Operator's Manual - Smiths Medical

More documents

Recommendations

Info

S E C T I O N 1 2 • S p e c i f i c a t i o n s Mode of Operation Continuous Type of Current Alternating Ingress Protection Rating Performance IPX1 Relative Average Noise Level at 1000 Hz (front and back) 44.1 dBA Hose End Temperature Control Servo-controlled by thermistors placed at hose end The Snuggle Warm ® Electrical Type convective warming Average Maximum blankets meet the average and maximum contact surface temperature specified in ASTM F2196.02 46°C 48°C Approximate time to change the average contact surface temperature from 20°C to 36°C 7 minutes Electromagnetic Environmental Recommendations Recommended separation distances between portable and mobile RF communications equipment and the EQUATOR ® Convective Warmer The convective warmer is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the convective warmer can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the convective warmer as recommended below, according to the maximum output power of the communications equipment. Rated maximum Separation distance according to frequency of transmitter m output power of 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz transmitter d=[3.5/V1]P d=[3.5/E1]P d=[7/E1]P W 0.01 0.116 0.116 0.233 0.1 0.368 0.368 0.737 1 1.16 1.16 2.33 10 3.69 3.69 7.38 100 11.66 11.66 23.33 For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. 34 EQUATOR ® Convective Warmer | Operator’s <strong>Manual</strong>
SECTION 13 Symbols Symbols Definitions S Power ON Button. Power OFF Button. Ambient Temperature Setting Button 36°C Temperature Setting Button 40°C Temperature Setting Button 44°C Temperature Setting Button Over Temperature Alarm Indicator Under Temperature Alarm Indicator Disconnect Indicator Hose End Temperature Elapsed Time Display (h = hours) Type BF Equipment Protected Against Dripping Water S E C T I O N 1 3 • S y m b o l s EQUATOR ® Convective Warmer | Operator’s <strong>Manual</strong> 35
Page 1 and 2: EQUATOR ® Convective Warmer < EQ-5
Page 3 and 4: Contents 1. About this Manual 1 Ind
Page 5 and 6: SECTION 1 About this Manual S E C T
Page 7 and 8: Rear View 1 Thermistor Receptacle -
Page 9 and 10: SECTION 3 Important Safety Informat
Page 11 and 12: S E C T I O N 3 • I m p o r t a n
Page 13 and 14: SECTION 4 Assembly Instructions S E
Page 15 and 16: S E C T I O N 4 • A s s e m b l y
Page 17 and 18: Controls, Indicators, and Displays
Page 19 and 20: Step 2: Determine the Convective Wa
Page 21 and 22: Attaching the Older Style Sheet Cli
Page 23 and 24: 3 Verify that the self-test complet
Page 25 and 26: Problem Possible Cause/Solution Und
Page 27 and 28: 7 After thoroughly cleaning the con
Page 29 and 30: S E C T I O N 8 • M a i n t e n a
Page 31 and 32: S E C T I O N 8 • M a i n t e n a
Page 33 and 34: SECTION 10 Limited Warranty S E C T
Page 35 and 36: SECTION 11 Service S E C T I O N 1
Page 37: SECTION 12 Specifications System Sp
Page 41 and 42: Symbols Definitions 6 CLASS 1 ; : C
Page 43 and 44: Convective Warming Blanket A P P E
Page 45 and 46: Convective Warming Blanket A P P E
Page 47 and 48: APPENDIX B A P P E N D I X B • P
Page 49 and 50: A P P E N D I X B • P o s i t i o
Page 67 and 68: I n d e x Numerics 36°C Temperatur
Page 69: I n d e x Thermistor receptacle 3 T

Operator's Manual - Smiths Medical

Create successful ePaper yourself

Delete template?

Save as template?