This Rigger's Handbook is dedicated to Theodore C - Igor Chudov

More documents

Recommendations

Info

Clevises Material: C-1035 and SA-182-F-11 in stock Threads: U.N.C. Class 2B, Right or Left Hand Finish: Self-Colored, Galvanized, Plated Options: Stainless Steel; Other Alloys; Special Threading Maximum working loads have been established with a safety factor of 5:1 using the maximum pin diameter, the resulting net area of the eye at the pin hole, and the expected ultimate tensile strength of C-1035 steel. The maximum tap size (U dimension) shown in Table I is for reference purposes only. It should be used only to determine the largest tap diameter the clevis can accommodate without considering the pin diameter. Use Table II to select the proper combination of tap size and pin diameter for any given size of clevis. Clevis sizes in Table II for any given tap size and pin diameter combination are based upon the net area of the eye at the pin hole being equal to or greater than 125% of the net area at the minor diameter of a round rod without upset ends, threaded Unified National Coarse Series. For any combination of tap size and pin diameter shown, the pin in double shear will develop the strength of the rod if both the rod and pin are made from steel having the same physical properties. The pin must be investigated for bending, however; and if inadequate, a larger diameter pin selected. Pins supplied with clevises by Cleveland City Forge are made from steel having a minimum ultimate tensile strength of 58,000 pounds per square inch, unless otherwise specified. If the pin is made from steel with physical properties lower in value than the steel used for the rod, the pin may not develop the strength of the rod in either shear or bending; requiring a larger diameter pin. Some combinations of tap size and pin diameter shown will not develop the maximum working load of the clevis shown in Table I. Selection of the rod and pin, the material from which both are made, as well as the clevis size adequate to meet the required design load is the responsibility of the purchaser or user. Load imposed upon the clevis should not exceed the maximum working load values shown in Table I. DIAMETER OF TAP – Inches HEADQUARTERS: 55 James E. Casey Drive • Buffalo, NY 14206 PHONE: 716.826.2636 FAX: 716.826.4412 www.hanessupply.com 92 U N YOUR SLING AND RIGGING SPECIALIST W P D T A T TABLE I STANDARD CLEVIS DIMENSIONS – Inches MAX. WORKING WGT. CLEVIS D N U W TOLERANCE A P LOAD EACH NO. MAX. MAX. KIPS LBS. 2 1-7/16 5/8 5/8 1-1/16 5/16 + 1/32 - 0 3-9/16 3/4 3.5 1 2-1/2 2-1/2 1-1/8 7/8 1-1/4 5/16 + 1/32 - 0 4 1-1/2 7.5 2-1/2 3 3 1-1/4 1-3/8 1-1/2 1/2 + 1/32 - 1/32 5-1/16 1-3/7 15 4 3-1/2 3-1/2 1-1/2 1-1/2 1-3/4 1/2 + 1/16 - 1/16 6 2 18 6 4 4 1-3/4 1-3/4 2 1/2 + 1/16 - 1/16 5-15/16 2-1/4 21 8 5 5 2-1/4 2-1/8 2-1/2 5/8 + 3/32 - 0 7 2-1/2 37.5 16 6 6 2-3/4 2-1/2 3 3/4 + 3/32 - 0 8 3 54 26 7 7 3 3 3-1/2 7/8 + 1/8 - 1/16 9 3-3/4 68.5 36 8 8 4 4 4 1-1/2 + 1/8 - 1/16 10-1/8 4-1/4 135 90 TABLE II DIAMETER OF PIN – Inches 1/2 5/8 3/4 7/8 1 1¼ 1½ 1¾ 2 2¼ 2½ 2¾ 3 3¼ 3½ 3¾ 4 4¼ 3/8 2 2 2 1/2 2 2 2 5/8 2 2 2 2½ 2½ 2½ 2½ 3/4 2½ 2½ 2½ 2½ 2½ 7/8 2½ 2½ 2½ 3 1 3 3 3 3 1-1/8 3 3 3 3 3½ 1-1/4 3 3 3 3 3½ 1-3/8 3 3 3½ 3½ 4 1-1/2 3½ 3½ 4 4 5 1-5/8 4 4 4 5 5 5 1-3/4 4 5 5 5 5 1-7/8 5 5 5 5 5 2 5 5 5 5 5 6 6 2-1/8 5 5 6 6 6 6 2-1/4 6 6 6 6 6 7 7 2-3/8 6 6 6 6 7 7 7 7 2-1/2 6 6 6 7 7 7 7 7 2-5/8 7 7 7 7 7 8 2-3/4 7 7 7 7 8 8 2-7/8 7 8 8 8 8 8 8 8 3 7 8 8 8 8 8 8 8 3-1/8 8 8 8 8 8 8 8 3-1/4 8 8 8 8 8 8 8 3-3/8 8 8 8 8 8 8 8 3-1/2 8 8 8 8 8 8 3-5/8 8 8 8 8 8 3-3/4 8 8 8 8 3-7/8 8 8 8 4 8 8
YOUR SLING AND RIGGING SPECIALIST A-350 G-3315 S-3316 A-378 HOOKS • SNAP • REPLACEMENT • SORTING • FORGED ALLOY STEEL through 3/4". • Wide throat to take heavy thimbles *Ultimate Load is 5 times Safe Working Load. †When ordering, EYE diameter ("C") should be specified. SLIDING CHOKER HOOK with LATCH • Pressed steel latches and stainless steel springs, bolts and nuts. • Safe Working Loads shown are based on Ultimate Load that is 4 times the Safe Working Load. • Easily attached to any hoist with welded link load chain and roller chain or wire rope with suitable end fitting. • Spring latch, latch bolt with self locking nut – stainless steel. Nuts cadmium plated brass. • For chain and electric hoists with swivel jaw-forged. HEADQUARTERS: 55 James E. Casey Drive • Buffalo, NY 14206 PHONE: 716.826.2636 FAX: 716.826.4412 www.hanessupply.com 93 Hooks SLIDING CHOKER HOOKS Quenched & Tempered SINGLE EIGHT SAFE PART PART WORKING DIMENSIONS (IN.) WEIGHT ROPE ROPE LOAD* EACH SIZE SIZE (LBS.) A C E L (LBS.) 3/8 – 2,500 2-1/16 5/8 5/8 4-9/32 .77 1/2 1/8 3,300 2-1/4 3/4 25/32 4-31/32 1.19 5/8† 3/16 5,000 3-1/16 3/4 OR 1 5/16 6-3/8 2.89 3/4† 1/4 8,000 3-3/8 1 OR 1-7/16 1-5/32 7-21/32 5.00 • Deep straight throat permits efficient handling of flat plates or large cylindrical shapes. • The long tapered point allow easy grab in rings, pear links, eye bolts or lifting holes. • Ultimate load is 5 times the Safe Working Load. SORTING HOOK with HANDLE SNAP HOOKS Forged Steel, Quenched & Tempered SAFE INSIDE HOOK WORKING DIAM. THROAT LENGTH WEIGHT SIZE LOAD OF EYE OPENING OVERALL POUNDS (IN.) (LBS.) (IN.) (IN.) (IN.) PER 100 7/16 750 3/4 3/4 3-15/16 23.25 9/16 1,000 1-1/8 13/16 4-3/4 48.25 REPLACEMENT HOOKS Quenched & Tempered WIDTH SIZE BETWEEN DIAM. OVERALL THROAT WEIGHT HOIST JAWS BOLT LENGTH OPENING EACH (TON) (IN.) (IN.) (IN.) (IN.) (LBS.) 1/2 9/16 3/8 6-1/8 31/32 1.25 1 11/16 7/16 7-11/16 1-1/8 2.61 SORTING HOOKS Forged Alloy Steel Quenched & Tempered Safe Working Load at Tip 2 Ton Safe Working Load at Bottom of Hook 7-1/2 Ton Overall Length 9-11/16" I.D. of Eye 1-3/8" Opening at Top of Hook 2-13/16" Radius at Bottom of Hook 5/8" Weight Each 6.42 Lbs.
Page 2 and 3:
This Rigger’s Handbook is dedicat
Page 4 and 5:
Table of Contents Hooks, Synthetic
Page 6 and 7:
Innovative Lifting Solutions TWIN-P
Page 8 and 9:
Twin-Path ® Slings TWIN-PATH ® SL
Page 10 and 11:
Twin-Path ® Covermax Slings (Polye
Page 12 and 13:
Twin-Path ® Eye and Eye Sling TWIN
Page 14 and 15:
Twin-Path ® Adjustable Bridle The
Page 16 and 17:
Wear Pads and Cut Protectors Wear p
Page 18 and 19:
Twin-Path ® Slings in Action TWIN-
Page 20 and 21:
Twin-Path ® Slings 7.14 Portions o
Page 22 and 23:
Twin-Path ® Slings K-Spec core yar
Page 24 and 25:
Single-Path Round Slings SINGLE PAT
Page 26 and 27:
Tri-Flex ® Sling Engineering PIN S
Page 28 and 29:
Tri-Flex ® Sling System Engineerin
Page 30 and 31:
Gator-Laid ® Cable-Laid Slings Ins
Page 32 and 33:
Gator-Flex ® Slings T&D Ultra-Flex
Page 34 and 35:
Gator-Flex ®/Twin-Flex ® Grommets
Page 36 and 37:
Mechanical Splice Flemish Eye Sling
Page 38 and 39:
Grommet Slings CABLE LAID GROMMET W
Page 40 and 41:
2 Leg Wire Rope Bridles No. 200 Ser
Page 42 and 43:
4 Leg Wire Rope Bridles No. 400 Ser
Page 44 and 45: Chain Sling Assembly GRADE 80 CHAIN
Page 46 and 47: Chain Slings The life and strength
Page 48 and 49: Chain Sling Saddle Rings ALLOWS ADJ
Page 50 and 51: Chain Slings - Grade 80 Alloy Safet
Page 52 and 53: Load Binders LOAD BINDER WARNINGS A
Page 54 and 55: Lebus ® Load Binders STANDARD RATC
Page 56 and 57: Nylon Web Slings BASIC SLING TYPES
Page 58 and 59: Nylon Web Slings 5.3 - ENVIRONMENTA
Page 60 and 61: Polyester Ratchet Assembly TRUCKER
Page 62 and 63: Manual Hoists - Puller CM PULLER CM
Page 64 and 65: Manual Hoists - LHH LHH HAND CHAIN
Page 66 and 67: Wire Mesh Slings LIKE A GIANT HAND.
Page 68 and 69: Rope Slings MANILA ROPE SLINGS Tabl
Page 70 and 71: Rope Specifications ROPE SPECIFICAT
Page 72 and 73: Winch Lines GUIDELINES FOR THE USE
Page 74 and 75: Winch Lines CLEANING Sometimes util
Page 76 and 77: MSI Products The MSI-7200 Dyna-Link
Page 78 and 79: Hilman Rollers 1. How much does the
Page 80 and 81: Wire Rope Clips CROSBY CLIP WARNING
Page 82 and 83: Master Link MASTER LINK • Alloy S
Page 84 and 85: Alloy Bolt-Type Shackles NOM. WORKI
Page 86 and 87: Alloy Shackles "WIDE BODY" SLING SA
Page 88 and 89: Synthetic Sling Hook WEB SLING HOOK
Page 90 and 91: Hoist Hooks S-319 SHANK HOOKS SEE A
Page 92 and 93: Sling and Hoist Hooks S-320 EYE HOO
Page 96 and 97: Chain Hooks M806A CM ALLOY CLEVIS T
Page 98 and 99: Wedge Sockets "THE TERMINATOR" Cros
Page 100 and 101: Hook & Hook Turnbuckles HG-223 HOOK
Page 102 and 103: Eye & Eye Turnbuckles HG-226 EYE &
Page 104 and 105: Wire Rope Thimbles STANDARD WIRE RO
Page 106 and 107: Spelter Sockets G-416 GROOVED OPEN
Page 108 and 109: Open Swage Sockets E B F L A N OPEN
Page 110 and 111: Swage Buttons / Socket Compound •
Page 112 and 113: Right Eye Bolts More than one eye b
Page 114 and 115: Eye Bolts A E G F H SEE APPLICATION
Page 116 and 117: Hoist Rings ACTEK SWIVEL (SAFETY) H
Page 118 and 119: Lifting Clamps IPUZ vertical liftin
Page 120 and 121: Swivels S-1 JAW & HOOK S-3 JAW & EY
Page 122 and 123: Swaged Sockets In mechanically swag
Page 124 and 125: Wire Rope ROTATION RESISTANT WIRE R
Page 126 and 127: Wire Ropes ABRASION RESISTANCE FATI
Page 128 and 129: Wire Ropes INSPECTION - THE KEY TO
Page 130 and 131: Wire Ropes COMMON WIRE ROPE ABUSES
Page 132 and 133: Wire Ropes While there is a possibi
Page 134 and 135: Wire Ropes ROPE STRENGTH AND DESIGN
Page 136 and 137: Basic Lift Engineering EFFECT OF AN
Page 138 and 139: General Information In reeving a pa
Page 140 and 141: General Information The Rated Load
Page 142 and 143: General Information DEFINITIONS Rat
Page 144 and 145:
Lift Engineering FINDING THE HYPOTE
Page 146 and 147:
USA Standard Crane Hand Signals Use
Page 148:
One of the foremost leaders in the
show all

This Rigger's Handbook is dedicated to Theodore C - Igor Chudov

Create successful ePaper yourself

Delete template?

Save as template?