This Rigger's Handbook is dedicated to Theodore C - Igor Chudov

More documents

Recommendations

Info

Synthetic Sling Hook WEB SLING HOOK The Web Sling hook, originally designed for 2-Ply Web slings, can also be used with Round Slings as long as the Working Load Limit ratings are compatible. The new hook incorporates the following features: Eye is desigend with a wide beam surface which: • Eliminates bunching effects • Reduces sling tendency to slide. • Allows a better load distribution on internal fibers. Each hook has a Product Identification Code (PIC) for material traceability along with a working load limit. Hooks available in sizes 1-1/2 (1"), 3 (2"), and 5 (3") tons. All alloy construction. Design factor of 5 to 1. Fatigue rated to 20,000 cycles at 1-1/2 times the Working Load Limit. HEADQUARTERS: 55 James E. Casey Drive • Buffalo, NY 14206 PHONE: 716.826.2636 FAX: 716.826.4412 www.hanessupply.com 86 WS-320 A WEB SLING HOOK WEB SLING ROUND WORKING S-4320 NOMINAL SLING LOAD HOOK WS-320 A WSL-320 A REPLACEMENT SIZE SIZE LIMIT* I.D. S.C WITH LATCH LATCH KIT (IN.) (NUMBER) (TONS) CODE STOCK NO. STOCK NO. STOCK NO. 1" 1 1-1/2 FA 1022701 1022706 1096374 2" 2 3 HA 1022712 1022717 1096468 3" 3 5 IA 1022723 1022728 1096515 WEB SLING ROUND WORKING DIMENSIONS NOMINAL SLING LOAD (IN.) WEIGHT SIZE SIZE LIMIT* EACH (IN.) (NUMBER) (TONS) A B C D F G H J K L M N O P Q T AA (LBS.) 1" 1 1-1/2 5.25 2.26 3.98 3.11 1.38 .84 .94 .93 .71 1.50 .63 .75 .91 2.24 1.01 .98 2.00 1.10 2" 2 3 7.11 3.66 5.31 3.97 1.63 1.13 1.32 1.13 .94 2.50 .85 1.13 1.09 2.82 1.69 1.16 2.00 2.86 3" 3 5 9.33 5.13 7.06 4.81 2.00 1.44 1.63 1.47 1.31 3.75 1.13 1.63 1.36 3.51 2.59 1.53 2.50 6.60 *Note: Proof load is 2-1/2 times Working Load Limit. Average straightening load (ultimate load) is 5 time Working Load Limit. YOUR SLING AND RIGGING SPECIALIST
YOUR SLING AND RIGGING SPECIALIST SLING AND HOIST HOOKS WARNINGS AND APPLICATION INSTRUCTIONS S-319 S-320 S-320N S-322 Important Safety Information – Read and Follow • A visual periodic inspection for cracks, nicks, wear, gouges and deformation as part of a comprehensive documented inspection program, should be conducted by trained personnel in compliance with the schedule in ANSI B30.10. • For hooks used in frequent load cycles or pulsating loads, the hook and threads should be periodically inspected by Magnetic Particle or Dye Penetrant. (Note: Some disassembly may be required.) • Never use a hook whose throat opening has been increased, or whose tip has been bent more than 10 degrees out of plane from the hook body, or is in any other way distorted or bent. Note: A latch will not work properly on a hook with a bent or worn tip. • Never use a hook that is worn beyond the limits shown in Figure 1. • Remove from service any hook with a crack, nick, or gouge. Hooks with a crack, nick or gouge shall be repaired by grinding lengthwise, following the contour of the hook, provided that the reduced dimension is within the limits shown in Figure 1. • Never repair, alter, rework, or reshape a hook by welding, heating, burning, or bending. • Never side load, back load, or tip load a hook. (See Figure 2) • Eye hooks, shank hooks and swivel hooks are designed to be used with wire rope or chain. Efficiency of assembly may be reduced when used with synthetic material. • Do not swivel the S-322 swivel hook while it is supporting a load. • The use of a latch may be mandatory by regulations or safety codes; e.g., OSHA, MSHA, ANSI/ASME B30, Insurance, etc. • Always make sure the hook supports the load. (See Figure 3) The latch must never support the load. (See Figure 4) • When placing two (2) sling legs in hook, make sure the angle from the vertical to the outermost leg is not greater than 45 degrees, and the included angle between the legs does not exceed 90 degrees.* (See Figure 5) • See ANSI/ASME B30.10 "Hooks" for additional information. *For two legged slings with angles greater than 90°, use an intermediate link such as a master link or bolt type shackle to collect the legs of the slings. The intermediate link can then be placed over the hook to provide an in-line load on the hook. This approach must also be used when using slings with three or more legs. HEADQUARTERS: 55 James E. Casey Drive • Buffalo, NY 14206 PHONE: 716.826.2636 FAX: 716.826.4412 www.hanessupply.com 87 Sling and Hoist Hooks • Loads may disengage from hook if proper procedures are not followed. • A failing load may cause serious injury or death. • See OSHA Rule 1926.550(g) for personnel hoisting by cranes or derricks. A 319, 320 or 322 hook with a PL Latch attached (when secured with the bolt, nut and pin) may be used for lifting personnel. • Threads may corrode and/or strip and drop the load. • Hook must always support the load. The load must never be supported by the latch. • Never apply more force than the hook's assigned Working Load Limit (WLL) rating. • Read and understand these instructions before using hook. ZONE B RIGHT 45° 45° 60° ZONE A 2/3 ZONE C WARNING ZONE A: REPAIR NOT REQUIRED ZONE B: 10% OF ORIGINAL DIMENSION ZONE C: 5% OF ORIGINAL DIMENSION ZONE D: SEE MINIMUM THREAD SIZE Side Load Back Load WRONG Tip Load WRONG Figure 1 Figure 2 ZONE A Figure 3 Figure 4 Figure 5 ZONE B 45° 45° 2/3 ZONE C 60° ZONE D
Page 2 and 3:
This Rigger’s Handbook is dedicat
Page 4 and 5:
Table of Contents Hooks, Synthetic
Page 6 and 7:
Innovative Lifting Solutions TWIN-P
Page 8 and 9:
Twin-Path ® Slings TWIN-PATH ® SL
Page 10 and 11:
Twin-Path ® Covermax Slings (Polye
Page 12 and 13:
Twin-Path ® Eye and Eye Sling TWIN
Page 14 and 15:
Twin-Path ® Adjustable Bridle The
Page 16 and 17:
Wear Pads and Cut Protectors Wear p
Page 18 and 19:
Twin-Path ® Slings in Action TWIN-
Page 20 and 21:
Twin-Path ® Slings 7.14 Portions o
Page 22 and 23:
Twin-Path ® Slings K-Spec core yar
Page 24 and 25:
Single-Path Round Slings SINGLE PAT
Page 26 and 27:
Tri-Flex ® Sling Engineering PIN S
Page 28 and 29:
Tri-Flex ® Sling System Engineerin
Page 30 and 31:
Gator-Laid ® Cable-Laid Slings Ins
Page 32 and 33:
Gator-Flex ® Slings T&D Ultra-Flex
Page 34 and 35:
Gator-Flex ®/Twin-Flex ® Grommets
Page 36 and 37:
Mechanical Splice Flemish Eye Sling
Page 38 and 39: Grommet Slings CABLE LAID GROMMET W
Page 40 and 41: 2 Leg Wire Rope Bridles No. 200 Ser
Page 42 and 43: 4 Leg Wire Rope Bridles No. 400 Ser
Page 44 and 45: Chain Sling Assembly GRADE 80 CHAIN
Page 46 and 47: Chain Slings The life and strength
Page 48 and 49: Chain Sling Saddle Rings ALLOWS ADJ
Page 50 and 51: Chain Slings - Grade 80 Alloy Safet
Page 52 and 53: Load Binders LOAD BINDER WARNINGS A
Page 54 and 55: Lebus ® Load Binders STANDARD RATC
Page 56 and 57: Nylon Web Slings BASIC SLING TYPES
Page 58 and 59: Nylon Web Slings 5.3 - ENVIRONMENTA
Page 60 and 61: Polyester Ratchet Assembly TRUCKER
Page 62 and 63: Manual Hoists - Puller CM PULLER CM
Page 64 and 65: Manual Hoists - LHH LHH HAND CHAIN
Page 66 and 67: Wire Mesh Slings LIKE A GIANT HAND.
Page 68 and 69: Rope Slings MANILA ROPE SLINGS Tabl
Page 70 and 71: Rope Specifications ROPE SPECIFICAT
Page 72 and 73: Winch Lines GUIDELINES FOR THE USE
Page 74 and 75: Winch Lines CLEANING Sometimes util
Page 76 and 77: MSI Products The MSI-7200 Dyna-Link
Page 78 and 79: Hilman Rollers 1. How much does the
Page 80 and 81: Wire Rope Clips CROSBY CLIP WARNING
Page 82 and 83: Master Link MASTER LINK • Alloy S
Page 84 and 85: Alloy Bolt-Type Shackles NOM. WORKI
Page 86 and 87: Alloy Shackles "WIDE BODY" SLING SA
Page 90 and 91: Hoist Hooks S-319 SHANK HOOKS SEE A
Page 92 and 93: Sling and Hoist Hooks S-320 EYE HOO
Page 94 and 95: Clevises Material: C-1035 and SA-18
Page 96 and 97: Chain Hooks M806A CM ALLOY CLEVIS T
Page 98 and 99: Wedge Sockets "THE TERMINATOR" Cros
Page 100 and 101: Hook & Hook Turnbuckles HG-223 HOOK
Page 102 and 103: Eye & Eye Turnbuckles HG-226 EYE &
Page 104 and 105: Wire Rope Thimbles STANDARD WIRE RO
Page 106 and 107: Spelter Sockets G-416 GROOVED OPEN
Page 108 and 109: Open Swage Sockets E B F L A N OPEN
Page 110 and 111: Swage Buttons / Socket Compound •
Page 112 and 113: Right Eye Bolts More than one eye b
Page 114 and 115: Eye Bolts A E G F H SEE APPLICATION
Page 116 and 117: Hoist Rings ACTEK SWIVEL (SAFETY) H
Page 118 and 119: Lifting Clamps IPUZ vertical liftin
Page 120 and 121: Swivels S-1 JAW & HOOK S-3 JAW & EY
Page 122 and 123: Swaged Sockets In mechanically swag
Page 124 and 125: Wire Rope ROTATION RESISTANT WIRE R
Page 126 and 127: Wire Ropes ABRASION RESISTANCE FATI
Page 128 and 129: Wire Ropes INSPECTION - THE KEY TO
Page 130 and 131: Wire Ropes COMMON WIRE ROPE ABUSES
Page 132 and 133: Wire Ropes While there is a possibi
Page 134 and 135: Wire Ropes ROPE STRENGTH AND DESIGN
Page 136 and 137: Basic Lift Engineering EFFECT OF AN
Page 138 and 139:
General Information In reeving a pa
Page 140 and 141:
General Information The Rated Load
Page 142 and 143:
General Information DEFINITIONS Rat
Page 144 and 145:
Lift Engineering FINDING THE HYPOTE
Page 146 and 147:
USA Standard Crane Hand Signals Use
Page 148:
One of the foremost leaders in the
show all

This Rigger's Handbook is dedicated to Theodore C - Igor Chudov

Create successful ePaper yourself

Delete template?

Save as template?