SMART Board User's Guide - Psychology

More documents

Recommendations

Info

Win or If you’re unsure of the correct COM port, click the Detect SMART Hardware button under Automatic to initiate hardware detection. Your COM ports will be searched for the presence of an attached interactive whiteboard until the correct COM port is located. The Ready Light on the Pen Tray will change from red to green, indicating the interactive whiteboard is now touch sensitive. Open the SMART Board tools to use any Pen Tray stylus to write over projected applications. Windows USB Adapter Cable Setup 1 Connect the short DB9 end of the optional USB adapter cable to the 9-pin serial port underneath the SMART Board (see the figure at the top of page iv). NOTE: To order a SMART USB adapter cable (part # USB-FRU), call your dealer. 2 Connect the USB connector at the other end of this cable to the USB port on your computer. 3 If you already have the appropriate USB driver installed on your system, the Ready Light on the Pen Tray will turn red and you can proceed to install SMART Board software (step 4 on the next page). If you don’t have the appropriate driver installed, a Found New Hardware wizard will appear to assist you in locating the driver for the newly connected USB Human Interface Device (the interactive whiteboard). • Direct the Windows operating system to search for an appropriate driver by clicking the Next button. • Click Next again to direct the Windows operating system to search the driver database on your hard drive for the appropriate driver. NOTE: If the Windows operating system fails to find the correct driver, insert the Windows 98/2000/ME/XP CD in your CD-ROM to install a USB HID (Human Interface Device) driver. USB HID drivers are typically not included in a default installation. HID is a subclass of USB devices. These drivers are needed for the interactive whiteboard to work using a USB cable. • Click the Finish button after the driver search or driver installation is complete. vi Preface USB Port
The Ready Light on the SMART Pen Tray will turn red. This indicates that the Pen Tray is receiving power from the USB port. Ready Light Insert the SMART Board software CD into your CD-ROM and follow the on-screen instructions to install SMART Board software. Immediately following the SMART Board software installation, you’ll notice the Ready Light on the Pen Tray turns from red to green. This indicates that the SMART Board interactive whiteboard is now fully touch sensitive. 4 If the SMART Board tools do not automatically open, select Start > Programs > SMART Board Software > SMART Board Tools. The SMART Board icon will appear in the system tray. You can now pick up a stylus from the Pen Tray and write over any projected application. 6 While not strictly necessary, we recommend that you press the SMART Board icon and select Orient to perform a brief orientation procedure to more accurately map the location of each interactive whiteboard contact (see page 9 for more information). Macintosh Computer USB Adapter Cable Setup 1 Connect the DB9 end of the optional USB adapter cable to the 9-pin serial port underneath the interactive whiteboard (see the figure at the top of page iv). 2 Connect the USB connector at the other end of this cable to the USB port on your computer (see the figure on previous page). The Ready Light on your Pen Tray will turn red, indicating that the interactive whiteboard is receiving power from the USB port. 3 Insert the SMART Board software CD into your computer’s CD-ROM drive. The CD will automatically launch the installation program. Follow the on-screen instructions. When installation is complete, the SMART Board icon will appear in the menu bar and the Ready Light on the Pen Tray will turn from red to green. 4 Press on the SMART Board icon and select Orient to perform a brief orientation procedure to more accurately track your touch on the interactive whiteboard (see page 9 for more information). Mac Preface vii
Page 1 and 2: User’s Guide ® ® for Microsoft
Page 3 and 4: Important Information Please read t
Page 5 and 6: Getting Started Getting your SMART
Page 7: 5 Turn on your computer. The Ready
Page 11 and 12: 3 With your Macintosh computer turn
Page 13 and 14: About This Guide As you read throug
Page 15 and 16: Contents Important Information ....
Page 17 and 18: Touch Shortcuts for PowerPoint Soft
Page 19 and 20: SMART Board Software SMART Board So
Page 21 and 22: Before a meeting or presentation, y
Page 23 and 24: SMART Board Control Panel The SMART
Page 25 and 26: Using Microsoft Word and Excel on a
Page 27 and 28: Using an Interactive Whiteboard wit
Page 29 and 30: Adjusting the Projected Image You m
Page 31 and 32: If Your Laptop’s Serial Port is U
Page 33 and 34: The Display Controller Wizard will
Page 35 and 36: Writing, Capturing and Erasing You
Page 37 and 38: To change the stylus settings: To c
Page 39 and 40: Two Buttons to Note: The Restore/Cl
Page 41 and 42: Saving Pen Tray and Floating Tools
Page 43 and 44: If you’d prefer to remove all ann
Page 45 and 46: Press here for Smooth Ink 4 Press O
Page 47 and 48: Using the SMART Keyboard to Type Te
Page 49 and 50: 5 Press the Commit button to transf
Page 51 and 52: To convert handwriting to all upper
Page 53 and 54: Using SMART Recorder If you’re a
Page 55 and 56: 3 To change sound and video quality
Page 57 and 58: 8 When the progress bar reaches 100
Page 59 and 60:
Using SMART Video Player SMART Vide
Page 61 and 62:
Using the Output from Video Hardwar
Page 63 and 64:
NOTE: If you create a large number
Page 65 and 66:
Writing with the Pen Tool To write
Page 67 and 68:
Assigning or Changing Text Attribut
Page 69 and 70:
A selection rectangle will emerge f
Page 71 and 72:
Rearranging Stacked Objects When yo
Page 73 and 74:
3 Tap once inside that circle to er
Page 75 and 76:
To create a new Notebook file: 1 Se
Page 77 and 78:
2 Select Save As Template File from
Page 79 and 80:
The Print dialog box appears. 2 Acc
Page 81 and 82:
The Templates dialog box will open,
Page 83 and 84:
NOTE: If the Floating Tools are act
Page 85 and 86:
Importing Scanned Pictures If you h
Page 87 and 88:
To capture a selected area or the e
Page 89 and 90:
Sorting Information in Notebook Sof
Page 91 and 92:
Unlike the Page Sorter, you can’t
Page 93 and 94:
To activate the Full Screen view on
Page 95 and 96:
Working with Board-Aware Third-Part
Page 97 and 98:
• If the Floating Tools are open,
Page 99 and 100:
4 Scroll to the application and dou
Page 101 and 102:
• To use a floating mouse, touch
Page 103 and 104:
Customer Support SMART’s Technica
Page 105 and 106:
The SMART Board driver is now ready
Page 107 and 108:
Tool Button Resulting Interactive W
Page 109 and 110:
Or, perhaps you’re presenting com
Page 111 and 112:
Downloading the Microsoft Web Publi
Page 113 and 114:
Reducing Screen Resolution and Disp
Page 115:
Suite 600, 1177 - 11th Avenue SW, C
show all

SMART Board User's Guide - Psychology

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?