AT+i Programmer's Manual - SE Spezial-Electronic AG
AT+i Programmer's Manual - SE Spezial-Electronic AG
AT+i Programmer's Manual - SE Spezial-Electronic AG
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>AT+i</strong> Result Code Summary<br />
85 RE<strong>SE</strong>RVED 86 Writing to internal non-volatile parameters<br />
database failed<br />
87 Web server IP registration<br />
failed<br />
88 Socket IP registration failed<br />
89 E-mail IP registration failed 90 IP registration failed for all methods specified<br />
91 RE<strong>SE</strong>RVED 92 RE<strong>SE</strong>RVED<br />
93 RE<strong>SE</strong>RVED 94 In Always Online mode, connection was lost<br />
and re-established<br />
96 A remote host, which had taken over iChip<br />
through the LATI port, was disconnected<br />
98 RE<strong>SE</strong>RVED<br />
99 RE<strong>SE</strong>RVED 100 Error restoring default parameters<br />
101 No ISP access numbers<br />
defined<br />
102 No USRN defined<br />
103 No PWD entered 104 No DNS defined<br />
105 POP3 server not defined 106 MBX (mailbox) not defined<br />
107 MPWD (mailbox password)<br />
not defined<br />
108 TOA (addressee) not defined<br />
109 REA (return e-mail address)<br />
not defined<br />
110 SMTP server not defined<br />
111 Serial data overflow 112 Illegal command when modem online<br />
113 E-mail firmware update<br />
attempted but not completed.<br />
The original firmware<br />
remained intact.<br />
114 E-mail parameters update rejected<br />
115 SerialNET could not be<br />
started due to missing<br />
parameters<br />
116 Error parsing a new trusted CA certificate<br />
117 RE<strong>SE</strong>RVED 118 Protocol specified in the USRV parameter<br />
does not exist or is unknown<br />
200 Socket does not exist<br />
201 Socket empty on receive 202 Socket not in use<br />
203 Socket down 204 No available sockets<br />
206 PPP open failed for socket<br />
207 Error creating socket 208 Socket send error<br />
209 Socket receive error 210 PPP down for socket<br />
212 Socket flush error<br />
215 No carrier error on socket<br />
operation<br />
216 General exception<br />
217 Out of memory 218 An STCP (Open Socket) command specified a<br />
local port number that is already in use<br />
219 SSL initialization/internal CA<br />
certificate loading error<br />
220 SSL3 negotiation error<br />
221 Illegal SSL socket handle.<br />
Must be an open and active<br />
TCP socket.<br />
222 Trusted CA certificate does not exist<br />
223 RE<strong>SE</strong>RVED 224 Decoding error on incoming SSL data<br />
225 No additional SSL sockets<br />
available<br />
226 Maximum SSL packet size (2K) exceeded<br />
227 <strong>AT+i</strong>SSND command failed 228 <strong>AT+i</strong>SSND command failed because checksum<br />
because size of stream sent<br />
calculated does not match checksum sent by<br />
exceeded 2048 bytes<br />
host<br />
300 HTTP server unknown<br />
301 HTTP server timeout 302 HTTP failure<br />
303 No URL specified 304 Illegal HTTP host name<br />
305 Illegal HTTP port number 306 Illegal URL address<br />
<strong>AT+i</strong> Programmer‘s <strong>Manual</strong> Version 8.21 3-2