Programm Photovoltaik Ausgabe 2009 ... - Bundesamt für Energie BFE
Programm Photovoltaik Ausgabe 2009 ... - Bundesamt für Energie BFE Programm Photovoltaik Ausgabe 2009 ... - Bundesamt für Energie BFE
3/3 Die Materialkompatibilitätstests umfassten Klimakammerprüfungen mit einer Auswahl an am Markt verfügbaren Materialien zu Herstellung von Solarlaminaten, sowie die Prüfung von elektrischen Bauteilen, welche in Kunststoff eingegossen waren (Vgl. Bild 2). Ferner wurden Tests zur Statik, zum Brandverhalten und zur Regendichtigkeit durchgeführt. Bild 2: mit Kunststoff umgossene Dioden nach Klimakammerprüfung Aufgrund der Erkenntnisse aus den internen Tests und Normprüfungen wurden neue Produktvarianten entworfen und mit der Erstellung entsprechender Produktkalkulationen begonnen. Diese sind zurzeit in Bearbeitung. Die Änderungen am ursprünglichen SmartTile Produktdesign sind insbesondere aufgrund der Anforderungen an das Brandverhalten von Dachelementen erforderlich. Bewertung 2008 und Ausblick 2009 Eine Beurteilung der Erfolge und Misserfolge des im August gestarteten SmartTile Projektes ist noch verfrüht. Als Ausblick für 2009 stehen die Themen Entwicklung einer neuen Lösungsvariante, deren Kalkulation, die Patentierung und der Beginn der Zertifizierungsprüfungen im Vordergrund. SmartTile, T. Szacsvay, 3S Swiss Solar Systems 189/290
- Page 142: 5/5 Figure 4: Maximum achievable sh
- Page 145 and 146: Project Goals The goal is the estab
- Page 147 and 148: Evaluation 2008 and Outlook 2009 L'
- Page 149 and 150: Project Goals NAPOLYDE industrials
- Page 151 and 152: � Organic large solar panel and
- Page 153 and 154: Materials such as the conductive ca
- Page 155 and 156: National and international collabor
- Page 157 and 158: Project Goals The aim of FULLSPECTR
- Page 159 and 160: In addition, every two years, the P
- Page 161 and 162: The table below show the change of
- Page 163 and 164: The table below shows the change of
- Page 165 and 166: 4. The UV-A tests with PMMA films c
- Page 167 and 168: Introduction / Project Goals The co
- Page 169 and 170: Fig. 4. Schematic illustration of a
- Page 172 and 173: THINPV Eidgenössisches Departement
- Page 174 and 175: 3/6 IR laser source Pumping line IR
- Page 176 and 177: 5/6 Figure 2: Scheme of a monolithi
- Page 178 and 179: PECNET Eidgenössisches Departement
- Page 180 and 181: 3/10 Projektziele Dieses Forschungs
- Page 182 and 183: 5/10 und mit Stichworten katalogisi
- Page 184 and 185: 7/10 einer Vorverpflichtung mit rel
- Page 186 and 187: 9/10 NanoPEC Partner IEA HIA Annex
- Page 188: Module und Gebäudeintegration T. S
- Page 191: Einleitung / Projektziele Obwohl be
- Page 195 and 196: Objectives The objective of this th
- Page 197 and 198: HOOC S C N N COO TBA K77: FULL SUNL
- Page 199 and 200: defect. In this task, the influence
- Page 201 and 202: Task 12. Combination of environment
- Page 204 and 205: Département fédéral de l’envir
- Page 206 and 207: 3/8 N° of modules Services 500 Can
- Page 208 and 209: 5/8 late the mismatch factor M and
- Page 210 and 211: 7/8 In CIS modules (WSG0036E075 of
- Page 212 and 213: Eidgenössisches Departement für U
- Page 214 and 215: 3/8 technologies still suffer of tr
- Page 216 and 217: 5/8 2.2.2 IV-translation applied to
- Page 218 and 219: 7/8 application of part 1 of the IE
- Page 220 and 221: Eidgenössisches Departement für U
- Page 222 and 223: 3/8 Durchgeführte Arbeiten und err
- Page 224 and 225: 5/8 P DC [W] Power P [kW] 100000 10
- Page 226 and 227: 7/8 �MPPTdyn in % �MPPTdyn in %
- Page 228 and 229: Eidgenössisches Departement für U
- Page 230 and 231: 3/8 Clearly, direct PV injection do
- Page 232 and 233: 5/8 � Development of two PV-input
- Page 234 and 235: 7/8 Figure 7: PV array of Ines faci
- Page 236: Internationale Koordination P. Hüs
- Page 239 and 240: Kurzbeschrieb des Projekts Task 1 u
- Page 241 and 242: Zwischen den beiden Datenquellen er
3/3<br />
Die Materialkompatibilitätstests umfassten Klimakammerprüfungen mit einer Auswahl an am Markt<br />
verfügbaren Materialien zu Herstellung von Solarlaminaten, sowie die Prüfung von elektrischen Bauteilen,<br />
welche in Kunststoff eingegossen waren (Vgl. Bild 2). Ferner wurden Tests zur Statik, zum<br />
Brandverhalten und zur Regendichtigkeit durchgeführt.<br />
Bild 2: mit Kunststoff umgossene Dioden nach Klimakammerprüfung<br />
Aufgrund der Erkenntnisse aus den internen Tests und Normprüfungen wurden neue Produktvarianten<br />
entworfen und mit der Erstellung entsprechender Produktkalkulationen begonnen. Diese sind zurzeit<br />
in Bearbeitung. Die Änderungen am ursprünglichen SmartTile Produktdesign sind insbesondere<br />
aufgrund der Anforderungen an das Brandverhalten von Dachelementen erforderlich.<br />
Bewertung 2008 und Ausblick <strong>2009</strong><br />
Eine Beurteilung der Erfolge und Misserfolge des im August gestarteten SmartTile Projektes ist noch<br />
verfrüht. Als Ausblick <strong>für</strong> <strong>2009</strong> stehen die Themen Entwicklung einer neuen Lösungsvariante, deren<br />
Kalkulation, die Patentierung und der Beginn der Zertifizierungsprüfungen im Vordergrund.<br />
SmartTile, T. Szacsvay, 3S Swiss Solar Systems<br />
189/290