STAR*NET V6 - Circe

More documents

Recommendations

Info

Appendix D Error and Warning Messages Could Not Compute Approximate Coordinates for Following Stations: Could Not Compute Approximate Elevations for Following Stations: Coordinates (or elevations in 3D adjustments) could not be automatically computed for the stations listed. There may not be enough observational data to create them. For certain types of data configurations, you may have to enter approximate coordinates for some or all stations in the network. For example, a trilateration network needs fixed or approximate coordinates for all stations. This error can also be caused by naming inconsistencies in the data. For example, if you name a point as “JOHN” in one observation line, and “John” in another, this will cause problems. Data Type Code Not Recognized A data line begins with a data type code not recognized by the program. 2D/3D/3R Dimension Changed During Current Traverse Mapmode Changed During Current Traverse You cannot turn the inline “.MAPMODE” on or off within a traverse. The mode may be changed before the “TB” line or after the “TE” line. Duplicate Names in AT, FROM, or TO Stations All names in AT-FROM-TO or FROM-TO station strings must be different. Excess or Unrecognizable Input Data A line of data contains more items than it should have for the specified data type, or a data item was encountered that <strong>STAR*NET</strong> did not know how to interpret. For example, on a 2D Measure “M” line, the program expects two observations plus either, two standard error values, or none. But in this case if only one such item was found, this error message would occur because the data item is unrecognizable. This error will often occur if you forget to properly set whether a job is a 2D or 3D job in the Adjustment Options, and you end up entering data of another dimention type the program cannot understand. Fatal Floating Point Error While Processing Station A math error, usually caused by a divide by zero, was encountered during processing. Although <strong>STAR*NET</strong> tries to trap all such errors, sometimes the problem occurs. Check your data for any unusual situations to see if you can determine the problem. If you cannot, contact technical support at Starplus Software for assistance. Inline Option Code Not Recognized Inline Option Code Not Unique An inline option code is either not one recognized by the program, or is abbreviated using too few letters such that it is not unique. 196
Appendix D Error and Warning Messages Fewer Than 2 Directions in Current Direction Set A direction set must contain two or more direction observations. Geometric Weakness at Station xxx Singularities Found During Solution During the processing of the adjustment, the equations happened to be formed in such a way that the solution could not continue. Sometimes this is caused by the observation data. It could be due to extremely weak intersection angles or very large standard error values on certain data lines, causing a geometric weakness and an inability to create a proper solution. Sometimes, controlling coordinates are entered with one or more north, east or elevations components having very minimal or no fixity can cause the problem. Check your data for any unusual situations to see if you can determine the reason. If you cannot, contact technical support at Starplus Software for assistance. We may request a copy of your project be sent to us via email. Instrument Block Name Not Found A block named using the “.INSTRUMENT” inline code is not defined in the instrument library. It has been either misspelled, or has not been previously defined in the library. Invalid Level Weight Invalid Level Data Bad information on an “LW” data line which defines the weighting value to use for differential level data, or on an “L” line defining the leveling observation. Measured/Grid Mode Changed During Current Traverse You cannot change the data dimension using “.2D, .3D or .3R” inlines within a traverse. Likewise you cannot change “mapmode” or whether observations are “measured: or “grid” values during a traverse. Missing or Invalid Coordinate Value Missing or Invalid Direction Missing or Invalid Distance Missing or Invalid Elevation Difference Missing or Invalid GPS Vector Missing or Invalid Horizontal Angle Missing or Invalid Position Value Missing or Invalid Station List Missing or Invalid Zenith Angle These errors and other “Missing or Invalid” messages not shown indicate an error has been found while trying to read one of the types of data described in the error message. The actual data line is printed below the error message and an attempt is made to show you exactly where the problem was encountered. 197
Page 1 and 2:
STAR*NET V6 Least Squares Survey Ad
Page 3 and 4:
TABLE OF CONTENTS Chapter 1 OVERVIE
Page 5:
10.9 Entering a Geoid Height and Ve
Page 8 and 9:
Chapter 1 Overview 4. Survey planni
Page 10 and 11:
Chapter 2 Installation 2.3 Starting
Page 12 and 13:
2.7 The Registry Chapter 2 Installa
Page 14 and 15:
3.3 The Menu System Chapter 3 Using
Page 16 and 17:
3.8 Checking the Error File Chapter
Page 18 and 19:
Chapter 3 Using STAR*NET 3.12 Displ
Page 20 and 21:
Chapter 4 Options 4.2 Changing Proj
Page 22 and 23:
Option Group: Units Chapter 4 Optio
Page 24 and 25:
General Options Chapter 4 Options T
Page 26 and 27:
Chapter 4 Options Option Group: Dis
Page 28 and 29:
Chapter 4 Options What standard err
Page 30 and 31:
Chapter 4 Options The default metho
Page 32 and 33:
Option Group: Adjusted Contents Cha
Page 34 and 35:
Other Files Options Chapter 4 Optio
Page 36 and 37:
Chapter 4 Options Creating a Ground
Page 38 and 39:
Special Options Chapter 4 Options T
Page 40 and 41:
4.5 Company Options Chapter 4 Optio
Page 42 and 43:
Chapter 4 Options Note that any dat
Page 44 and 45:
Chapter 4 Options When the Instrume
Page 46 and 47:
Using the Input Data Files Dialog C
Page 48 and 49:
Chapter 5 Preparing Input Data 5.5
Page 50 and 51:
Station Names Chapter 5 Preparing I
Page 52 and 53:
Chapter 5 Preparing Input Data Zeni
Page 54 and 55:
Point Descriptors Chapter 5 Prepari
Page 56 and 57:
Example 1: (2D Data) Chapter 5 Prep
Page 58 and 59:
Chapter 5 Preparing Input Data The
Page 60 and 61:
Chapter 5 Preparing Input Data SING
Page 62 and 63:
The “V” Code: Vertical Observat
Page 64 and 65:
Chapter 5 Preparing Input Data Samp
Page 66 and 67:
Example 2: (2D Data) Chapter 5 Prep
Page 68 and 69:
Page 70 and 71:
Chapter 5 Preparing Input Data TRAV
Page 72 and 73:
Chapter 5 Preparing Input Data Exam
Page 74 and 75:
The “TE” Code: Ending a Travers
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Chapter 5 Preparing Input Data LEVE
Page 82 and 83:
Chapter 5 Preparing Input Data SIDE
Page 84 and 85:
Chapter 5 Preparing Input Data Usin
Page 86 and 87:
INLINE OPTION: .DELTA ON/OFF Chapte
Page 88 and 89:
INLINE OPTION: .SCALE Value Chapter
Page 90 and 91:
Chapter 5 Preparing Input Data INLI
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Chapter 5 Preparing Input Data Lega
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
How do I weight observations? Chapt
Page 108 and 109:
Chapter 5 Preparing Input Data 102
Page 110 and 111:
Chapter 6 Running Adjustments The S
Page 112 and 113:
6.5 Preanalysis Chapter 6 Running A
Page 114 and 115:
Chapter 6 Running Adjustments 108
Page 116 and 117:
Chapter 7 Viewing and Printing Outp
Page 118 and 119:
7.4 Viewing the Error File Chapter
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Chapter 8 Analysis of Adjustment Ou
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
To run the utility, follow these st
Page 146 and 147:
Chapter 9 Tools As discussed above,
Page 148 and 149:
Chapter 9 Tools A few words should
Page 150 and 151:
Chapter 9 Tools The settings select
Page 152 and 153: Chapter 10 Adjustments in Grid Coor
Page 168 and 169: APPENDIX A - TOUR OF THE STAR*NET P
Page 170 and 171: Appendix A STAR*NET Tutorial Exampl
Page 172 and 173: Appendix A STAR*NET Tutorial 4. Rev
Page 174 and 175: Appendix A STAR*NET Tutorial 7. Fin
Page 176 and 177: Appendix A STAR*NET Tutorial 12. To
Page 178 and 179: Appendix A STAR*NET Tutorial Take a
Page 186 and 187: Appendix A STAR*NET Tutorial Before
Page 188 and 189: Example 5: Resection Appendix A STA
Page 192 and 193: Example 7: Preanalysis Appendix A S
Page 194 and 195: 188
Page 196 and 197: Appendix B References 6. Mikhail, E
Page 198 and 199: Appendix C Additional Technical Inf
Page 200 and 201: Appendix C Additional Technical Inf
Page 204 and 205: Appendix D Error and Warning Messag
Page 206 and 207: Appendix D Error and Warning Messag
Page 208 and 209: Data Lines, General Content Data Ty
Page 210 and 211: Index Installation Installing, 3 Se
Page 212: STARPLUS SOFTWARE, INC.
show all

STAR*NET V6 - Circe

Create successful ePaper yourself

Delete template?

Save as template?