Applicafion Guide - Quality Chain Canada

Recommendations

Info

GROUSER BAR - Suggested Size Selecton CATERPILLAR TRACTOR MODEL SUG. SIZE TRACTOR MODEL SUG. SIZE D2, D3, D4, 931, 933, 941, 955 D6C, D7, 571A, 572, 977 L L, K, A, E D5, D6, 561, 951, 955K, 955L, 977 A, E D8L, D9, D9G, D9H T, H, S, J, M D8H, K, N, R 583, 983 C, G, H D10L, D11 R D9L, D9N, D10N S, M INTERNATIONAL TRACTOR MODEL SUG. SIZE TRACTOR MODEL SUG. SIZE TD6, 7, 8, 9, 100, 125, 150 L OVA OV OVAA OV OVAA PAGE 112 TD14, TD15, TD18, TD20, 175, 250 L, K, A, E TD24, TD25, TD30, TD40 T,C,G,H,S,J,M CASE TRACTOR MODEL SUG. SIZE TRACTOR MODEL SUG. SIZE 310, 350, 420DB, 450, 520 L 600,750,800,850,1000,1150,1550 K, A, E JOHN DEERE TRACTOR MODEL SUG. SIZE TRACTOR MODEL SUG. SIZE 350,350B,420,430,440,1010,2010 L 450, 450B, 555, 850 KOMATSU K,A, E TRACTOR MODEL SUG. SIZE TRACTOR MODEL SUG. SIZE D41, D20, D53, D55, D58, D63 L, A D60, D65, D68, D75, D80, D83, D85 K, E D135, D155, D155AX G, H, S, T D275, D355, D375A-1 J, M, P D375A-2 M D475A-2 R TRACTOR MODEL TEREX SUG. SIZE TRACTOR MODEL SUG. SIZE C6, 8230, 8240 L, K, A, E TC12, 8280 C, G, H 8250 T, H, S, J, M ALLIS-CHALMERS TRACTOR MODEL SUG. SIZE TRACTOR MODEL SUG. SIZE HD3, HD4, HD6, HD7G L, A, E HD9, HD11, HD11B, HD11EP A, E HD15, HD16 HD16B, HD16DP K,E HD41, HD41B T, S, M, R HD19, HD20, HD21, HD21B QUESTIONS??? Call us TOLL FREE @ 1-888-507-9734 ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE E, K, T, C, G, H, S, L
STANDARD ICE LUGS TO 3/4’’ SCALE 3’’ 4’’ Available from stock in 3’’ & 4’’ Lengths in: TYPE L (BROWN) TYPE K (ORANGE) TYPE E (DARK BLUE) TYPE C (GREY) Other Lengths and Types available upon request ICE LUGGING - Suggested Procedure CONSIDERATIONS BEFORE STARTING 1) Choose a pattern for placing lugs on pads, that gives the maximum grip with the minimum number of lugs. 2) Select a size of lug that gives the minimum amount of distance from the pad face to the top of the lug and still grips adequately. Choose as long of a lug as possible. C) There must be no arc strikes on the fnished pad as this may cause breaking in the pad. If they do occur, thoroughly grind the area to remove the arc damage. D) The principle of high heat input and slow cooling will provide optimum weld performance. REQUIRMENTS 1) Clean dry pads - hand warm if possible. (if re-grousered best to apply lugs as re-grouser and pads are still hot). B) 3/16’’ E7018 electrodes either from fresh container or holding ovens @ 250 Degrees F. (Keep electrodes hot). C) Ice lug to be welded on pad in horizontal position. PROCEDURE 1) Select 3/32’’ or 1/8’’ electrode size for the job B) Place lug on grouser in such position that the ends of the ice lug do not line up with rail excess in back of the pad. C)To position ice lug on the grouser, place tacks in the middle of the lug at 1/2’’ in from each end of the lug with a gap of 1/8’’ lef afer tacking. (Tacks must cover their own arc strikes). Clean slag from tacks. D) To start fill pass, strike arc on the tack closest to the outside edge of pad. Then move the bead out of the edge of the ice lug only, without breaking the arc, allow time for weld deposit to completely fill groove then return over bead and tack to the other edge of the ice lug, again allowing time for crater to fill in, then return bead back 1’’. (Make sure no craters are lef on ends of welds.) Complete weld with one stop and start if possible. E) Allow to cool slowly , do not allow weld to be quenched with water or snow. The method described above is a practical solution to help reduce the breakage problems encountered in ice lugging. It is not a guaranteed procedure. To fully ensure successful ice lugging, preheating of the grouser bar to 200 Degrees F. is necessary. QUESTIONS??? Call us TOLL FREE @ 1-888-507-9734 ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE PAGE 113 OVA OV OVAA OV OVAA
Page 1 and 2:
OVA OV OVAA OV OVAA by #1 - 2133 19
Page 3 and 4:
TABLE OF CONTENTS HELPFUL INFORMATI
Page 5 and 6:
ESSENTIAL INFORMATION For Ordering
Page 7 and 8:
1 2 3 4 5 6 7 8 9 10 11 12 Below is
Page 9 and 10:
CASE NEW HOLLAND / FORD KOBELCO LIN
Page 11 and 12:
Most Penetratve Least Penetratve BU
Page 13 and 14:
TEETH & ADAPTERS Families by Brand
Page 15 and 16:
J200 Series Adapters TYPE PICTURE P
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
J450 / J460 Series Adapters TYPE PI
Page 29 and 30:
Page 31 and 32:
POCKET DIMENSIONS (WxHxD): 2-3/8’
Page 33 and 34:
CAT STYLE RIPPER FAMILY: R350 Serie
Page 35 and 36:
CAT STYLE RIPPER FAMILY: R500 Serie
Page 37 and 38:
ESCO STYLE CONICAL FAMILIES ESCO ST
Page 39 and 40:
ESCO STYLE CONICAL FAMILY: C30 Seri
Page 41 and 42:
ESCO STYLE CONICAL FAMILY: C40 Seri
Page 43 and 44:
ESCO STYLE HELILOCK FAMILY: H21 Ser
Page 45 and 46:
ESCO STYLE SUPER-V FAMILY: V13 Seri
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
KOMATSU STYLE FAMILY: PC60 Series P
Page 53 and 54:
KOMATSU STYLE FAMILY: PC400 Series
Page 55 and 56:
KOMATSU STYLE RIPPER FAMILY: D275 S
Page 57 and 58:
KOMATSU STYLE RIPPER FAMILY: D475 S
Page 59 and 60:
H&L STYLE FAMILY: 2A Series Profile
Page 61 and 62: H&L STYLE: 23 Series Adapters TYPE
Page 63 and 64: H&L STYLE FAMILY:25 Series Profiles
Page 65 and 66: H&L STYLE RIPPER FAMILY: 36C Series
Page 67 and 68: HENSLEY STYLE PARABOLIC FAMILY: X15
Page 71 and 72: HENSLEY STYLE PARABOLIC FAMILY:X330
Page 77 and 78: HYUNDAI STYLE FAMILY: E161 Series P
Page 79 and 80: CUTTING EDGES OVA OV OVAA OV OVAA
Page 81 and 82: SCRAPER OEM fit or custom designed
Page 83 and 84: CUTTING EDGE PROFILES DOUBLE BEVEL
Page 85 and 86: CAT MACHINE MODEL 416, 426, 428, 43
Page 87 and 88: CAT MACHINE MODEL BUCKET STYLE 977
Page 89 and 90: CAT MACHINE MODEL 112, 12, 12G, 120
Page 91 and 92: CAT MACHINE MODEL BLADE STYLE CENTE
Page 93 and 94: CAT MACHINE MODEL CATERPILLAR RIPPE
Page 95 and 96: MOLDBOARD LENGTH 10 FOOT 11 FOOT 12
Page 97 and 98: KOMATSU MACHINE MODEL BUCKET STYLE
Page 99 and 100: KOMATSU MACHINE MODEL D50A, D53A D5
Page 101 and 102: KOMATSU MACHINE MODEL D85A, D85E U-
Page 103 and 104: KOMATSU MACHINE MODEL GD300A-1 2001
Page 105 and 106: MACHINE WEIGHT Up to 60,000 LBS 70,
Page 107 and 108: GRADE 8 PLOW BOLTS - NUTS - WASHER
Page 109 and 110: GROUSER BARS & ICE LUGS SCARIFIER G
Page 111: TRACTOR PAD WIDTH GROUSER BAR - Qua
Page 115 and 116: CONICAL BIT PROFILES C87WFRKCSB (20
show all

Applicafion Guide - Quality Chain Canada

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?