Figure 2-2. CalComp Flatbed Plotter
- Page 36: Flatbed Accessories (cont) • Tang
- Page 40 and 41: 1670 Options (cont) DRIVERS 105mm M
- Page 43 and 44: 905 CONTROLLER Integral Magnetic Ta
- Page 45: Digitizer Operation The 942 output
- Page 50: GENERAL SECTION 3 BASIC SOFTWARE Ca
- Page 54 and 55: SAMPLE PROGRAM (cont) 110 CALL PLOT
- Page 56: HeBS Subroutines (cont) Other chara
- Page 59: Standard Calling Sequences (cont) F
- Page 62: Electronic Basic Software (cont)
- Page 68: Program Number 1 (cont) CALL NUMBER
- Page 75 and 76: Program Number 2 CALL PLOTS (0,0,6)
- Page 78: Program Number 2 (cont) Plot the ax
- Page 81 and 82: Program Number 2 (cont) CALL SYHBOL
- Page 84: 942 Operating Procedure The origin
- Page 96 and 97:
Drawing Nonstandard AXIS Constructi
- Page 98 and 99:
OPERATING CONSIDERATIONS SECTION 4
- Page 101:
CONTROLLER INITIALIZATION Initializ
- Page 104:
PLANNING YOUR GRAPH (cont) F. After
- Page 107 and 108:
GENERAL SECTION 5 BASIC SOFTW ARE D
- Page 109 and 110:
905 Tape Format (cont) The format o
- Page 111 and 112:
900 Tape Format The 900 Tape Format
- Page 114 and 115:
Control Characters (Hex) 00 01 02 0
- Page 116:
900 Tape Format (cont) NO-OP SEARCH
- Page 119 and 120:
Table 5-2. Delta Values Which May B
- Page 121:
900 Tape Format (cont) Only those c
- Page 125 and 126:
Table 5-4. CAL EDIT System Paramete
- Page 127 and 128:
Word Types (cont) I, J M N P, Q, R,
- Page 129:
RS-232/936 SERIAL FORMAT The CalCom
- Page 132 and 133:
, Delta Commands ( con t) If the in
- Page 138 and 139:
DATA (BINARY) (OCTAL) FUNCTION 0000
- Page 142 and 143:
General Flow of PLOT Subroutine (co
- Page 144 and 145:
Special En tries Several of the Bas
- Page 146:
8-Vector Algorithm (con t) Therefor
- Page 151:
SET LOOP COUNTER = OX SET ACCUM = O
- Page 154:
Output Processing (cont) tape syste
- Page 157 and 158:
A. B. E. F. G. H. SET CONSTANTS DEP
- Page 160 and 161:
SYMBOL Selection Tables Every stand
- Page 165 and 166:
CALL AXIS (XPAGE, YPAGE, IBCD, NCHA
- Page 167 and 168:
CALL NUMBER (XPAGE, YPAGE, HEIGHT,
- Page 169:
AXIS, LINE, NUMBER, and SCALE Subro
- Page 172 and 173:
Table 5-7. 925 Controller Memory La
- Page 174 and 175:
SYMBOL Module The SYMBOL module con
- Page 176 and 177:
FUNCTIONAL SOFTWARE GENERAL Host Co
- Page 178 and 179:
Standard Host Computer Subroutines
- Page 181 and 182:
Standard Host Computer Subroutines
- Page 183:
Host Computer Symbol Sets (cont) Th
- Page 187:
Host Computer Polygon Painting Soft
- Page 192 and 193:
Graphic Controller Sizing Software
- Page 194 and 195:
APPLICATIONS SOFTWARE GENERAL SECTI
- Page 196 and 197:
grid mesh point values, and input k
- Page 199 and 200:
a smooth surface from a set of irre
- Page 201:
10Q5C 1.5K 876 PRINTED IN U.S.A. Ca