T2 Humeral Nailing System Operative Technique - Stryker

More documents

Recommendations

Info

Ordering Information – Instruments 48 REF Description Optional Instruments 1806-0003 1806-0045 1806-0083 1806-0093 1806-0083S 1806-0093S 1806-0130 1806-0175 1806-3540S 1806-3550 1806-3550S 1806-4000S 1806-9013 1806-9972 1806-9982 X-Ray Template, Humerus Awl, Ø10mm Straight Guide Wire, Ball Tip, Ø2.5 × 800mm Guide Wire, Smooth Tip, Ø2.2 × 800mm Guide Wire, Ball Tip, Ø2.5 × 800mm, Sterile (U.S.) Guide Wire, Smooth Tip, Ø2.2 × 800mm, Sterile (U.S.) Wrench, 8mm/10mm Sliding Hammer Drill Ø3.5 × 230mm, AO, sterile (U.S.) Drill Ø3.5 × 130mm, AO, (outside of U. S.) Drill Ø3.5 × 130mm, AO, sterile (U.S.) Drill Ø 4 × 180mm, AO, Sterile (U.S.) Humerus Screw Tray <strong>T2</strong> PHN Drill Rack Silicon Mat * Instruments designated “Outside of the U.S.” may not be ordered for the U.S. market.
Ordering Information – Instruments Bixcut Typical Standard Reamer Ø14mm C le a r a nc e a re a : 32% of cross section Bixcut Reamer Ø14mm Clearance area : 59% of cross section Bixcut 49 Complete range of modular and fixed-head reamers to match surgeon preference and optimize O. R. efficiency, presented in fully sterilizable cases. Large clearance rate resulting from reduced number of reamer blades coupled with reduced length of reamer head to allow for effective relief of pressure and efficient removal of material 3 . Cutting flute geometry optimized to lower pressure generation 3 . Forward- and side-cutting face combination produces efficient material removal and rapid clearance 3 . Double-wound shaft transmits torque effectively and with high reliability. Low-friction surface finish aids rapid debris clearance 3 . Smaller, 6 and 8mm shaft diameters are designed to reduce IM pressure. Studies 1 have demonstrated that the pressures developed within the medullary cavity through the introduction of unreamed IMnails can be far greater than those devel oped during reaming − but this depends very much upon the design of the reamer. After a three year development study 2 involving several universities, the factors that determine the pressures and temperatures developed during reaming were clearly established. These factors were applied to the de - velopment of advanced reamers that demonstrate significantly better per - form ance than the best of previous designs 3. 1 Jan Paul M. Frolke, et al. ; Intramedullary Pressure in Reamed Femoral <strong>Nailing</strong> with Two Different Reamer Designs., Eur. J. of Trauma, 2001 #5 2 Medhi Moussavi, et al.; Pressure Changes During Reaming with Different Parameters and Reamer Designs, Clinical Orthopaedics and Related Research Number 373, pp. 295-303, 2000 3 Andreas Speitling; Intramedullary Reamers, commented slides of internal test report, Sep 1999
Page 1 and 2: T2 Humeral Nailing System Operative
Page 3 and 4: Contents Page 1. Introduction 4 Imp
Page 5 and 6: Introduction Technical Details Nail
Page 7 and 8: References 1. J. Blum et al., Unrea
Page 9 and 10: Pre-operative Planning An X-Ray Tem
Page 11 and 12: Locking Options Dynamic Mode Apposi
Page 13 and 14: Operative Technique - Antegrade Tec
Page 29 and 30: Operative Technique - Retrograde Te
Page 45 and 46: 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0
Page 47: Ordering Information - Instruments
Page 51 and 52: Notes 51

T2 Humeral Nailing System Operative Technique - Stryker

Create successful ePaper yourself

Delete template?

Save as template?