AT+i Programmer's Manual - SE Spezial-Electronic AG

More documents

Recommendations

Info

Nonvolatile Parameter Database 33.3.19 +iCKSM — Checksum Mode Syntax: AT+iCKSM= Sets iChip‘s checksum mode. With this mode enabled, iChip calculates the checksum of data it returns to host upon receiving the AT+iSRCV command. At the same time, iChip expects the host to append checksum to the data it sends with the AT+iSSND command. iChip compares the checksum it calculates with the one calculated by the host to verify that data was not corrupted during transmission between host and iChip. Parameters: n=0 | 1 Command Options: n=0 Checksum mode disabled n=1 Checksum mode enabled Default: n=0 (checksum mode disabled) Result code: I/OK If n is either ‗0‘ or ‗1‘. I/ERROR Otherwise
33.4 ISP Connection Parameters 33.4.1 +iISPn — Set ISP Phone Number Syntax: AT+iISPn=dial-s Parameters: n=1..2 Command Options: Sets the ISP‘s access phone numbers. Nonvolatile Parameter Database Use n=1 to set the ISP‘s primary access phone number. Use n=2 to set the ISP‘s alternate number. The alternate number is dialed after exhausting all redial attempts of the primary number. dial-s= Telephone number string, composed of digits, ‗,‘, ‗-‘, ‗W‘, ‗w‘, ‗*‘, ‗#‘, ‗!‘ or ‗ ‘. See description of the standard ATD command. Note: If a character that is defined as a delimiter is used within the dial string, the string must be entered between apostrophes. dial-s=‗ ‘ Empty access number dial-s= number will be set as ISP access number Default: Empty. No permanent ISP access number defined. Result Code: I/OK If dial-s is a legal phone number string. I/ERROR Otherwise AT+iISPn~dial-s Temporarily sets the ISP‘s primary/alternate access number. The permanent value will be restored after completing the session, whether the session was successful or not. AT+iISPn? Reports the current value of the ISP's primary/alternate access numbers. If the number does not exist, only is returned. The reply is followed by I/OK. AT+iISPn=? Returns the message ―Phone #‖ followed by I/OK.
Page 1 and 2:
Pub. No. 20-5000-08_21, January 200
Page 3 and 4:
Revision History 20-5000-08_21 Revi
Page 5 and 6:
Contents 10.1 +IWWW — ACTIVATE EM
Page 7 and 8:
Contents 25.3 HEADER PARAMETER NAME
Page 9 and 10:
Contents 33.4.5 +iRDL — Number of
Page 11 and 12:
Contents 33.17.2 +iDSLT — DHCP Se
Page 13 and 14:
Tables Tables Table 2-1 AT+i Comman
Page 15 and 16:
AT+i Command Set If a syntax error
Page 17 and 18:
2 General Format AT+i[[ | #UFn]…]
Page 19 and 20:
General Format Command Function Par
Page 21 and 22:
General Format Command Function Par
Page 23 and 24:
AT+i Result Code Summary 85 RESERVE
Page 25 and 26:
4 Report Status 4.1 +iRPi — Repor
Page 27 and 28:
Report Option Format 10 I/(, , , )
Page 29 and 30:
5 Connection 5.1 +iBDRA — Forces
Page 31 and 32:
5.3 +iTUP — Triggered Internet Se
Page 33 and 34:
5.4 +iDOWN — Terminate Internet S
Page 35 and 36:
6 E-mail Send Commands E-mail Send
Page 37 and 38:
Notes: E-mail Send Commands I/OK If
Page 39 and 40:
7 E-Mail Retrieve 7.1 +iRML — Ret
Page 41 and 42:
7.3 +iRMM — Retrieve Mail Message
Page 43 and 44:
E-Mail Receive (RMM) Flow Diagram I
Page 45 and 46:
-or- specified. HTTP Client Interfa
Page 47 and 48:
9 SerialNET Mode Initiation 9.1 +iS
Page 49 and 50:
10 Web Server Interface 10.1 +iWWW
Page 51 and 52:
11 File Transfer Protocol (FTP) 11.
Page 53 and 54:
11.3 +iFDNL — FTP Directory Names
Page 55 and 56:
11.5 +iFCWD — FTP Change Working
Page 57 and 58:
11.7 +iFRCV — FTP Receive File Sy
Page 59 and 60:
11.9 +iFAPN — FTP Open File for A
Page 61 and 62:
11.11 +iFCLF — FTP Close File Syn
Page 63 and 64:
11.13 +iFCLS — FTP Close Session
Page 65 and 66:
12.2 +iTRCV — Telnet Receive Data
Page 67 and 68:
12.4 +iTBSN[%] — Telnet Send A By
Page 69 and 70:
12.6 +iTCLS — Telnet Close Sessio
Page 71 and 72:
13.2 +iSUDP — Open A Connectionle
Page 73 and 74:
Direct Socket Interface 13.4 +iLSST
Page 75 and 76:
13.6 +iSCS — Get A Socket Connect
Page 77 and 78:
Result Code: Direct Socket Interfac
Page 79 and 80:
Direct Socket Interface I/ERROR If
Page 81 and 82:
13.10 +iSDMP — Dump Socket Buffer
Page 83 and 84:
13.12 +iSCLS — Close Socket Synta
Page 85 and 86:
15 Wireless LAN Mode Wireless LAN M
Page 87 and 88:
16 IP Registration IP Registration
Page 89 and 90:
17 DHCP Client DHCP Client A DHCP c
Page 91 and 92:
19 Ad-Hoc Networks Ad-Hoc Networks
Page 93 and 94:
20 Secure Socket Protocol Secure So
Page 95 and 96:
Secure Socket Protocol When the AT+
Page 97 and 98:
20.6 +i[@]FOPS — Secure FTP Open
Page 99 and 100:
22 MIME Encapsulated E-Mail Message
Page 101 and 102:
22.3 MIME-Encapsulated E-Mail Messa
Page 103 and 104:
The control characters are defined
Page 105 and 106:
23.3 Software Flow Control During A
Page 107 and 108:
23.5 Host iChip Hardware Flow Cont
Page 109 and 110:
Remote Firmware Update 2. If the do
Page 111 and 112:
25 iChip Parameter Update 25.1 Intr
Page 113 and 114:
25.4 Uploading A Parameters Update
Page 115 and 116: 26.3 Web Server Modes Two web serve
Page 117 and 118: 26.7 Host Interaction Mode iChip Em
Page 119 and 120: ~headline~ iChip Embedded Web Ser
Page 121 and 122: iChip Embedded Web Server Tags. Thi
Page 123 and 124: 27.3 RAS Theory of Operation iChip
Page 125 and 126: 28 SerialNET Theory of Operation 28
Page 127 and 128: SerialNET Theory of Operation bytes
Page 129 and 130: SerialNET Theory of Operation If th
Page 131 and 132: Accumulate Quiet Time 29.5 FTP Rece
Page 133 and 134: Secure Socket Protocol Theory of Op
Page 135 and 136: [ CA_default_policy ] commonName =
Page 137 and 138: Secure Socket Protocol Theory of Op
Page 139 and 140: Remote AT+i Service iChip LAN will
Page 141 and 142: Nonvolatile Parameter Database Para
Page 147 and 148: 33.3 Operational Parameters 33.3.1
Page 149 and 150: 33.3.3 +iMIS — Modem Initializati
Page 151 and 152: 2. AT+iMIS=‖ 3. AT+iBDRF=3 4. AT+
Page 153 and 154: 33.3.6 +iTTO — TCP Timeout Syntax
Page 155 and 156: 33.3.8 +iMPS — Max PPP Packet Siz
Page 157 and 158: Nonvolatile Parameter Database 33.3
Page 161 and 162: 33.3.14 +iFLW — Set Flow Control
Page 163 and 164: 33.3.16 +iPSE — Set Power Save Mo
Page 165: 33.3.18 +iDF — IP Protocol ‘Don
Page 169 and 170: 33.4.3 +iUSRN — Define Connection
Page 171 and 172: 33.4.5 +iRDL — Number of Times to
Page 173 and 174: 33.5 Server Profile Parameters 33.5
Page 175 and 176: 33.5.3 +iSMTP — Define SMTP Serve
Page 179 and 180: 33.5.7 +iPOP3 — Define POP3 Serve
Page 189 and 190: 33.7 Email Format Parameters Nonvol
Page 193 and 194: 33.7.4 +iDELF — Email Delete Filt
Page 195 and 196: 33.7.6 +iTOA — Define Primary Add
Page 197 and 198: 33.7.8 +iREA — Return Email Addre
Page 199 and 200: 33.7.10 +iCCn — Define Alternate
Page 201 and 202: 33.7.12 +iMST — Media Subtype Str
Page 203 and 204: 33.8 HTTP Parameters Nonvolatile Pa
Page 207 and 208: 33.9 RAS Server Parameters Nonvolat
Page 209 and 210: 33.9.3 +iRAP — Password for RAS A
Page 211 and 212: 33.10.2 +iDIP — iChip Default IP
Page 213 and 214: 33.10.4 +iIPG — IP Address of the
Page 215 and 216: 33.11 Wireless LAN Parameters 33.11
Page 217 and 218:
33.11.3 +iWLWM — Wireless LAN WEP
Page 219 and 220:
33.11.5 +iWLKn — Wireless LAN WEP
Page 221 and 222:
33.11.7 +iWLPP — Personal Shared
Page 223 and 224:
33.12 IP Registration Parameters No
Page 225 and 226:
Nonvolatile Parameter Database 33.1
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
33.16 Secure Socket Protocol Parame
Page 251 and 252:
33.16.3 +iCERT — Define SSL3/TLS1
Page 253 and 254:
33.17 DHCP Server Parameters Nonvol
Page 255 and 256:
34 Appendix A 34.1 MIME content typ
Page 257 and 258:
Type Subtype image jpeg gif ief g3f
Page 259 and 260:
MT=0 MST=‖text-plain‖ # CONNECT
Page 261 and 262:
37 Index +i!RP11 - Ad-Hoc Network R
Page 263:
Header Parameter Names and Values .
show all

AT+i Programmer's Manual - SE Spezial-Electronic AG

Create successful ePaper yourself

Delete template?

Save as template?