Consumeables Catalog - Lincoln Electric
Consumeables Catalog - Lincoln Electric Consumeables Catalog - Lincoln Electric
HARDFACING METAL-CORED SUBMERGED ARC (SAW) ELECTRODE Lincore® 423L Roll Rebuilding - Metal-to-Metal Key Features Metal-cored wire, provides a softer “as-welded” deposit than Lincore ® 420 More resistance to softening during tempering above 482°C (900°F) 270 ı THE LINCOLN ELECTRIC COMPANY Typical Applications Caster rolls Recommended Flux Primary Flux (1) 802 DIAMETERS / PACKAGING Diameter 600 lb (272 kg) Speed-Feed ® in (mm) Drum 1/8 (3.2) ED018551 MECHANICAL PROPERTIES (1) DEPOSIT COMPOSITION (1) Rockwell Hardness (R C ) 41-47 With Recommended Neutral Flux %C %Mn %Si %Cr %Ni %Mo %V 0.15 1.20 0.40 11.50 2.00 1.00 0.15 TYPICAL OPERATING PROCEDURES Diameter, Polarity Wire Feed Speed Voltage Approx. Current Deposition Rate ESO - in (mm) m/min (in/min) (Volts) (Amps) kg/hr (lb/hr) 1/8 in (3.2 mm), DC+ 1-5/8 (40) 1.5 (60) 2.5 (100) 3.6 (140) 26 28 30 350 500 610 4.2 (9.3) 7.0 (15.5) 9.8 (21.7) IMPORTANT: SPECIAL VENTILATION AND/OR EXHAUST REQUIRED Fumes from the normal use of some welding products can contain significant quantities of components - such as chromium and manganese - which can lower the 5.0 mg/m3 maximum exposure guideline for general welding fume. BEFORE USE, READ AND UNDERSTAND THE MATERIAL SAFETY DATA SHEET (MSDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. (1) Composition and properties depend upon dilution. Single layer deposit properties depend upon base metal and/or build-up material. (1) 802 and 860 standard flux are not sized for semiautomatic applications; however, they can be ordered in special sizing by contacting your Lincoln Electric representative.
Typical Applications HARDFACING METAL-CORED SUBMERGED ARC (SAW) ELECTRODE Lincore® 423Cr Caster rolls Metal-cored wire with a higher chrome deposit than Lincore ® 423L for improved corrosion resistance Recommended Flux Primary Flux (1) 802 (1) 802 and 860 standard flux are not sized for semiautomatic applications; however, they can be ordered in special sizing by contacting your Lincoln Electric representative. Roll Rebuilding - Metal-to-Metal Key Features DIAMETERS / PACKAGING Diameter 50 lb (22.7 kg) 600 lb (272 kg) Coil Speed-Feed ® in (mm) Drum 3/32 (2.4) EDS18553 1/8 (3.2) EDS18554 ED018557 MECHANICAL PROPERTIES (1) Rockwell Hardness (R C ) DEPOSIT COMPOSITION (1) With Recommended Neutral Flux %C %Mn %Si %Cr %Ni %Mo %V 41-47 0.15 1.20 0.40 13.50 2.00 1.00 0.15 TYPICAL OPERATING PROCEDURES Diameter, Polarity Wire Feed Speed Voltage Approx. Current Deposition Rate ESO - in (mm) m/min (in/min) (Volts) (Amps) kg/hr (lb/hr) 3/32 in (2.4 mm), DC+ 1-1/2 (38) 1.7 (65) 3.0 (120) 4.4 (175) 24 28 31 250 350 450 2.7 (6.0) 5.0 (11.0) 7.3 (16.0) 1/8 in (3.2 mm), DC+ 1-5/8 (40) 1.5 (60) 2.5 (100) 3.6 (140) 26 28 30 375 540 640 4.5 (9.9) 7.5 (16.5) 10.5 (23.1) IMPORTANT: SPECIAL VENTILATION AND/OR EXHAUST REQUIRED Fumes from the normal use of some welding products can contain significant quantities of components - such as chromium and manganese - which can lower the 5.0 mg/m3 maximum exposure guideline for general welding fume. BEFORE USE, READ AND UNDERSTAND THE MATERIAL SAFETY DATA SHEET (MSDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. (1) Composition and properties depend upon dilution. Single layer deposit properties depend upon base metal and/or build-up material. WELDING CONSUMABLES CATALOG ı 271
- Page 222 and 223: FLUX-CORED GAS-SHIELDED (FCAW-G) WI
- Page 224 and 225: FLUX-CORED GAS-SHIELDED (FCAW-G) WI
- Page 226 and 227: SUBMERGED ARC (SAW) ELECTRODE Linco
- Page 228 and 229: SUBMERGED ARC (SAW) ELECTRODE Linco
- Page 230 and 231: SUBMERGED ARC (SAW) FLUX Lincolnwel
- Page 232 and 233: TIG (GTAW) CUT LENGTHS Lincoln® St
- Page 234 and 235: TIG (GTAW) CUT LENGTHS Lincoln® St
- Page 236 and 237: METAL-CORED (GMAW-C) WIRE Outershie
- Page 238 and 239: HARDFACING STICK (SMAW) ELECTRODE W
- Page 240 and 241: HARDFACING STICK (SMAW) ELECTRODE W
- Page 242 and 243: HARDFACING STICK (SMAW) ELECTRODE W
- Page 244 and 245: HARDFACING STICK (SMAW) ELECTRODE W
- Page 246 and 247: HARDFACING STICK (SMAW) ELECTRODE W
- Page 248 and 249: HARDFACING METAL-CORED GAS-SHIELDED
- Page 250 and 251: HARDFACING METAL-CORED (GMAW-C) WIR
- Page 252 and 253: HARDFACING FLUX-CORED SELF-SHIELDED
- Page 254 and 255: HARDFACING FLUX-CORED SELF-SHIELDED
- Page 256 and 257: HARDFACING FLUX-CORED SELF-SHIELDED
- Page 258 and 259: HARDFACING FLUX-CORED SELF-SHIELDED
- Page 260 and 261: HARDFACING FLUX-CORED SELF-SHIELDED
- Page 262 and 263: HARDFACING METAL-CORED SUBMERGED AR
- Page 264 and 265: HARDFACING METAL-CORED SUBMERGED AR
- Page 266 and 267: HARDFACING METAL-CORED SUBMERGED AR
- Page 268 and 269: HARDFACING METAL-CORED SUBMERGED AR
- Page 270 and 271: HARDFACING METAL-CORED SUBMERGED AR
- Page 274 and 275: HARDFACING METAL-CORED SUBMERGED AR
- Page 276 and 277: HARDFACING METAL-CORED SUBMERGED AR
- Page 278 and 279: HARDFACING SUBMERGED ARC (SAW) FLUX
- Page 280 and 281: HARDFACING SUBMERGED ARC (SAW) FLUX
- Page 282 and 283: MIG (GMAW) WIRE SuperGlaze Aluminum
- Page 284 and 285: MIG (GMAW) WIRE SuperGlaze Aluminum
- Page 286 and 287: MIG (GMAW) WIRE SuperGlaze Aluminum
- Page 288 and 289: SuperGlaze ® MIG (GMAW) WIRE Alumi
- Page 290 and 291: TIG (GTAW) CUT LENGTHS SuperGlaze A
- Page 292 and 293: ALUMINUM & CAST IRON CONSUMABLES No
- Page 294 and 295: PIPELINER ® STICK (SMAW) ELECTRODE
- Page 296 and 297: PIPELINER ® STICK (SMAW) ELECTRODE
- Page 298 and 299: PIPELINER ® STICK (SMAW) ELECTRODE
- Page 300 and 301: PIPELINER ® STICK (SMAW) ELECTRODE
- Page 302 and 303: PIPELINER ® STICK (SMAW) ELECTRODE
- Page 304 and 305: Pipeliner® Welding Positions All P
- Page 306 and 307: PIPELINER ® FLUX-CORED SELF-SHIELD
- Page 308 and 309: PIPELINER ® FLUX-CORED GAS-SHIELDE
- Page 310 and 311: PIPELINER ® FLUX-CORED GAS-SHIELDE
- Page 312 and 313: PIPELINER ® CONSUMABLES Electrode
- Page 314 and 315: PIPELINER ® CONSUMABLES Electrode
- Page 316 and 317: PIPELINER ® CONSUMABLES EN and ISO
- Page 318 and 319: Agency Approvals NOTE: Approvals ar
- Page 320 and 321: PIPELINER ® CONSUMABLES Notes 318
Typical Applications<br />
HARDFACING METAL-CORED SUBMERGED ARC (SAW) ELECTRODE<br />
Lincore®<br />
423Cr<br />
Caster rolls Metal-cored wire with a higher chrome deposit<br />
than Lincore ® 423L for improved corrosion<br />
resistance<br />
Recommended Flux<br />
Primary Flux (1)<br />
802<br />
(1) 802 and 860 standard flux are not sized for semiautomatic applications; however, they can be ordered in special sizing by<br />
contacting your <strong>Lincoln</strong> <strong>Electric</strong> representative.<br />
Roll Rebuilding - Metal-to-Metal<br />
Key Features<br />
DIAMETERS / PACKAGING<br />
Diameter 50 lb (22.7 kg)<br />
600 lb (272 kg)<br />
Coil<br />
Speed-Feed ® in (mm)<br />
Drum<br />
3/32 (2.4)<br />
EDS18553<br />
1/8 (3.2)<br />
EDS18554 ED018557<br />
MECHANICAL PROPERTIES (1)<br />
Rockwell Hardness (R C )<br />
DEPOSIT COMPOSITION (1)<br />
With Recommended Neutral Flux<br />
%C %Mn %Si %Cr %Ni %Mo %V<br />
41-47<br />
0.15 1.20 0.40 13.50 2.00 1.00 0.15<br />
TYPICAL OPERATING PROCEDURES<br />
Diameter, Polarity<br />
Wire Feed Speed Voltage Approx. Current Deposition Rate<br />
ESO - in (mm)<br />
m/min (in/min) (Volts)<br />
(Amps)<br />
kg/hr (lb/hr)<br />
3/32 in (2.4 mm), DC+<br />
1-1/2 (38)<br />
1.7 (65)<br />
3.0 (120)<br />
4.4 (175)<br />
24<br />
28<br />
31<br />
250<br />
350<br />
450<br />
2.7 (6.0)<br />
5.0 (11.0)<br />
7.3 (16.0)<br />
1/8 in (3.2 mm), DC+<br />
1-5/8 (40)<br />
1.5 (60)<br />
2.5 (100)<br />
3.6 (140)<br />
26<br />
28<br />
30<br />
375<br />
540<br />
640<br />
4.5 (9.9)<br />
7.5 (16.5)<br />
10.5 (23.1)<br />
IMPORTANT: SPECIAL VENTILATION AND/OR EXHAUST REQUIRED<br />
Fumes from the normal use of some welding products can contain significant quantities of components - such as chromium and manganese - which can lower the 5.0 mg/m3 maximum exposure guideline for general welding fume.<br />
BEFORE USE, READ AND UNDERSTAND THE MATERIAL SAFETY DATA SHEET (MSDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER.<br />
(1) Composition and properties depend upon dilution. Single layer deposit properties depend upon base metal and/or build-up material.<br />
WELDING CONSUMABLES CATALOG ı 271