and Excluder Seals - Clark Seals, Ltd.
and Excluder Seals - Clark Seals, Ltd. and Excluder Seals - Clark Seals, Ltd.
Material Selection Polymer Mechanical Properties and Compatibility Base Polymer Nitrile Neoprene Material Code Mechanical Properties Temperature Range 4 Abrasion Resistance Compression Set Tear Resistance Resistance To: Cold Heat Oxidation Ozone Sunlight Aging Water Compatibility with Lubricants: Automatic Transmission Fluid E.P. Lubricants Grease Hydraulic Fluid Petroleum Base Lubricating Oils Engine Oil SAE 30 wt. SAE 10 wt. Gear Oil Super Gear Hypoid Gear Compatibility with Solvents: Aliphatic Hydrocarbons Aromatic Hydrocarbons Halogenated Solvents Ketones Compatibility with Acids: 20% Hydrochloric Acid Solution 30% Sulfuric Acid Solution Compatibility with Other Fluids: Alcohol Alkali Animal and Vegetable Oils Gasoline Water-Glycol Durometer Range: ® - -50°F to 250°F -45°C to 120°C G G F G G F G P G E G E E E E E E G G F P P F F E G E F E 65-90 N -40°F to 225°F -40°C to 105°C E F G F G E E E F G G E E G G G G G G F P P F E E G G F F 65-85 Polyacrylate P -20°F to 300°F -30°C to 150°C F F F F E E E G F E E E E E E E E G P P P P F F P P E P P 65-85 Silicone S -80°F to 400°F -60°C to 200°C P G P E E G E G G F P E P F E G F P P P P P F P G P G P G 65-80 Florocarbon (Viton ® ) V -30°F to 400°F -35°C to 200°C G E F F E E E E G E E E E E E E E E E E G P E E F F E E G 65-90 E - Excellent. G - Good for most applications. F - Fair, not recommended. P - Poor, do not use.
Products Sheave Seals ® are specifically designed for use with Timken’s ® TNASW and TNASWE tapered roller bearing assemblies. The Sheave Seals ® make the bearing assembly a “unitized” sealing unit. Excluder Seals ® are designed for tapered, cylindrical, and spherical roller bearings and for deep grooved, self-aligning, maximum capacity, and double-row ball bearings. They are designed to prevent dirt and debris from entering the bearing cavity. Spent grease can be flushed from the bearing cavity, promoting extended bearing life. Full Face CO and CN Excluder Seals ® are designed for radial ball bearings such as deep grooved, double row, maximum capacity, and angular contact as well as spherical and cylindrical roller bearings that already contain an integral seal or shield. Labyrinth Grease Retainer Seals are designed to retain grease in the tapered roller bearing cavity. Bore Plugs are designed to seal the housing bore and provide easy future access to the shaft. They retain grease and exclude contaminants. Excluder Seals ® and Sheave Seals ® are designed for grease lubricants. They are registered trademarks of Clark Seals Ltd. ® and are designed for tapered roller bearings. . TIMKEN ® is a registered trademark of The Timken Company ® . WARRANTY Clark Seals, Ltd. ® warrants its manufactured products to be free from defects in materials and workmanship for up to one full year from the date of purchase. The manufacturer’s obligation under this warranty is limited to replacing any returned seal which, upon inspection by the manufacturer, proves to be defective. We will not replace any seal that is defective due to abuse, alteration by others, accident, misapplication, improper installation, or normal wear and tear. The customer shall be responsible for all return shipping costs. Under no circumstance shall Clark Seals, Ltd. ® be liable for any amount in excess of the actual purchase price paid for the seals nor for cost of installation of replacement parts. This warranty is in lieu of all other warranties, expressed or implied, including warranty of merchantability. The manufacturer assumes no responsibility whatsoever for consequential damages resulting from the use of it’s products. ® 3
- Page 1 and 2: Since 1956, Clark Seals, Ltd. ® ha
- Page 3: Table of Contents Applications 2 Pr
- Page 7 and 8: Material Selection Elastomer Select
- Page 9 and 10: Seal Designs CPZ pg. 38 VA2Y pg. 18
- Page 11 and 12: for two row Timken ® TNASW & TNASW
- Page 13 and 14: Note: Tables are arranged by cone b
- Page 15 and 16: Note: Tables are arranged by cone b
- Page 17 and 18: Note: Tables are arranged by cone b
- Page 19 and 20: E Note: Tables are arranged by cone
- Page 21 and 22: Note: Tables are arranged by cone b
- Page 23 and 24: Bearing Nomenclature Cup Width Cage
- Page 25 and 26: Seal Selection By Cone Number ® Ti
- Page 27 and 28: Seal Selection By Cone Number ® Ti
- Page 29 and 30: Seal Selection Timken Bearing Numbe
- Page 31 and 32: Seal Selection By Cone Bore Timken
- Page 33 and 34: Seal Selection Cone " Cup " Timken
- Page 35 and 36: D d BEARING ® for Radial Ball, Sph
- Page 37 and 38: D d BEARING ® for Radial Ball, Sph
- Page 39 and 40: D d BEARING ® for Radial Ball, Sph
- Page 41 and 42: Note: Tables are arranged by retain
Material Selection<br />
Polymer Mechanical Properties <strong>and</strong> Compatibility<br />
Base Polymer<br />
Nitrile Neoprene<br />
Material Code<br />
Mechanical Properties<br />
Temperature Range<br />
4<br />
Abrasion Resistance<br />
Compression Set<br />
Tear Resistance<br />
Resistance To:<br />
Cold<br />
Heat<br />
Oxidation<br />
Ozone<br />
Sunlight Aging<br />
Water<br />
Compatibility with Lubricants:<br />
Automatic Transmission Fluid<br />
E.P. Lubricants<br />
Grease<br />
Hydraulic Fluid<br />
Petroleum Base Lubricating Oils<br />
Engine Oil SAE 30 wt.<br />
SAE 10 wt.<br />
Gear Oil Super Gear<br />
Hypoid Gear<br />
Compatibility with Solvents:<br />
Aliphatic Hydrocarbons<br />
Aromatic Hydrocarbons<br />
Halogenated Solvents<br />
Ketones<br />
Compatibility with Acids:<br />
20% Hydrochloric Acid Solution<br />
30% Sulfuric Acid Solution<br />
Compatibility with Other Fluids:<br />
Alcohol<br />
Alkali<br />
Animal <strong>and</strong> Vegetable Oils<br />
Gasoline<br />
Water-Glycol<br />
Durometer Range:<br />
®<br />
-<br />
-50°F to 250°F<br />
-45°C to 120°C<br />
G<br />
G<br />
F<br />
G<br />
G<br />
F<br />
G<br />
P<br />
G<br />
E<br />
G<br />
E<br />
E<br />
E<br />
E<br />
E<br />
E<br />
G<br />
G<br />
F<br />
P<br />
P<br />
F<br />
F<br />
E<br />
G<br />
E<br />
F<br />
E<br />
65-90<br />
N<br />
-40°F to 225°F<br />
-40°C to 105°C<br />
E<br />
F<br />
G<br />
F<br />
G<br />
E<br />
E<br />
E<br />
F<br />
G<br />
G<br />
E<br />
E<br />
G<br />
G<br />
G<br />
G<br />
G<br />
G<br />
F<br />
P<br />
P<br />
F<br />
E<br />
E<br />
G<br />
G<br />
F<br />
F<br />
65-85<br />
Polyacrylate<br />
P<br />
-20°F to 300°F<br />
-30°C to 150°C<br />
F<br />
F<br />
F<br />
F<br />
E<br />
E<br />
E<br />
G<br />
F<br />
E<br />
E<br />
E<br />
E<br />
E<br />
E<br />
E<br />
E<br />
G<br />
P<br />
P<br />
P<br />
P<br />
F<br />
F<br />
P<br />
P<br />
E<br />
P<br />
P<br />
65-85<br />
Silicone<br />
S<br />
-80°F to 400°F<br />
-60°C to 200°C<br />
P<br />
G<br />
P<br />
E<br />
E<br />
G<br />
E<br />
G<br />
G<br />
F<br />
P<br />
E<br />
P<br />
F<br />
E<br />
G<br />
F<br />
P<br />
P<br />
P<br />
P<br />
P<br />
F<br />
P<br />
G<br />
P<br />
G<br />
P<br />
G<br />
65-80<br />
Florocarbon<br />
(Viton ® )<br />
V<br />
-30°F to 400°F<br />
-35°C to 200°C<br />
G<br />
E<br />
F<br />
F<br />
E<br />
E<br />
E<br />
E<br />
G<br />
E<br />
E<br />
E<br />
E<br />
E<br />
E<br />
E<br />
E<br />
E<br />
E<br />
E<br />
G<br />
P<br />
E<br />
E<br />
F<br />
F<br />
E<br />
E<br />
G<br />
65-90<br />
E - Excellent.<br />
G - Good for most applications.<br />
F - Fair, not recommended.<br />
P - Poor, do not use.