6700 Portable Sampler User Manual - Isco

6700 SAMPLERS
Table 3: Technical Specifications for the 6700 Compact and Standard Samplers
6700 COMPACT PORTABLE SAMPLER: PHYSICAL SPECIFICATIONS
Dimensions: Height: 27.6 inches (70.1 cm) Diameter: 17.75 inches (45.1 cm)
Sampler Tub Configurations: 24 wedge polyethylene bottles, 500 ml
12 round polyethylene bottles, 500 ml
12 round glass bottles, 375 ml
1 round polyethylene bottle, 9.4 liters (2.5 gallon)
1 round glass bottle, 9.4 liters (2.5 gallon)
Dry Weight: 31 lbs (14 kg)
This includes the top cover, center section, tub, controller, pump tube, distributor arm, distributor arm nut, and
discharge tube for the 24 bottle configuration.
Dry Weight With: 24 plastic bottles, insert, hold down, no caps 35 lbs (16 kg)
12 plastic bottles, insert, expander ring, no caps 35 lbs (16 kg)
12 glass bottles, insert, expander ring, no caps 43 lbs (20 kg)
1 plastic bottle and composite tube guide, no cap, arm or nut 33 lbs (15 kg)
1 glass bottle and composite tube guide, no cap, arm or nut 37 lbs (17 kg)
Filled Bottle Weight: 24 plastic bottles 70 lbs (32 kg)
12 plastic bottles 62 lbs (28 kg)
12 glass bottles 66 lbs (30 kg)
1 plastic bottle 66 lbs (30 kg)
1glassbottle 73lbs (33kg)
This includes everything in the Dry Weight, Dry Weight With, and Ice Capacity specifications, and the bottles are
filled to the capacities listed in Sampler Tub Configurations. This weight does not include a power source.
Ice Capacity: 24 plastic bottles 8 lbs (3.6 kg)
12 plastic bottles 13 lbs (5.9 kg)
12 glass bottles 13 lbs (5.9 kg)
1 plastic bottle 12 lbs (5.4 kg)
1 glass bottle 15 lbs (6.8 kg)
3 /4" x 3 /4" x 1 /4" approximate ice cube size. Ice capacity may vary with the size of the cubes.
Cooling Capacity:
Configuration:
24 plastic bottles
12 plastic bottles
12 glass bottles
1plasticbottle
1glassbottle
Sample Size Cooling Water Last Sample Last Sample Temp
250 ml Sample 41°F (5°C) Sample 24 55°F (13°C)
250 ml Sample 34°F (1°C) Sample 12 41°F (5°C)
175 ml Sample 34°F (1°C) Sample 12 43°F (6°C)
12–400 ml Samples 43°F (6°C) Composite Sample 43°F (6°C)
12–400 ml Samples 39°F (4°C) Composite Sample 39°F (4°C)
The cooling capacity is the temperature of the sample and the cooling water 24 hour after the last sample is
taken. The amount of ice specified for the ice capacity was used. The temperature of the sample liquid is 65°F
(18°C). The ambient temperature is 75°F (24°C).
Average Thermal
Resistance Factor:
R-11
The average R-value for a complete sampler. This includes a tub, center section, top cover, controller, pump tube,
distributor arm, and discharge tube.
General Notes:
1. All weights may vary ±1 lb (± 1 /2 kg).
2. All dimensions may vary ± 1 /4 inch (±0.64 cm).
3. Sample delivery specifications valid for the following conditions and ranges, unless otherwise stated: 75 o F
(24 o C) ambient, sample liquid–tap water at 50 to 80 o F(10to27 o C), sample volumes from 50 ml to 1000 ml,
suction line lengths of 25 ft (7.6 m) or less, suction heads from 1 to 20 ft (0.3 to 6.1 m), atmospheric pressure
between 29.92 and 31.89 inHg (760 and 810 mmHg), and a power source of an Isco High Capacity Power Pack
at 12.5 volts DC no load output.
13