This Rigger's Handbook is dedicated to Theodore C - Igor Chudov

More documents

Recommendations

Info

Swage Buttons / Socket Compound • Low carbon steel • Spherodize annealed • Quality controlled • Economical to use A multi-purpose fitting for many swaging applications. Manufactured from a special analysis high quality, low carbon steel, and later heat treated. They are precision made with constant quality control checks throughout all stages of manufacturing to assure the best in quality and performance. A D C E B BEFORE SWAGE AFTER SWAGE S-409 SWAGE BUTTONS ROPE DIMENSIONS (IN) ITEM DIAMETER A B C D E 1 SB 1/8 27/64 1/2 .141 3/8 39/64 2 SB 5/32 1/2 39/64 .172 7/16 23/32 3 SB 3/16 9/16 45/64 .203 1/2 27/32 4 SB 7/32 41/64 13/16 .234 9/16 31/32 5 SB 1/4 41/64 1-1/16 .296 9/16 1-13/64 6 SB 9/32 49/64 1-1/32 .313 11/16 1-13/64 7 SB 5/16 27/32 1-1/8 .358 3/4 1-21/64 8 SB 3/8 27/32 1-31/64 .421 3/4 1-11/16 9 SB 7/16 1-1/8 1-5/8 .484 1 1-15/16 10 SB 1/2 1-17/64 1-57/64 .547 1-1/8 2-11/64 11 SB 9/16 1-13/32 2-1/64 .609 1-1/4 2-13/32 12 SB 5/8 1-35/64 2-27/64 .672 1-3/8 2-57/64 13 SB 3/4 1-11/16 2-47/64 .796 1-1/2 3-1/4 14 SB 7/8 1-31/32 3-17/64 .936 1-3/4 3-55/64 15 SB 1 2-1/4 3-43/64 1.061 2 4-23/64 16 SB 1-1/8 2-17/32 4-3/64 1.188 2-1/4 4-23/64 17 SB 1-1/4 2-13/16 4-37/64 1.328 2-1/2 5-27/64 18 SB 1-3/8 3-3/32 5-5/64 1.453 2-3/4 6-1/32 19 SB 1-1/2 3-3/8 5-15/32 1.578 3 6-33/64 NOTE: Length is measured from outside end of terminal. WIRELOCK ® - RESIN FOR SPELTER SOCKETS W416-7 • Ideal for on-site applications • Improved fatigue life • For use on 416 & 417 Spelter Sockets only • 100% termination efficiency • Temperature operating range from -65°F to +240°F • One Booster pack needed if pouring temperature is 35°F to 48°F • Two Booster packs needed if pouring temperature is 27°F to 35°F APPROXIMATE U.S. MEASUREMENTS 250cc Kit 1 Cup 500cc Kit 1 Pint 1,000cc Kit 1 Quart NATO NUMBERS 100cc 8030-21-902-1823 250cc 8030-21-902-1824 500cc 8030-21-902-1825 1,000cc 8030-21-902-1826 Witnessed and tested by American Bureau of Shipping (ABS) HEADQUARTERS: 55 James E. Casey Drive • Buffalo, NY 14206 PHONE: 716.826.2636 FAX: 716.826.4412 www.hanessupply.com 108 YOUR SLING AND RIGGING SPECIALIST AMOUNT OF WIRELOCK ® REQUIRED WIRE ROPE SIZE (IN.) WIRELOCK ® REQUIRED (CC) WIRE ROPE SIZE (IN.) WIRELOCK® REQUIRED (CC) 1/4 9 1-3/4 700 5/16 17 1-7/8 700 3/8 17 2 1265 7/16 35 2-1/8 1265 1/2 35 2-1/4 1410 9/16 52 2-3/8 1410 5/8 52 2-1/2 1830 3/4 86 2-5/8 1830 7/8 125 2-3/4 2250 1 160 3 3160 1-1/8 210 3-1/4 3795 1-1/4 350 3-1/2 4920 1-3/8 350 3-3/4 5980 1-1/2 420 4 7730 1-5/8 495 W416-7 KITS BOOSTER KIT KITS STOCK WT. EACH PACK SIZE PER CASE NO. (LBS.) STOCK NO. 100 CC 20 1039602 .62 1039603 250 CC 12 1039604 1.25 1039605 500 CC 12 1039606 2.54 1039607 1000 CC 12 1039608 4.59 1039609 2000 CC 12 1039610 9.00 1039611
YOUR SLING AND RIGGING SPECIALIST FORGED EYE BOLT WARNINGS AND APPLICATION INSTRUCTIONS Regular Nut Eye Bolt G-291 Shoulder Nut Eye Bolt G-277 Machinery Eye Bolt G-279 Important Safety Information – Read and Follow Inspection/Maintenance Safety • Always inspect eye bolt before use. • Never use eye bolt that shows signs of wear or damage. • Never use eye bolt if eye or shank is bent or elongated. • Always be sure threads on shank and receiving holes are clean. • Never machine, grind, or cut eye bolt. Assembly Safety • Never exceed load limits specified in Table I. • Never use regular nut eye bolts for angular lifts. • Always use shoulder nut eye bolts (or machinery eye bolts) for angular lifts. • For angular lifts, adjust working load as follows: DIRECTION OF PULL ADJUSTED WORKING LOAD 45 degrees 30% of rated working load 90 degrees 25% of rated working load • Never undercut eye bolt to seat shoulder against the load. • Always countersink receiving hole or use washers to seat shoulder. • Always screw eye bolt down completely for proper seating. • Always tighten nuts securely against the load. HEADQUARTERS: 55 James E. Casey Drive • Buffalo, NY 14206 PHONE: 716.826.2636 FAX: 716.826.4412 www.hanessupply.com 109 Eye Bolts • Loads may slip or fall if proper eye bolt assembly and lifting procedures are not used. • A falling load can seriously injure or kill. • Read, understand and follow all eye bolt safety information and diagrams presented here. Size (in.) TABLE I (IN-LINE LOAD) Working Load Limit (lbs.) 1/4 650 5/16 1200 3/8 1550 1/2 2600 5/8 5200 3/4 7200 7/8 10600 1 13300 1-1/4 21000 1-1/2 24000 • Thickness of spacers must exceed this distance between the bottom of the load and the last thread of the eye bolt. WARNING Shoulder Nut Eye Bolt – Installation for Angular Loading • The threaded shank must protrude through the load sufficiently to allow full engagement of the nut. • If the eye bolt protrudes so far through the load that the nut cannot be tightened securely against the load, use properly sized washers to take up the excess space BETWEEN THE NUT AND THE LOAD. • Place washers or spacers between nut and load so that when the nut is tightened securely, the shoulder is secured flush against the load surface.
Page 2 and 3:
This Rigger’s Handbook is dedicat
Page 4 and 5:
Table of Contents Hooks, Synthetic
Page 6 and 7:
Innovative Lifting Solutions TWIN-P
Page 8 and 9:
Twin-Path ® Slings TWIN-PATH ® SL
Page 10 and 11:
Twin-Path ® Covermax Slings (Polye
Page 12 and 13:
Twin-Path ® Eye and Eye Sling TWIN
Page 14 and 15:
Twin-Path ® Adjustable Bridle The
Page 16 and 17:
Wear Pads and Cut Protectors Wear p
Page 18 and 19:
Twin-Path ® Slings in Action TWIN-
Page 20 and 21:
Twin-Path ® Slings 7.14 Portions o
Page 22 and 23:
Twin-Path ® Slings K-Spec core yar
Page 24 and 25:
Single-Path Round Slings SINGLE PAT
Page 26 and 27:
Tri-Flex ® Sling Engineering PIN S
Page 28 and 29:
Tri-Flex ® Sling System Engineerin
Page 30 and 31:
Gator-Laid ® Cable-Laid Slings Ins
Page 32 and 33:
Gator-Flex ® Slings T&D Ultra-Flex
Page 34 and 35:
Gator-Flex ®/Twin-Flex ® Grommets
Page 36 and 37:
Mechanical Splice Flemish Eye Sling
Page 38 and 39:
Grommet Slings CABLE LAID GROMMET W
Page 40 and 41:
2 Leg Wire Rope Bridles No. 200 Ser
Page 42 and 43:
4 Leg Wire Rope Bridles No. 400 Ser
Page 44 and 45:
Chain Sling Assembly GRADE 80 CHAIN
Page 46 and 47:
Chain Slings The life and strength
Page 48 and 49:
Chain Sling Saddle Rings ALLOWS ADJ
Page 50 and 51:
Chain Slings - Grade 80 Alloy Safet
Page 52 and 53:
Load Binders LOAD BINDER WARNINGS A
Page 54 and 55:
Lebus ® Load Binders STANDARD RATC
Page 56 and 57:
Nylon Web Slings BASIC SLING TYPES
Page 58 and 59:
Nylon Web Slings 5.3 - ENVIRONMENTA
Page 60 and 61: Polyester Ratchet Assembly TRUCKER
Page 62 and 63: Manual Hoists - Puller CM PULLER CM
Page 64 and 65: Manual Hoists - LHH LHH HAND CHAIN
Page 66 and 67: Wire Mesh Slings LIKE A GIANT HAND.
Page 68 and 69: Rope Slings MANILA ROPE SLINGS Tabl
Page 70 and 71: Rope Specifications ROPE SPECIFICAT
Page 72 and 73: Winch Lines GUIDELINES FOR THE USE
Page 74 and 75: Winch Lines CLEANING Sometimes util
Page 76 and 77: MSI Products The MSI-7200 Dyna-Link
Page 78 and 79: Hilman Rollers 1. How much does the
Page 80 and 81: Wire Rope Clips CROSBY CLIP WARNING
Page 82 and 83: Master Link MASTER LINK • Alloy S
Page 84 and 85: Alloy Bolt-Type Shackles NOM. WORKI
Page 86 and 87: Alloy Shackles "WIDE BODY" SLING SA
Page 88 and 89: Synthetic Sling Hook WEB SLING HOOK
Page 90 and 91: Hoist Hooks S-319 SHANK HOOKS SEE A
Page 92 and 93: Sling and Hoist Hooks S-320 EYE HOO
Page 94 and 95: Clevises Material: C-1035 and SA-18
Page 96 and 97: Chain Hooks M806A CM ALLOY CLEVIS T
Page 98 and 99: Wedge Sockets "THE TERMINATOR" Cros
Page 100 and 101: Hook & Hook Turnbuckles HG-223 HOOK
Page 102 and 103: Eye & Eye Turnbuckles HG-226 EYE &
Page 104 and 105: Wire Rope Thimbles STANDARD WIRE RO
Page 106 and 107: Spelter Sockets G-416 GROOVED OPEN
Page 108 and 109: Open Swage Sockets E B F L A N OPEN
Page 112 and 113: Right Eye Bolts More than one eye b
Page 114 and 115: Eye Bolts A E G F H SEE APPLICATION
Page 116 and 117: Hoist Rings ACTEK SWIVEL (SAFETY) H
Page 118 and 119: Lifting Clamps IPUZ vertical liftin
Page 120 and 121: Swivels S-1 JAW & HOOK S-3 JAW & EY
Page 122 and 123: Swaged Sockets In mechanically swag
Page 124 and 125: Wire Rope ROTATION RESISTANT WIRE R
Page 126 and 127: Wire Ropes ABRASION RESISTANCE FATI
Page 128 and 129: Wire Ropes INSPECTION - THE KEY TO
Page 130 and 131: Wire Ropes COMMON WIRE ROPE ABUSES
Page 132 and 133: Wire Ropes While there is a possibi
Page 134 and 135: Wire Ropes ROPE STRENGTH AND DESIGN
Page 136 and 137: Basic Lift Engineering EFFECT OF AN
Page 138 and 139: General Information In reeving a pa
Page 140 and 141: General Information The Rated Load
Page 142 and 143: General Information DEFINITIONS Rat
Page 144 and 145: Lift Engineering FINDING THE HYPOTE
Page 146 and 147: USA Standard Crane Hand Signals Use
Page 148: One of the foremost leaders in the
show all

This Rigger's Handbook is dedicated to Theodore C - Igor Chudov

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?