Download the above ground pool manual - Club Piscine
Download the above ground pool manual - Club Piscine
Download the above ground pool manual - Club Piscine
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
6. Maintenance<br />
Proper maintenance is <strong>the</strong> key to keeping your <strong>pool</strong> in good condition and filled with clear, clean water.<br />
Please read <strong>the</strong>se instructions thoroughly, and follow <strong>the</strong>m carefully. Only a few minutes a day will keep<br />
your <strong>pool</strong> in perfect condition.<br />
1) BACKWASHInG<br />
We recommend you backwash once a week. This must also be done when <strong>the</strong> pressure gauge measures<br />
higher than normal (over 10 pounds) and each time you vacuum. This operation consists of reversing <strong>the</strong><br />
water flow through <strong>the</strong> filter pipes and sand. Here are <strong>the</strong> steps to follow:<br />
Caution ! Each time you change <strong>the</strong> position of <strong>the</strong> filter handle, shut off <strong>the</strong> motor and re-start it<br />
once <strong>the</strong> change has been made.<br />
• Unroll <strong>the</strong> backwash hose to its full length and turn off <strong>the</strong> pump.<br />
• Move <strong>the</strong> filter handle to “BACKWASH.”<br />
• Run <strong>the</strong> pump for two or three seconds <strong>the</strong>n turn it off. This will open up <strong>the</strong> tube so that it will not burst<br />
or split from <strong>the</strong> pressure.<br />
• Run <strong>the</strong> pump for two to three minutes during <strong>the</strong> weekly cleaning, or four to five minutes when opening,<br />
or closing your <strong>pool</strong>, or until <strong>the</strong> water in <strong>the</strong> glass bottle is clear.<br />
• Turn off <strong>the</strong> pump.<br />
• Move <strong>the</strong> filter handle to “RECIRCULATE” or “WHIRLPOOL.”<br />
• Run <strong>the</strong> pump for one minute. This will enable <strong>the</strong> sand to settle at <strong>the</strong> bottom of <strong>the</strong> filter.<br />
Turn off <strong>the</strong> pump.<br />
• Move <strong>the</strong> filter control handle to “RINSE.” Run <strong>the</strong> pump for 30 seconds. This will get rid of any debris<br />
redeposited on <strong>the</strong> surface of <strong>the</strong> sand. If you do not have this setting, some debris may return to <strong>the</strong> <strong>pool</strong><br />
after backwashing. Turn off <strong>the</strong> pump.<br />
• Return <strong>the</strong> control handle to “FILTER” and turn on <strong>the</strong> pump.<br />
2) VACUUM<br />
• If your <strong>pool</strong> had a bottom drain, put <strong>the</strong> three-way valve control handle at “SKIMMER”<br />
(pointing downwards) so that <strong>the</strong> skimmer does not run.<br />
• Make sure <strong>the</strong> water is at <strong>the</strong> ideal level, ¾ of <strong>the</strong> way up <strong>the</strong> skimmer.<br />
• Connect <strong>the</strong> vacuum hose to <strong>the</strong> vacuum head.<br />
note : If your vacuum hose has one end that swivels, connect this end to <strong>the</strong> vacuum head,<br />
not <strong>the</strong> skimmer. The swivel head will prevent <strong>the</strong> hose from becoming tangled<br />
when <strong>the</strong> vacuum head turns in <strong>the</strong> water.<br />
• Connect <strong>the</strong> telescoping pole to <strong>the</strong> handle on <strong>the</strong> vacuum head.<br />
• Lower <strong>the</strong> vacuum head into <strong>the</strong> water.<br />
• Put <strong>the</strong> non-pivoting end of <strong>the</strong> hose into <strong>the</strong> water return while holding <strong>the</strong> pole tightly. The hose will fill<br />
with water, and <strong>the</strong> air will exit from underneath <strong>the</strong> head. When <strong>the</strong>re are no more air bubbles coming<br />
out, <strong>the</strong> hose is full of water and ready to connect to <strong>the</strong> skimmer. Turn off <strong>the</strong> pump.<br />
• Place <strong>the</strong> vacuum adapter on <strong>the</strong> skimmer basket and attach <strong>the</strong> non-pivoting end of <strong>the</strong> vacuum hose<br />
to <strong>the</strong> adapter. If <strong>the</strong> vacuum has an elbow, attach it to <strong>the</strong> adapter and connect <strong>the</strong> hose to <strong>the</strong> elbow.<br />
• Leave <strong>the</strong> filter handle at “FILTER” for regular maintenance.<br />
11 <strong>Club</strong> <strong>Piscine</strong> Super Fitness - Above Ground Swimming Pool - Owner’s Manual (03/2012)