6700 Portable Sampler User Manual - Isco

More documents

Recommendations

Info

Figure 19 Opening the Controller EMI Shield Desiccant Box Figure 20 Main Circuit Board Connections Battery Keypad Connector 6700 SAMPLERS Connector Board Connector 78 Distributor Connectors Module Connector Liquid Detector Connector Pump Count Connector
CAUTION Desiccant may produce irritating fumes when heated. Observe the following precautions: Useaventedoveninawell ventilated room. Do not remain in the room while recharging is taking place. Use the recommended temperature. There have been reports of irritating fumes coming from the desiccant during reactivation. While our attempts to duplicate the problem have been unsuccessful, we still urge you to use caution. Material Safety Data Sheets are provided in Appendix B. Battery Warning WARNING! REPLACE INTERNAL BATTERY BEFORE 17-OCT-97 Note Isco recommends you replace the battery every five years, as soon as the battery warning appears. To insure that the replacement meets Isco’s specifications, use only Isco replacement batteries. (See Appendix D, Replacement Parts.) 6700 SAMPLERS RECHARGING THE DESICCANT The 6700 Samplers use a desiccant bag inside the controller case to prevent moisture damage to its electronic components. Follow the instructions in Opening the Controller Case on page 77 to open the controller. Remove the bag from the cardboard box atthefrontofthecase(Figure 19). How To Recharge The Desiccant Do not put the cardboard box in the oven. You should recharge the desiccant when the area marked “30” on the paper humidity indicator turns pink. Place a sheet of brown paper on a flat metal sheet. You can use a brown grocery bag and a typical cookie sheet. Place only the bags on the sheet. Do not stack the bags on top of each other or allow them to touch. Place in a vented, circulating forced air, convection oven in a well ventilated room. Allow two inches of air space between the top of the bags and the next metal tray above the bags. Keep the tray a minimum of 16 inches from heating element. Heat the bags at a temperature of 240 to 250oF(116to 121oC) for 12 to 16 hours. At the end of the time period, the bags should be immediately removed and placed in an air tight container for cooling. The desiccant will be recharged to approximately 80 to 90% of its previous capacity. After repeated recharging, the desiccant bag may require replacement. Some bags will have the temperature and time for recharging the desiccant printed on the bag. If they differ, use the temperature and time printed on the bag. REPLACING THE INTERNAL BATTERY A lithium battery housed inside the controller maintains power to the sampler’s memory when the controller is disconnected from a power source. If it discharges completely, the sampler will lose all program settings and all data stored in memory when the external power source is disconnected. The battery requires replacement every five years. The sampler displays a warning withinonemonthofitsexpectedlifetoalertyoutothebattery’s impending expiration. The warning appears each time you turn the sampler on until you reset the alarm. When you reset the alarm, the sampler resets the warning to a date 59 months from the current date. While replacing the battery, it is likely that the stored readings will be lost and your program will revert to the default program. Before proceeding, retrieve the stored data (see Collecting Reports on page 59) and record your program settings. To replace the internal battery: 1. Open the controller case (see Opening the Controller Case on page 77). Separate the case bottom and top by removing the two distributor connectors (Figure 19). 2. Lift the desiccant box from the case (Figure 19). 79
Page 1:
INSTRUCTION MANUAL 6700 Portable Sa
Page 5 and 6:
Table of Contents Chapter1.Introduc
Page 7 and 8:
List of Figures 1. Menu Tree for St
Page 9 and 10:
6700 SAMPLERS Chapter 1 Introductio
Page 11 and 12:
6700 SAMPLERS Table 1: 6700 Standar
Page 13 and 14:
SAMPLE DELIVERY SYSTEM FEATURES 670
Page 15 and 16:
6700 SAMPLERS Table 2: 6700 Standar
Page 17 and 18:
6700 SAMPLERS Table 3: Technical Sp
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
6700 SAMPLERS Chapter 2 Programming
Page 25 and 26:
c d 6700 SAMPLERS To enter a number
Page 27 and 28:
Entering Times and Dates e ENTER TI
Page 29 and 30:
l m n Site Description or Program N
Page 31 and 32:
Using Help Notes Although this exam
Page 33 and 34:
Extended Programming Features Pacin
Page 35 and 36: Note: If the Bottle Full Detect set
Page 37 and 38: 6700 SAMPLERS Example 5 Standard Pr
Page 39 and 40: 6700 SAMPLERS Example 6 Storm Water
Page 47 and 48: Distributor Arm Figure 2 Installing
Page 49 and 50: 6700 SAMPLERS Figure 3 Placing the
Page 51 and 52: 6700 SAMPLERS Figure 6 Placing the
Page 53 and 54: Figure 9 Composite Bottles 6700 SAM
Page 55 and 56: 6700 SAMPLERS STRAINERS Isco offers
Page 57 and 58: WARNING If you must enter a manhole
Page 59 and 60: 6700 SAMPLERS Table 9 Connecting Is
Page 61 and 62: Figure 11 Running a Program PROGRAM
Page 63 and 64: l m n o Warning Messages WARNING: R
Page 65 and 66: 6700 SAMPLERS Adjust Volume Select
Page 67 and 68: 1 2 3 4 Interrogator 581 RTD Viewin
Page 69 and 70: 6700 SAMPLERS To start a report fro
Page 71 and 72: ERROR CODES (CONTINUED) 6700 SAMPLE
Page 73 and 74: Figure 13 Report: Sampling Results
Page 75 and 76: 6700 SAMPLERS Figure 14 Report: Com
Page 77 and 78: Figure 15 Report: Summary (continue
Page 79 and 80: 1 2 3 4 5 6 7 8 9 10 Calibrating Sa
Page 81 and 82: 5 6 7 8 9 10 11 12 13 14 15 Diagnos
Page 83 and 84: The pump’s safety lock prevents t
Page 85: 6700 SAMPLERS Example 7 Resetting t
Page 89 and 90: 6700 SAMPLERS Chapter 5 Reference C
Page 91 and 92: Extended Time Pacing Screens The sc
Page 93 and 94: 14 15 16 17 Time Switched Distribut
Page 95 and 96: Internal Sampler Enable Screens Fig
Page 97 and 98: Pause and Resume Screens Screen cha
Page 99 and 100: 6700 SAMPLERS Figure 22 Start Time
Page 101 and 102: Selecting Hardware Setup 41 42 43 4
Page 103 and 104: Turning on Master/Slave Sampling 47
Page 105 and 106: Figure 23 Event Mark Timing Diagram
Page 107 and 108: Note Connecting either the serial o
Page 109 and 110: 6700 SAMPLERS The software version
Page 111 and 112: Command Driven Mode Charts showing
Page 113 and 114: 6700 SAMPLERS 1 = WAITING TO SAMPLE
Page 115 and 116: 6700 SAMPLERS Chapter 6 Software Op
Page 117 and 118: Table 13 6700 Telephone Commands Co
Page 119 and 120: 6700 SAMPLERS A flow-through chambe
Page 121 and 122: 6700 SAMPLERS Figure 26 Standard Pr
Page 123 and 124: 6700 SAMPLERS Figure 28 Standard Pr
Page 125 and 126: Figure 30 View Report RUN PROGRAM V
Page 127 and 128: Figure 32 Manual Functions Screens
Page 129 and 130: 6700 SAMPLERS Figure 35 Extended Pr
Page 137 and 138:
6700 SAMPLERS Figure 43 Extended Pr
Page 139 and 140:
6700 SAMPLERS Figure 45 Extended Pr
Page 141 and 142:
6700 SAMPLERS Figure 47 Analog Outp
Page 143 and 144:
6700 SAMPLERS Appendix B Material S
Page 145 and 146:
6700 SAMPLERS 137
Page 147 and 148:
6700 SAMPLERS 139
Page 149 and 150:
6700 SAMPLERS 141
Page 151 and 152:
6700 SAMPLERS 143
Page 153 and 154:
6700 SAMPLERS 145
Page 155 and 156:
6700 SAMPLERS 147
Page 157 and 158:
6700 SAMPLERS 149
Page 159 and 160:
The persons stationed at the surfac
Page 161 and 162:
Table 16 Hazardous Gases Gas Chemic
Page 163 and 164:
6700 SAMPLERS Appendix D Replacemen
Page 165 and 166:
6700 SAMPLERS ITEM INVENTORY NO. DE
Page 167 and 168:
6700 SAMPLERS MODEL 6700 CONTROLLER
Page 169 and 170:
6700 SAMPLERS MODEL 6700 CONTROLLER
Page 171 and 172:
Isco, Inc. P.O. Box 82531 Lincoln,
Page 173 and 174:
6700 SAMPLERS Bulk Sets of Bottles
Page 175 and 176:
6700 SAMPLERS YSI 600 Sonde YSI 600
Page 177 and 178:
G Grab samples 56, 70 Graduated cyl
Page 179:
DECLARATION OF CONFORMITY Applicati
show all

6700 Portable Sampler User Manual - Isco

Create successful ePaper yourself

Delete template?

Save as template?