6700 Portable Sampler User Manual - Isco

More documents

Recommendations

Info

6700 SAMPLERS Chapter 3 Operation Chapter Contents Installation and Operation Checklist Preparing the Sampler Installing the Sampler Running Programs Servicing the Sampler Sampling Reports Grab Samples Calibrating INSTALLATION AND OPERATION CHECKLIST 1. Prepare the sampler. a. Adjust the distributor arm to fit the bottle kit. Then install the distributor arm and discharge tube. (See Installing the Distributor Arm and Discharge Tube on page 39.) ForComposite bottle kits, install the composite tube guide and thread the discharge tube through the guide. (See CompositeBottleKitson page 44.) b. Install the bottle kit. (See Installing Bottle Kits on page 41, or CompositeBottleKitsonpage44.) c. Install the power source. (See Installing a Power Source on page 46.) d. Check the pump tube. Replace it if necessary and reset the pump tube warning. (See Checklist For Replacing Pump Tube on page 75.) e. Attach the suction line to the pump tube. (See Suction Line on page 46.) f. Attach a strainer to the suction line if necessary. (See Strainers on page 47.) 2. Install the sampler at the monitoring site. a. Ice the tub, if desired. (See Icing the Samples on page 49.) b. Install the strainer or end of the suction line in the flow streamandroutethesuctionlinetothesampler.(SeeIntake Placement and Tips for Routing Suction Line on page 49.) c. Install a module, if desired. Refer to the module manual for instructions for installing the module. d. Place the sampler in position. (See Positioning a Sampler on page 49.) e. Connect any necessary external instruments to the sampler. (See Connecting External Instruments on page 50.) 3. Program the sampler. Programming guidelines are in Chapter 2, Programming and in the module manual. 4. Run the sampling program. (See Running Programs on page 52.) 5. Service the sampler. a. Recover the sampler. (See Recovering the Sampler on page 58.) b. Collect the sample bottles. (See Collecting Sample Bottles on page 58.) c. Replace the battery if required. d. Collect the sampling data. (See Sampling Reports on page 59.) e. Replace the sample bottles. f. Run the sampling program. 38
Distributor Arm Figure 2 Installing the Distributor Arm Step 1 The two-piece arm has four positions, marked on the underside with the letters A, B, C, andD. Adjust the arm to the correct position for the bottle kit. Table 6 shows you the correct position for each kit. Thread the discharge through the spring and arm so that the tube protrudes from the arm 1/16 to 1/8 inch. Step 2 Attach the arm to the distributor shaft. The arm and shaft are keyed so that you can align them correctly. Secure the arm to the shaft with the black plastic nut. Step 3 Slide the end of the discharge tube onto the bulkhead fitting. 6700 SAMPLERS PREPARING THE SAMPLER INSTALLING THE DISTRIBUTOR ARM AND DISCHARGE TUBE When sampling with multiple bottles, both the compact and standard 6700 Samplers use a distributor arm. It is adjustable so that you can position the discharge tube over the bottles of each kit. Each bottle kit also uses a discharge tube of a specific length. Table 6 liststhecorrectdischargetubelengthsforeachbottlekit. After installing the distributor arm and discharge tube, run the distributor to each bottle position to ensure proper installation. If using bulk tubing to cut your own tubes, cut the ends of the tube square, not at an angle, and cut the length accurately. The two-piece distributor arm has four positions, marked on the undersidewiththelettersA,B,C,andD.Adjustthearmtothe correct position for the bottle kit being used. Table 6 shows the correct position for each kit. Thread the discharge tube through the spring and arm so that the tube protrudes from the arm 1 /16 to 1 /8 inch. Attach the arm to the distributor shaft. Secure the arm with the black plastic nut. Slide the free end of the discharge tube onto the bulkhead fitting. 39
Page 1: INSTRUCTION MANUAL 6700 Portable Sa
Page 5 and 6: Table of Contents Chapter1.Introduc
Page 7 and 8: List of Figures 1. Menu Tree for St
Page 9 and 10: 6700 SAMPLERS Chapter 1 Introductio
Page 11 and 12: 6700 SAMPLERS Table 1: 6700 Standar
Page 13 and 14: SAMPLE DELIVERY SYSTEM FEATURES 670
Page 15 and 16: 6700 SAMPLERS Table 2: 6700 Standar
Page 17 and 18: 6700 SAMPLERS Table 3: Technical Sp
Page 23 and 24: 6700 SAMPLERS Chapter 2 Programming
Page 25 and 26: c d 6700 SAMPLERS To enter a number
Page 27 and 28: Entering Times and Dates e ENTER TI
Page 29 and 30: l m n Site Description or Program N
Page 31 and 32: Using Help Notes Although this exam
Page 33 and 34: Extended Programming Features Pacin
Page 35 and 36: Note: If the Bottle Full Detect set
Page 37 and 38: 6700 SAMPLERS Example 5 Standard Pr
Page 39 and 40: 6700 SAMPLERS Example 6 Storm Water
Page 45: 6700 SAMPLERS Example 6 Storm Water
Page 49 and 50: 6700 SAMPLERS Figure 3 Placing the
Page 51 and 52: 6700 SAMPLERS Figure 6 Placing the
Page 53 and 54: Figure 9 Composite Bottles 6700 SAM
Page 55 and 56: 6700 SAMPLERS STRAINERS Isco offers
Page 57 and 58: WARNING If you must enter a manhole
Page 59 and 60: 6700 SAMPLERS Table 9 Connecting Is
Page 61 and 62: Figure 11 Running a Program PROGRAM
Page 63 and 64: l m n o Warning Messages WARNING: R
Page 65 and 66: 6700 SAMPLERS Adjust Volume Select
Page 67 and 68: 1 2 3 4 Interrogator 581 RTD Viewin
Page 69 and 70: 6700 SAMPLERS To start a report fro
Page 71 and 72: ERROR CODES (CONTINUED) 6700 SAMPLE
Page 73 and 74: Figure 13 Report: Sampling Results
Page 75 and 76: 6700 SAMPLERS Figure 14 Report: Com
Page 77 and 78: Figure 15 Report: Summary (continue
Page 79 and 80: 1 2 3 4 5 6 7 8 9 10 Calibrating Sa
Page 81 and 82: 5 6 7 8 9 10 11 12 13 14 15 Diagnos
Page 83 and 84: The pump’s safety lock prevents t
Page 85 and 86: 6700 SAMPLERS Example 7 Resetting t
Page 87 and 88: CAUTION Desiccant may produce irrit
Page 89 and 90: 6700 SAMPLERS Chapter 5 Reference C
Page 91 and 92: Extended Time Pacing Screens The sc
Page 93 and 94: 14 15 16 17 Time Switched Distribut
Page 95 and 96: Internal Sampler Enable Screens Fig
Page 97 and 98:
Pause and Resume Screens Screen cha
Page 99 and 100:
6700 SAMPLERS Figure 22 Start Time
Page 101 and 102:
Selecting Hardware Setup 41 42 43 4
Page 103 and 104:
Turning on Master/Slave Sampling 47
Page 105 and 106:
Figure 23 Event Mark Timing Diagram
Page 107 and 108:
Note Connecting either the serial o
Page 109 and 110:
6700 SAMPLERS The software version
Page 111 and 112:
Command Driven Mode Charts showing
Page 113 and 114:
6700 SAMPLERS 1 = WAITING TO SAMPLE
Page 115 and 116:
6700 SAMPLERS Chapter 6 Software Op
Page 117 and 118:
Table 13 6700 Telephone Commands Co
Page 119 and 120:
6700 SAMPLERS A flow-through chambe
Page 121 and 122:
6700 SAMPLERS Figure 26 Standard Pr
Page 123 and 124:
6700 SAMPLERS Figure 28 Standard Pr
Page 125 and 126:
Figure 30 View Report RUN PROGRAM V
Page 127 and 128:
Figure 32 Manual Functions Screens
Page 129 and 130:
6700 SAMPLERS Figure 35 Extended Pr
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
6700 SAMPLERS Figure 47 Analog Outp
Page 143 and 144:
6700 SAMPLERS Appendix B Material S
Page 145 and 146:
6700 SAMPLERS 137
Page 147 and 148:
6700 SAMPLERS 139
Page 149 and 150:
6700 SAMPLERS 141
Page 151 and 152:
6700 SAMPLERS 143
Page 153 and 154:
6700 SAMPLERS 145
Page 155 and 156:
6700 SAMPLERS 147
Page 157 and 158:
6700 SAMPLERS 149
Page 159 and 160:
The persons stationed at the surfac
Page 161 and 162:
Table 16 Hazardous Gases Gas Chemic
Page 163 and 164:
6700 SAMPLERS Appendix D Replacemen
Page 165 and 166:
6700 SAMPLERS ITEM INVENTORY NO. DE
Page 167 and 168:
6700 SAMPLERS MODEL 6700 CONTROLLER
Page 169 and 170:
6700 SAMPLERS MODEL 6700 CONTROLLER
Page 171 and 172:
Isco, Inc. P.O. Box 82531 Lincoln,
Page 173 and 174:
6700 SAMPLERS Bulk Sets of Bottles
Page 175 and 176:
6700 SAMPLERS YSI 600 Sonde YSI 600
Page 177 and 178:
G Grab samples 56, 70 Graduated cyl
Page 179:
DECLARATION OF CONFORMITY Applicati
show all

6700 Portable Sampler User Manual - Isco

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?