491 Locks - Häfele
491 Locks - Häfele 491 Locks - Häfele
Dimensional data not binding. We reserve the right to alter specifications without notice. Central Locking Rail Mount Lock Cylinder Module System Häfele provides a complete system for central locking of desks and credenzas, with one lock mounted in a minimum 25 mm front exposed rail. L Lockbar F Actuator N Shaft Clip M or MM Flexible Shaft C D or E Cylinder Body 5 22 17.5 10.5 18 23 38 44 32 12.5 16.5 90.6 45 F ø12.5 Actuator 30 43 • See page 529 for locking accessories J J 4.5 30 Additional locking pins are required. Adjustable Drawer Locking Pin 7.5 8 14 Call 1-800-423-3531 from anywhere in Canada - www.hafele.com Locks C Central Locking System Body - Centre Drawer Application With centre drawer bolt, accommodates flexible shaft M or MM Material: Lock case: nylon Cylinder housing: zinc die-cast Colour Cat. No. black/unfinished 237.46.054 Packing: 10 pcs. D Central Locking System Body - without Centre Drawer Accommodates flexible shaft M or MM Material: Lock case: nylon Cylinder housing: zinc die-cast Colour Cat. No. black/unfinished 237.46.003 Packing: 10 pcs. E Desk Central Locking System Body - Double Door Application With centre bolt to lock 2 doors Accommodates flexible shaft M or MM Material: Lock case: nylon Cylinder housing: zinc die-cast Colour Cat. No. black/unfinished 237.46.053 Packing: 10 pcs. F Lockbar Actuator Transmits horizontal rotation of flexible shaft M or MM to vertical movement of lockbar L . Material: steel Spindle guide: plastic Colour Cat. No. galvanized/black 234.87.023 Packing: 10 pcs. Note: An additional locking pin J is required to transfer movement - see drawing above. • See page 513 for snap-in lock cores Insert, push until they snap together Insert, push until they snap togehter Credenza With Double Doors For Accessories: L Lockbar J Locking Pins Q Drawer Wedges K Bar Retaining Brackets Miscellaneous Strikes, see page 529 Dimensions in mm Inches are approximate 522
Central Locking Anti-Tip System Cylinder Module System • Meets or exceeds ANSI/BIFMA requirements • Only one drawer can be opened at a time • For up to 4 drawers maximum Dimensions in mm Inches are approximate 523 A B A B Marking Step 1 S B B A A Installation of arresting pins Stop bracket Locks When any drawer is pulled open, the wedges on that drawer move the lockbar into a locked position, preventing any further drawers from being opened • Installation of wedges A and B, must be installed as shown in drawing at left • When wedges are installed in the proper positions as shown, only one drawer will ever be open at any one time, even if two drawers are pulled at exactly the same time! Step 2 Call 1-800-423-3531 from anywhere in Canada - www.hafele.com Dimensional data not binding. We reserve the right to alter specifications without notice.
- Page 1 and 2: 491 Locks Locking Systems - Overvie
- Page 3 and 4: Locking Systems - Overview Häfele
- Page 5 and 6: Decorative Keys Lever Bit The desir
- Page 7 and 8: SYMO 3000 Locking System Informatio
- Page 9 and 10: SYMO 3000 Dead Bolt Rim Lock Backse
- Page 11 and 12: SYMO 3000 Dead Bolt Rim Lock With e
- Page 13 and 14: SYMO 3000 Inlaid lock, screw-mount
- Page 15 and 16: SYMO 3000 Locking cam, straight Loc
- Page 17 and 18: SYMO 3000 Counterpiece, for glass d
- Page 19 and 20: SYMO 3000 Central locking cylinder
- Page 21 and 22: SYMO 3000 Master key for plate-cyli
- Page 23 and 24: Dimensional data not binding. We re
- Page 25 and 26: Dimensional data not binding. We re
- Page 27 and 28: Dimensional data not binding. We re
- Page 29 and 30: Dimensional data not binding. We re
- Page 31 and 32: Dimensional data not binding. We re
- Page 33: Central Locking Single Pedestal Sid
- Page 37 and 38: Anti-Tip Interlock System No Lock D
- Page 39 and 40: Cylinder Module System Accessories
- Page 41 and 42: Accessories Cylinder Module System
- Page 43 and 44: Deadbolt Locks FH Series Deadbolt L
- Page 45 and 46: Tambour and Sliding Door Locks FH S
- Page 47 and 48: Central Locking System FH Series Si
- Page 49 and 50: Cam Locks H Series Cam Lock, with c
- Page 51 and 52: Central Locking System H Series Cen
- Page 53 and 54: Cam Locks 1 1/8" 1/8" Dimensions in
- Page 55 and 56: Cam Locks • Easily converted from
- Page 57 and 58: Cam Locks • Economical drawer loc
- Page 59 and 60: Central Locking System Accessories
- Page 61 and 62: Sliding Door Locks Dimensions in mm
- Page 63 and 64: Sliding Door Locks Glass Door Cylin
- Page 65 and 66: Dimensional data not binding. We re
- Page 67 and 68: Dimensional data not binding. We re
- Page 69 and 70: Dimensional data not binding. We re
- Page 71 and 72: Dimensional data not binding. We re
- Page 73 and 74: Dimensional data not binding. We re
- Page 75 and 76: Dimensional data not binding. We re
- Page 77 and 78: Dimensional data not binding. We re
- Page 79 and 80: Dimensional data not binding. We re
- Page 81 and 82: Dimensional data not binding. We re
- Page 83 and 84: Dimensional data not binding. We re
Central Locking Anti-Tip System<br />
Cylinder Module System<br />
• Meets or exceeds ANSI/BIFMA requirements<br />
• Only one drawer can be opened at a time<br />
• For up to 4 drawers maximum<br />
Dimensions in mm<br />
Inches are approximate<br />
523<br />
A<br />
B<br />
A<br />
B<br />
Marking<br />
Step<br />
1<br />
S<br />
B<br />
B<br />
A<br />
A<br />
Installation<br />
of arresting<br />
pins<br />
Stop bracket<br />
<strong>Locks</strong><br />
When any drawer is pulled open,<br />
the wedges on that drawer move<br />
the lockbar into a locked position,<br />
preventing any further drawers from<br />
being opened<br />
• Installation of wedges A and B, must be<br />
installed as shown in drawing at left<br />
• When wedges are installed in the proper<br />
positions as shown, only one drawer will ever<br />
be open at any one time, even if two drawers<br />
are pulled at exactly the same time!<br />
Step<br />
2<br />
Call 1-800-423-3531 from anywhere in Canada - www.hafele.com<br />
Dimensional data not binding. We reserve the right to alter specifications without notice.