Programm Photovoltaik Ausgabe 2009 ... - Bundesamt für Energie BFE

More documents

Recommendations

Info

7/8 SP6 – Process Analysis – Upscaling The manufacturing of nano-TiO2 in larger scale encountered a problem due to agglomeration of the titania particles during work-up, as shown in the TiO2 layer SEM pictures below: By reducing the concentrations involved, the issue was solved and only a small scaling up of a factor two was achieved. The dye solar cell modules have been sucessfully increased in size from 10 x 10 cm to 30 x 30 cm thanks to a new 70 x 50 cm precision screen printer acquired in 2008. Currently, the "30 x 30 cm pilot line" is in build-up allowing for faster production of these demonstration modules, starting in April 09. NAPOLYDE, T. Meyer, Solaronix 151/290
National and international collaboration From the nature of this project, most of the partners are international, such as ELCERAM in the Tchech Republic, SIEMENS & KONARKA in Germany, SOPRA & St-Gobain in France, BAR-ILAN University in Israel. A partnership with a large Swiss chemicals company has been tied up for the investigation of new materials and the feasibility of large scale manufacturing of monolithic modules using all printed active layers. A new Eureka program E!4413 LCSC with 3GSolar (Israel) has been launched, investigating the manufacturing of large area monolithic dye solar cell modules. Evaluation 2008 and Outlook <strong>2009</strong> In 2008 the processes for the monolithic module manufacturing were identified and analyzed, especially the carbon paste printing and laser scribing were looked at carefully, as we observed many failures during to these steps. Thanks to new equipments, the solar module up scaling to 30 x 30 cm in size was mastered. Difficulties were encountered for the production increase of the screen print nano- TiO2 paste and the agglomeration problem was only solved by cutting back the batch sizes. During <strong>2009</strong>, the up scaling of the monolithic module production to 30 x 30 cm will be completed with the arrival of the belt furnace in March 09. The aim is to make test cells / modules to be aged in artificial sunlight (light soaking) and also in low light conditions. Various demonstration samples (from a few cm 2 to up to 30 x 30 cm in size) will be produced for marketing and customer trials. References www.napolyde.org, www.myndsphere.com “Monolithic Dye Sensitized Solar Cell Modules" Toby Meyer , David Martineau, Asef Azam, Mike Scott and Andreas Meyer, Proceedings of the Nano-Sol-Net International Symposium: Trends in Organic Electronics and Hybrid Photovoltaics, Eforie Nord, Romania, June 12-14, 2008, edited by M.A. Gîr�u and M. Fahlman, Ovidius University Press, Constan�a 2008. NAPOLYDE, T. Meyer, Solaronix 152/290 8/8
Page 1:
Forschung, April 2009 Programm Phot
Page 4 and 5:
Programm Photovoltaik Ausgabe 2009
Page 6 and 7:
B. Ruhstaller, R. Häusermann, N. A
Page 8 and 9:
PROGRAMM PHOTOVOLTAIK Eidgenössisc
Page 10 and 11:
1. Programmschwerpunkte und anvisie
Page 12 and 13:
Eine zweite Kategorie von Projekten
Page 14 and 15:
Im Integrierten EU-Projekt ATHLET [
Page 16 and 17:
Figur 3: Prototyp eines monolithisc
Page 18 and 19:
SOLARMODULE UND GEBÄUDEINTEGRATION
Page 20 and 21:
BEGLEITENDE THEMEN Das PSI beteilig
Page 22 and 23:
Programme abgeschlossen. Die erste
Page 24 and 25:
Messkampagnen - Messkampagne Wittig
Page 26 and 27:
zielführend eingesetzt werden. Das
Page 28 and 29:
[43] P. Renaud, L. Perret, (pierre.
Page 30:
11. Verwendete Abkürzungen (inkl.
Page 33 and 34:
D. Güttler, S. Bücheler, S. Seyrl
Page 35 and 36:
Goals of the project The global pro
Page 37 and 38:
1.2. Comparison of ZnO and SiOx int
Page 39 and 40:
2. Processes 2.1. Microcrystalline
Page 41 and 42:
3.2. Amorphous/amorphous silicon ta
Page 43 and 44:
Fig.14: TEM cross section microcrys
Page 45 and 46:
EQE 1.0 0.8 0.6 0.4 0.2 12.4 11.7 1
Page 47 and 48:
4.7 Summary and perspectives for wo
Page 49 and 50:
Acknowledgements We thank all the P
Page 51 and 52:
Goals of the project The goals of t
Page 54 and 55:
Eidgenössisches Departement für U
Page 56:
3/3 on the front side. All the laye
Page 59 and 60:
Introduction / Project Goals Prior
Page 62 and 63:
Page 64 and 65:
3/4 Effective light trapping scheme
Page 66 and 67:
Département fédéral de l’envir
Page 68 and 69:
3/6 The Athlet consortium comprises
Page 70 and 71:
5/6 Large area thin-film silicon ce
Page 72 and 73:
Page 74 and 75:
3/4 Der verbesserte Lichteinfang is
Page 76 and 77:
Page 78 and 79:
3/5 Results Microstructure characte
Page 80:
5/5 Mechanical testing: The mechani
Page 83 and 84:
Introduction / Project goals The fo
Page 85 and 86:
Optimization of CdS chemical bath d
Page 87 and 88:
Fig. 5: J-V curve (left) and extern
Page 90 and 91:
Page 92 and 93:
3/7 Work performed and results achi
Page 94 and 95:
5/7 Fig. 3: Raman spectra recorded
Page 96:
7/7 Measurements of solar cells per
Page 99 and 100:
Introduction / project objectives T
Page 101 and 102:
Optimum Na dosage Sodium layer with
Page 103 and 104: application might become more impor
Page 105 and 106: In a second experiment the amount o
Page 108 and 109: Eidgenössisches Departement für U
Page 110 and 111: 3/9 After optimizing the In2S3 buff
Page 112 and 113: 5/9 Indium sulfide layer characteri
Page 114 and 115: 7/9 3) Semitransparent CIGS solar c
Page 116: 9/9 Steps towards multi-junction so
Page 119 and 120: Introduction / project objectives T
Page 121 and 122: Figure 2: SEM picture of laser-abla
Page 123 and 124: Introduction / project objectives T
Page 125 and 126: Work progress and achievements duri
Page 127 and 128: Furthermore, with a good reproducib
Page 129 and 130: Main achievements - The association
Page 131 and 132: Introduction Dye-sensitized solar c
Page 136 and 137: 3/4 So far, experiments were perfor
Page 140 and 141: 3/5 Tasks of the collaboration part
Page 142: 5/5 Figure 4: Maximum achievable sh
Page 145 and 146: Project Goals The goal is the estab
Page 147 and 148: Evaluation 2008 and Outlook 2009 L'
Page 149 and 150: Project Goals NAPOLYDE industrials
Page 151 and 152: � Organic large solar panel and
Page 153: Materials such as the conductive ca
Page 157 and 158: Project Goals The aim of FULLSPECTR
Page 159 and 160: In addition, every two years, the P
Page 161 and 162: The table below show the change of
Page 163 and 164: The table below shows the change of
Page 165 and 166: 4. The UV-A tests with PMMA films c
Page 167 and 168: Introduction / Project Goals The co
Page 169 and 170: Fig. 4. Schematic illustration of a
Page 172 and 173: THINPV Eidgenössisches Departement
Page 174 and 175: 3/6 IR laser source Pumping line IR
Page 176 and 177: 5/6 Figure 2: Scheme of a monolithi
Page 178 and 179: PECNET Eidgenössisches Departement
Page 180 and 181: 3/10 Projektziele Dieses Forschungs
Page 182 and 183: 5/10 und mit Stichworten katalogisi
Page 184 and 185: 7/10 einer Vorverpflichtung mit rel
Page 186 and 187: 9/10 NanoPEC Partner IEA HIA Annex
Page 188: Module und Gebäudeintegration T. S
Page 191 and 192: Einleitung / Projektziele Obwohl be
Page 194 and 195: ULTRALIGHT PHOTOVOLTAIC STRUCTURES
Page 196 and 197: 3/8 Task 2. Encapsulation of Si-bas
Page 198 and 199: 5/8 Figure 9: polyester/glass fiber
Page 200 and 201: 7/8 Figure 16: Flexible DSCmodule F
Page 202: Systemtechnik D. Chianese, N. Cereg
Page 205 and 206:
Aim of the project The aim of the
Page 207 and 208:
The short circuit current of each P
Page 209 and 210:
TEST cycle 11 In 2008 a new 15 mont
Page 211 and 212:
Evaluation 2008 and prospects for 2
Page 213 and 214:
1. Traceable performance measuremen
Page 215 and 216:
formed with two standard halogen la
Page 217 and 218:
3. Modelling and analysis (SP4) 3.1
Page 219 and 220:
Figure 3 shows a summary of the RR
Page 221 and 222:
Projektziele für 2008 � Fortfüh
Page 223 and 224:
Interessant ist die Beobachtung, da
Page 225 and 226:
Wechselrichtertests Im Bereich der
Page 227 and 228:
Stress limits for bypass diodes for
Page 229 and 230:
Objectives SoS-PV (Security of Supp
Page 231 and 232:
Finally, strategies for demand side
Page 233 and 234:
~ Mains terminal Synchronisation &
Page 235 and 236:
International collaboration SoS-PVi
Page 238 and 239:
Page 240 and 241:
The cumulative installed PV power i
Page 242:
5/5 Workshops Grid Parity & Beyond
Page 245 and 246:
Einleitung / Projektziele Die Ziele
Page 247 and 248:
Dank der Projektdatenbank vom Task
Page 249 and 250:
Nationale und internationale Zusamm
Page 251 and 252:
Einleitung Anfangs 2008 konnte die
Page 253 and 254:
Das Verfahren für Projektanträge
Page 255 and 256:
Skizze - nicht eintreten 13% Gesuch
Page 257 and 258:
Community Based Rural Income throug
Page 259 and 260:
Licht für Bildung und Entwicklung
Page 262 and 263:
Département fédéral de l’envir
Page 264 and 265:
3/6 SOUS-TÂCHE 2 « PLANIFICATION,
Page 266 and 267:
5/6 Conformément au plan de travai
Page 268 and 269:
Page 270 and 271:
3. Durchgeführte Arbeiten und erre
Page 272 and 273:
kg/m2 7 6 5 4 3 2 1 0 Fassadenaufst
Page 274 and 275:
Page 276 and 277:
3/5 Table 2: Sites used for benchma
Page 278:
5/5 Figure 2: Example of forecasted
Page 281 and 282:
2/6 Einleitung / Projektziele Der r
Page 283 and 284:
4/6 Die Technical Standards (TS) zu
Page 285 and 286:
6/6 Im Jahr 2008 neu publizierte No
Page 287 and 288:
Introduction and Goals PV ERA NET i
Page 289 and 290:
Operational Level The networking ac
Page 291 and 292:
Topical Areas: Complementarities, G
Page 293:
International Cooperation According
show all

Programm Photovoltaik Ausgabe 2009 ... - Bundesamt für Energie BFE

Create successful ePaper yourself

Delete template?

Save as template?