Applicafion Guide - Quality Chain Canada

Recommendations

Info

OVA OV OVAA OV OVAA GROUSER RETREAD BAR STANDARD Grouser Bar HEAT TREATED Grouser Bar PAGE 110 - All sizes available in 10f standard lengths - High <strong>Quality</strong> Work-Hardening Steel - All sizes available in 10f standard lengths - - Carbon-Boron Steel facilitates weld ability - - Heat Treated to Rockwell Hardness of 42-44 - - Optimum Wear performance & durability for extreme working conditions - QUESTIONS??? Call us TOLL FREE @ 1-888-507-9734 ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
TRACTOR PAD WIDTH GROUSER BAR - Quantty Chart Chart figures indicate the MINIMUM Number of 10 Foot LENGTHS of Grouser Retread Bar required. NUMBER OF PADS PER TRACTOR 66 68 70 72 74 76 78 80 82 84 90 92 94 36’’ 22 23 24 24 25 26 26 27 28 28 30 31 32 30’’ 17 17 18 18 19 19 20 20 21 21 23 23 24 28’’ 17 17 18 18 19 19 20 20 21 21 23 23 24 27’’ 17 17 18 18 19 19 20 20 21 21 23 23 24 26’’ 17 17 18 18 19 19 20 20 21 21 23 23 24 24’’ 14 14 14 15 15 16 16 16 17 17 18 19 19 22’’ 14 14 14 15 15 16 16 16 17 17 18 19 19 20’’ 11 12 12 13 13 13 14 14 14 14 15 16 16 18’’ 11 12 12 13 13 13 14 14 14 14 15 16 16 GROUSER BAR - Welding Procedure 1A) Pads and bars must be clean and free from moisture at all times. 1B) Rods must be used immediately when taken from moisture-protecting package. 2A) Dress old Grouser back to one inch with oxy-acetlylene cutting process - resulting in a straight, smooth edge. Clean cut surface of oxide & slag. Cut Grouser 1” shorter than pad. 2B) On bars with weld preparation ends of 1/4’’, fit bar with 3/32’’ root gap 1/2’’ from ends of pads. On bars with weld preparation ends of 5/16’’ - 3/8’’, fit bar with 1/8’’ root gap 1/2’’ from ends of pads. 3A) Tack bar on pad at both ends and center (one side only) with E7016-E7018 electrode using medium to high side of recommended amerage settings. Tacks must be minimum of 2” long and flat surface to assist in cleaning. Apply tacks with a large deposit using high heat and a slow rate of travel. 4A) The backstep welding technique should be utilized using a slow rate of travel, large electrodes and high heat. The first pass should be on the opposite of the tacks. Start in the middle of the bar and weld out to the end. Starting at the opposite end, weld to the start of the first deposit. Repeat this procedure for the tacked side of the bar. (on the larger bars this procedure may have to be done twice.) Always clean start of first pass before joining wiht the second pass. If a multi-layer deposit is required, do not clean slag off lower layer until immediately before next deposit. Root passes must be flat on face and fairly heavy. Finish pass contour should be slightly convex. No undercut is allowed on tacks or passes. All craters at the ends of welds should be filled. 4B) Bar ends should be cleaned and corked with fillet weld using E7018 Rod. 5A) Avoid quenching or rapid cooling of welds (ie. Water, mud, snow, etc). NOTE: To completely ensure a proper welding procedure... PREHEAT PADS TO 500 Deg PRIOR TO WELDING! QUESTIONS??? Call us TOLL FREE @ 1-888-507-9734 ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE PAGE 111 OVA OV OVAA OV OVAA
Page 1 and 2:
OVA OV OVAA OV OVAA by #1 - 2133 19
Page 3 and 4:
TABLE OF CONTENTS HELPFUL INFORMATI
Page 5 and 6:
ESSENTIAL INFORMATION For Ordering
Page 7 and 8:
1 2 3 4 5 6 7 8 9 10 11 12 Below is
Page 9 and 10:
CASE NEW HOLLAND / FORD KOBELCO LIN
Page 11 and 12:
Most Penetratve Least Penetratve BU
Page 13 and 14:
TEETH & ADAPTERS Families by Brand
Page 15 and 16:
J200 Series Adapters TYPE PICTURE P
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
J450 / J460 Series Adapters TYPE PI
Page 29 and 30:
Page 31 and 32:
POCKET DIMENSIONS (WxHxD): 2-3/8’
Page 33 and 34:
CAT STYLE RIPPER FAMILY: R350 Serie
Page 35 and 36:
CAT STYLE RIPPER FAMILY: R500 Serie
Page 37 and 38:
ESCO STYLE CONICAL FAMILIES ESCO ST
Page 39 and 40:
ESCO STYLE CONICAL FAMILY: C30 Seri
Page 41 and 42:
ESCO STYLE CONICAL FAMILY: C40 Seri
Page 43 and 44:
ESCO STYLE HELILOCK FAMILY: H21 Ser
Page 45 and 46:
ESCO STYLE SUPER-V FAMILY: V13 Seri
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
KOMATSU STYLE FAMILY: PC60 Series P
Page 53 and 54:
KOMATSU STYLE FAMILY: PC400 Series
Page 55 and 56:
KOMATSU STYLE RIPPER FAMILY: D275 S
Page 57 and 58:
KOMATSU STYLE RIPPER FAMILY: D475 S
Page 59 and 60: H&L STYLE FAMILY: 2A Series Profile
Page 61 and 62: H&L STYLE: 23 Series Adapters TYPE
Page 63 and 64: H&L STYLE FAMILY:25 Series Profiles
Page 65 and 66: H&L STYLE RIPPER FAMILY: 36C Series
Page 67 and 68: HENSLEY STYLE PARABOLIC FAMILY: X15
Page 71 and 72: HENSLEY STYLE PARABOLIC FAMILY:X330
Page 77 and 78: HYUNDAI STYLE FAMILY: E161 Series P
Page 79 and 80: CUTTING EDGES OVA OV OVAA OV OVAA
Page 81 and 82: SCRAPER OEM fit or custom designed
Page 83 and 84: CUTTING EDGE PROFILES DOUBLE BEVEL
Page 85 and 86: CAT MACHINE MODEL 416, 426, 428, 43
Page 87 and 88: CAT MACHINE MODEL BUCKET STYLE 977
Page 89 and 90: CAT MACHINE MODEL 112, 12, 12G, 120
Page 91 and 92: CAT MACHINE MODEL BLADE STYLE CENTE
Page 93 and 94: CAT MACHINE MODEL CATERPILLAR RIPPE
Page 95 and 96: MOLDBOARD LENGTH 10 FOOT 11 FOOT 12
Page 97 and 98: KOMATSU MACHINE MODEL BUCKET STYLE
Page 99 and 100: KOMATSU MACHINE MODEL D50A, D53A D5
Page 101 and 102: KOMATSU MACHINE MODEL D85A, D85E U-
Page 103 and 104: KOMATSU MACHINE MODEL GD300A-1 2001
Page 105 and 106: MACHINE WEIGHT Up to 60,000 LBS 70,
Page 107 and 108: GRADE 8 PLOW BOLTS - NUTS - WASHER
Page 109: GROUSER BARS & ICE LUGS SCARIFIER G
Page 113 and 114: STANDARD ICE LUGS TO 3/4’’ SCAL
Page 115 and 116: CONICAL BIT PROFILES C87WFRKCSB (20
show all

Applicafion Guide - Quality Chain Canada

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?