Consumeables Catalog - Lincoln Electric
Consumeables Catalog - Lincoln Electric Consumeables Catalog - Lincoln Electric
PIPELINER ® FLUX-CORED GAS-SHIELDED (FCAW-G) WIRE Pipeliner® 81M Low Alloy, All Position • AWS E81T1-GM Key Features Designed for optimal performance in automated pipe welding applications where a consistent arc length is critical. Flat bead shape, fast freezing slag provides consistent puddle support all the way around the pipe. Capable of producing weld deposits with impact toughness exceeding 27 J (20 ft•lbf) at -40°C (-40°F). Q2 Lot ® - Certificate showing actual deposit chemistry and mechanical properties per lot available online. ProTech ® foil bag packaging DIAMETERS / PACKAGING Diameter 10 lb (4.5 kg) Plastic Spool 25 lb (11.3 kg) Plastic Spool mm (in) (Vacuum Sealed Foil Bag) (Vacuum Sealed Foil Bag) 1.2 (0.047) ED033320 ED033321 TYPICAL OPERATING PROCEDURES Diameter, Polarity, Shielding Gas 1.2 mm (0.047 in), DC+, 75-85% Ar/ balance CO2 CTWD (5) mm (in) 19 (3/4) 306 ı THE LINCOLN ELECTRIC COMPANY Typical Applications Welding Positions All Hot, fill and cap pass welding on up to X70 grade pipe Fully automated pipe welding Meets requirements for NACE applications Conformances AWS A5.29/A5.29M: 2010 ASME SFA-5.29 ISO 17632: 2006 Shielding Gas 75 - 85% Argon / Balance CO2 Flow Rate: 40 - 50 CFH E81T1-GM E81T1-GM ISO 17632-B-T554T1-1MA-N1-UH5 MECHANICAL PROPERTIES (1) – As Required per AWS A5.29/A5.29M: 2010 Yield Strength (2) Charpy V-Notch Tensile Strength Elongation J (ft•lbf) MPa (ksi) MPa (ksi) % @-29°C (-20°F) @-40°C (-40°F) Requirements - AWS E81T1-GM Typical Results 470 (68) min. 550-690 (80-100) 19 min. Not Specified Not Specified (3) As-Welded with 75% Ar/25% CO2 510-560 (74-81) 580-620 (84-90) 25-29 83-149 (61-110) 66-131 (49-97) DEPOSIT COMPOSITION (1) – As Required per AWS A5.29/A5.29M: 2010 %C %Mn %Si %P Requirements - AWS E81T1-GM Not Specified 0.50 (4) 1.00 (4) Typical Results 0.030 max. (3) As-Welded with 75% Ar/25% CO2 0.06-0.07 1.54-1.68 0.34-0.37 0.010-0.015 %S %Ni Diffusible Hydrogen (mL/100g weld deposit) Requirements - AWS E81T1-GM 0.030 max. 0.50 (4) Typical Results Not Specified (3) As-Welded with 75% Ar/25% CO2 0.010-0.020 0.85 4-5 Wire Feed Speed Voltage Approx. Current Melt-Off Rate m/min (in/min) (volts) (amps) kg/hr (lb/hr) 4.4-10.2 (175 - 400) 23-30 130 - 275 1.8-4.1 (3.9-9.0) (1) Typical all weld metal. (2) Measured with 0.2% offset. (3) See test results disclaimer below. (4) In order to meet the requirements of the G group, the undiluted weld metal shall have not less than the minimum specified for one or more of the elements listed. (5) Strength and elongation properties were obtained from a 0.500 in. tensile specimen artificially aged at 104°C (220°F) for 48 hours as permitted by AWS A5.29:2005. NOTE: This product contains micro-alloying elements. Additional information available upon request.
Typical Applications Hot, fill and cap pass welding on up to X80 grade pipe Fully automated pipe welding Semi-automatic pipe welding Meets requirements for NACE applications Conformances AWS A5.29/A5.29M: 2010 ASME SFA-A5.29 ISO 18276: 2006 Shielding Gas 75-80% Argon / Balance CO2 Flow Rate: 40-60 CFH E101T1-GM E101T1-GM ISO 18276-B- T694T1-1MA-N2M2-UH5 PIPELINER ® FLUX-CORED GAS-SHIELDED (FCAW-G) WIRE Pipeliner ® Welding Positions All 101M AWS E101T1-GM • Low Alloy, All Position Key Features Designed for optimal performance in automated pipe welding applications where a consistent arc length is critical Fast freezing slag provides consistent puddle support all the way around the pipe Capable of producing weld deposits with impact toughness exceeding 27 J (20 ft•lbf) at -40°C (-40°F) Q2 Lot ® - Certificate showing actual deposit chemistry and mechanical properties per lot available online. ProTech ® foil bag packaging DIAMETERS / PACKAGING Diameter 10 lb (4.5 kg) Plastic Spool 25 lb (11.3 kg) Plastic Spool mm (in) (Vacuum Sealed Foil Bag) (Vacuum Sealed Foil Bag) 1.2 (0.047) ED033807 ED033808 MECHANICAL PROPERTIES (1) – As Required per AWS A5.29/A5.29M: 2010 Yield Strength (2) Tensile Strength Elongation Charpy V-Notch J (ft•lbf) MPa (ksi) MPa (ksi) % @-40°C (-40°F) Requirements - AWS E101T1-GM Typical Results 610 (88) min. 690-830 (100-120) 16 min. Not Specified (3) As-Welded with 75% Ar/Balance CO2 660-670 (95-97) 700-720 (101-104) 23-25 61-91 (45-68) DEPOSIT COMPOSITION (1) – As Required per AWS A5.29/A5.29M: 2010 %C %Mn %Si %P Requirements - AWS E101T1-GM Not Specified 0.50 (4) Typical Results 1.00 max. 0.030 max. (3) As-Welded with 75% Ar/25% CO2 0.06 1.48-1.61 0.29-0.31 0.008 Diffusible Hydrogen %S %Ni %Mo (mL/100g weld deposit) Requirements - AWS E101T1-GM 0.030 max. 0.50 (4) 0.20 (4) Typical Results Not Specified (3) As-Welded with 75% Ar/25% CO2 0.007 0.76-0.84 0.34-0.36 4-5 TYPICAL OPERATING PROCEDURES Diameter, Polarity, Shielding Gas 1.2 mm (0.045 in), DC+, 75-80% Ar/ balance CO2 CTWD (5) mm (in) 19 (3/4) Wire Feed Speed Voltage Approx. Current Melt-Off Rate m/min (in/min) (volts) (amps) kg/hr (lb/hr) 4.4-10.2 (175-400) 23-30 130-275 1.8-4.1 (3.9-9.0) (1) Typical all weld metal. (2) Measured with 0.2% offset. (3) See test results disclaimer below. (4) In order to meet the requirements of the G group, the undiluted weld metal shall have not less than the minimum specified for one or more of the elements listed. (5) Strength and elongation properties were obtained from a 0.500 in. tensile specimen artificially aged at 104°C (220°F) for 48 hours as permitted by AWS A5.29: 2010. NOTE: This product contains micro-alloying elements. Additional information available upon request. WELDING CONSUMABLES CATALOG ı 307
- Page 258 and 259: HARDFACING FLUX-CORED SELF-SHIELDED
- Page 260 and 261: HARDFACING FLUX-CORED SELF-SHIELDED
- Page 262 and 263: HARDFACING METAL-CORED SUBMERGED AR
- Page 264 and 265: HARDFACING METAL-CORED SUBMERGED AR
- Page 266 and 267: HARDFACING METAL-CORED SUBMERGED AR
- Page 268 and 269: HARDFACING METAL-CORED SUBMERGED AR
- Page 270 and 271: HARDFACING METAL-CORED SUBMERGED AR
- Page 272 and 273: HARDFACING METAL-CORED SUBMERGED AR
- Page 274 and 275: HARDFACING METAL-CORED SUBMERGED AR
- Page 276 and 277: HARDFACING METAL-CORED SUBMERGED AR
- Page 278 and 279: HARDFACING SUBMERGED ARC (SAW) FLUX
- Page 280 and 281: HARDFACING SUBMERGED ARC (SAW) FLUX
- Page 282 and 283: MIG (GMAW) WIRE SuperGlaze Aluminum
- Page 284 and 285: MIG (GMAW) WIRE SuperGlaze Aluminum
- Page 286 and 287: MIG (GMAW) WIRE SuperGlaze Aluminum
- Page 288 and 289: SuperGlaze ® MIG (GMAW) WIRE Alumi
- Page 290 and 291: TIG (GTAW) CUT LENGTHS SuperGlaze A
- Page 292 and 293: ALUMINUM & CAST IRON CONSUMABLES No
- Page 294 and 295: PIPELINER ® STICK (SMAW) ELECTRODE
- Page 296 and 297: PIPELINER ® STICK (SMAW) ELECTRODE
- Page 298 and 299: PIPELINER ® STICK (SMAW) ELECTRODE
- Page 300 and 301: PIPELINER ® STICK (SMAW) ELECTRODE
- Page 302 and 303: PIPELINER ® STICK (SMAW) ELECTRODE
- Page 304 and 305: Pipeliner® Welding Positions All P
- Page 306 and 307: PIPELINER ® FLUX-CORED SELF-SHIELD
- Page 310 and 311: PIPELINER ® FLUX-CORED GAS-SHIELDE
- Page 312 and 313: PIPELINER ® CONSUMABLES Electrode
- Page 314 and 315: PIPELINER ® CONSUMABLES Electrode
- Page 316 and 317: PIPELINER ® CONSUMABLES EN and ISO
- Page 318 and 319: Agency Approvals NOTE: Approvals ar
- Page 320 and 321: PIPELINER ® CONSUMABLES Notes 318
- Page 322 and 323: Power Generation & Nuclear Lincoln
- Page 324 and 325: BATCH | STICK (SMAW) ELECTRODE Exca
- Page 326 and 327: STICK (SMAW) ELECTRODE Excalibur®
- Page 328 and 329: STICK (SMAW) ELECTRODE Excalibur®
- Page 330 and 331: BATCH | MIG (GMAW) WIRE SuperArc®
- Page 332 and 333: BATCH | MIG (GMAW) WIRE SuperArc®
- Page 334 and 335: BATCH | MIG (GMAW) WIRE Blue Max®
- Page 336 and 337: BATCH | MIG (GMAW) WIRE Blue Max®
- Page 338 and 339: BATCH | MIG (GMAW) WIRE Blue Max®
- Page 340 and 341: BATCH | MIG (GMAW) WIRE Blue Max®
- Page 342 and 343: TIG (GTAW) CUT LENGTHS Lincoln® Lo
- Page 344 and 345: BATCH | TIG (GTAW) CUT LENGTHS Linc
- Page 346 and 347: BATCH | ORBITAL TIG (GTAW) WIRE Sup
- Page 348 and 349: BATCH | FLUX-CORED GAS-SHIELDED (FC
- Page 350 and 351: FLUX-CORED GAS-SHIELDED (FCAW-G) WI
- Page 352 and 353: SUBMERGED ARC (SAW) FLUX AND WIRE C
- Page 354 and 355: SUBMERGED ARC (SAW) WIRE AND FLUX L
- Page 356 and 357: SUBMERGED ARC (SAW) WIRE AND FLUX L
PIPELINER ® FLUX-CORED GAS-SHIELDED (FCAW-G) WIRE<br />
Pipeliner®<br />
81M<br />
Low Alloy, All Position • AWS E81T1-GM<br />
Key Features<br />
Designed for optimal performance in automated<br />
pipe welding applications where a consistent<br />
arc length is critical.<br />
Flat bead shape, fast freezing slag provides<br />
consistent puddle support all the way around<br />
the pipe.<br />
Capable of producing weld deposits with<br />
impact toughness exceeding 27 J (20 ft•lbf)<br />
at -40°C (-40°F).<br />
Q2 Lot ® - Certificate showing actual deposit<br />
chemistry and mechanical properties per lot<br />
available online.<br />
ProTech ® foil bag packaging<br />
DIAMETERS / PACKAGING<br />
Diameter 10 lb (4.5 kg) Plastic Spool<br />
25 lb (11.3 kg) Plastic Spool<br />
mm (in)<br />
(Vacuum Sealed Foil Bag)<br />
(Vacuum Sealed Foil Bag)<br />
1.2 (0.047) ED033320 ED033321<br />
TYPICAL OPERATING PROCEDURES<br />
Diameter, Polarity,<br />
Shielding Gas<br />
1.2 mm (0.047 in), DC+,<br />
75-85% Ar/ balance CO2 CTWD (5)<br />
mm (in)<br />
19 (3/4)<br />
306 ı THE LINCOLN ELECTRIC COMPANY<br />
Typical Applications<br />
Welding Positions<br />
All<br />
Hot, fill and cap pass welding on up to X70 grade pipe<br />
Fully automated pipe welding<br />
Meets requirements for NACE applications<br />
Conformances<br />
AWS A5.29/A5.29M: 2010<br />
ASME SFA-5.29<br />
ISO 17632: 2006<br />
Shielding Gas<br />
75 - 85% Argon / Balance CO2 Flow Rate: 40 - 50 CFH<br />
E81T1-GM<br />
E81T1-GM<br />
ISO 17632-B-T554T1-1MA-N1-UH5<br />
MECHANICAL PROPERTIES (1) – As Required per AWS A5.29/A5.29M: 2010<br />
Yield Strength (2) Charpy V-Notch<br />
Tensile Strength Elongation<br />
J (ft•lbf)<br />
MPa (ksi) MPa (ksi) % @-29°C (-20°F) @-40°C (-40°F)<br />
Requirements - AWS E81T1-GM<br />
Typical Results<br />
470 (68) min. 550-690 (80-100) 19 min. Not Specified Not Specified<br />
(3)<br />
As-Welded with 75% Ar/25% CO2 510-560 (74-81) 580-620 (84-90) 25-29 83-149 (61-110) 66-131 (49-97)<br />
DEPOSIT COMPOSITION (1) – As Required per AWS A5.29/A5.29M: 2010<br />
%C %Mn %Si %P<br />
Requirements - AWS E81T1-GM Not Specified 0.50 (4) 1.00 (4) Typical Results<br />
0.030 max.<br />
(3)<br />
As-Welded with 75% Ar/25% CO2 0.06-0.07 1.54-1.68 0.34-0.37 0.010-0.015<br />
%S %Ni<br />
Diffusible Hydrogen<br />
(mL/100g weld deposit)<br />
Requirements - AWS E81T1-GM 0.030 max. 0.50 (4) Typical Results<br />
Not Specified<br />
(3)<br />
As-Welded with 75% Ar/25% CO2 0.010-0.020 0.85 4-5<br />
Wire Feed Speed Voltage Approx. Current Melt-Off Rate<br />
m/min (in/min) (volts) (amps) kg/hr (lb/hr)<br />
4.4-10.2<br />
(175 - 400)<br />
23-30 130 - 275<br />
1.8-4.1<br />
(3.9-9.0)<br />
(1) Typical all weld metal. (2) Measured with 0.2% offset. (3) See test results disclaimer below. (4) In order to meet the requirements of the G group, the undiluted weld metal shall have not less than the minimum specified for one or more of the elements listed. (5) Strength<br />
and elongation properties were obtained from a 0.500 in. tensile specimen artificially aged at 104°C (220°F) for 48 hours as permitted by AWS A5.29:2005. NOTE: This product contains micro-alloying elements. Additional information available upon request.