String Book - Logan Oil Tools
String Book - Logan Oil Tools String Book - Logan Oil Tools
70 tUBing maKe-Up torQUe hyDRIL CFJ-p tuBIng MInIMuM MAkE-up toRQuE * o.D. Weight grade — torque (ft-Ib) (in) (Ib/ft) J-55 C-75, L-80, n-80 & p- 05 2.375 4.7 & 5.3 800 1,100 2.875 6.5 1,100 1,500 3.500 9.3 & 10.3 1,500 1,900 4.000 11.0 2,000 2,700 4.500 12.75 3,000 4,000 5.000 23.2 4,500 6,000 * Data reprinted from Hydril Company 1984 Catalogue. Hydril recommends using a figure of 12-1/2% over minimum to ensure that minimum torque is obtained, since many factors influence torque application. Torque should never exceed 25% over minimum.
tUBing maKe-Up torQUe MAnnESMAnn tDS RECoMMEnDED MAkE-up toRQuE * o.D. Weight torque (ft-Ib) (in) (Ib/ft) grade Minimum Maximum K-55 1,100 4.6 C-75, N-80, 950 1,250 C-90, C-95, 1,300 P-105 1,400 2.375 K-55 1,250 5.8 C-75, N-80, 1100 1,500 C-90, C-95, 1,650 P-105 1,800 K-55 1,500 6.4 C-75, N-80, 1400 1,800 C-90, C-95, 2,000 P-105 2,200 2.875 K-55 2,000 8.6 C-75, N-80, 1,600 2,500 C-90, C-95, 2,700 P-105 2,900 K-55 2,500 9.2 C-75, N-80, 2,200 3,000 C-90, C-95, 3,300 P-105 3,600 K-55 2,700 3.500 10.2 C-75, N-80, 2,400 3,500 C-90, C-95, 3,900 P-105 4,300 K-55 3,600 12.7 C-75, N-80, 2,900 4,600 C-90, C-95, 5,200 P-105 5,800 K-55 2,900 4.000 11.0 C-75, N-80, 2,300 3,600 C-90, C-95, 4,000 P-105 4,300 K-55 3,500 12.6 C-75, N-80, 2,300 4,300 C-90, C-95, 4,800 P-105 5,200 K-55 3,600 4.500 13.5 C-75, N-80, 2,500 4,600 C-90, C-95, 5,000 P-105 5,400 K-55 2,700 5,100 15.1 C-75, N-80, 4,000 6,900 C-90, C-95, 4,700 7,600 P-105 5,400 8,300 7
- Page 21 and 22: Logan LUBricateD fiShing BUmper SUB
- Page 23 and 24: api regULar — Union tooL regULar
- Page 25 and 26: api internaL fLUSh — hUgheS anD r
- Page 27 and 28: A pac .38 G D J C B E Diameter of s
- Page 29 and 30: hughES SLIM hoLE Size A B C D E F g
- Page 31 and 32: .1000 .0461 1/8 R 45° .015R A hUgh
- Page 33 and 34: 30° G A hyDriL jointS H - Threads
- Page 35 and 36: SeamLeSS DriLL pipe performance pro
- Page 37 and 38: api DriLL coLLar anD joint SizeS ±
- Page 39 and 40: DriLL coLLar torQUe recommenDationS
- Page 41 and 42: DriLL coLLar torQUe recommenDationS
- Page 43 and 44: DriLL coLLar torQUe recommenDationS
- Page 45 and 46: DriLL coLLar WeightS — poUnDS per
- Page 47 and 48: 20" +2 / -0 DriLL coLLar grooveS fo
- Page 49 and 50: WeB WiLSon ® forgeD LinKS A (Lengt
- Page 51 and 52: WeLD-on type tooL jointS maKe-Up to
- Page 53 and 54: WeLD-on type tooL jointS maKe-Up to
- Page 55 and 56: WeLD-on type tooL jointS maKe-Up to
- Page 57 and 58: tUBing maKe-Up torQUe non-upSEt REC
- Page 59 and 60: tUBing maKe-Up torQUe EXtERnAL upSE
- Page 61 and 62: tUBing maKe-Up torQUe nL AtLAS BRAD
- Page 63 and 64: tUBing maKe-Up torQUe nL AtLAS BRAD
- Page 65 and 66: tUBing maKe-Up torQUe nL AtLAS BRAD
- Page 67 and 68: tUBing maKe-Up torQUe ARMCo IJ nu-L
- Page 69 and 70: tUBing maKe-Up torQUe hyDRIL CS AnD
- Page 71: tUBing maKe-Up torQUe hyDRIL FJ tuB
- Page 75 and 76: tUBing maKe-Up torQUe VALLouREC VAM
- Page 77 and 78: atLaS BraDforD tUBing jointS A Size
- Page 79 and 80: tUBing preSSUre rating Internal yie
- Page 81 and 82: StanDarD SteeL pipe SizeS Standard
- Page 83 and 84: threaDeD anD coUpLeD-type caSing Si
- Page 85 and 86: threaDeD anD coUpLeD-type caSing Si
- Page 87 and 88: caSing maKe-Up torQUe — Short thr
- Page 89 and 90: caSing maKe-Up torQUe — Long thre
- Page 91 and 92: caSing maKe-Up torQUe — Long thre
- Page 93 and 94: caSing maKe-Up torQUe — Long thre
- Page 95 and 96: caSing Bit SizeS anD cLearanceS ApI
- Page 97 and 98: caSing Bit SizeS anD cLearanceS nAt
- Page 99 and 100: caSing Bit SizeS anD cLearanceS pIt
- Page 101 and 102: caSing Bit SizeS anD cLearanceS SpA
- Page 103 and 104: 120° KeLLy croSS-Section DimenSion
- Page 105 and 106: BUoyancy factor for SteeL pipe Flui
- Page 107 and 108: fLange DimenSionS StuDS, nutS, AnD
- Page 109 and 110: BrineLL harDneSS taBLe BRInELL ( ,0
- Page 111 and 112: Fraction Decimal (in) Millimeter 1/
- Page 113 and 114: torQUe oUtpUt With manUaL tongS LIn
- Page 115 and 116: proper pLacement of torQUe inDicato
- Page 117 and 118: Snub Line proper pLacement of torQU
- Page 119 and 120: eLevator anD tooL joint inSpection
- Page 121: Baash-Ross, Web Wilson, Hillman-Kel
tUBing maKe-Up torQUe<br />
MAnnESMAnn tDS RECoMMEnDED MAkE-up toRQuE *<br />
o.D. Weight torque (ft-Ib)<br />
(in) (Ib/ft) grade Minimum Maximum<br />
K-55 1,100<br />
4.6 C-75, N-80, 950 1,250<br />
C-90, C-95, 1,300<br />
P-105 1,400<br />
2.375 K-55 1,250<br />
5.8 C-75, N-80, 1100 1,500<br />
C-90, C-95, 1,650<br />
P-105 1,800<br />
K-55 1,500<br />
6.4 C-75, N-80, 1400 1,800<br />
C-90, C-95, 2,000<br />
P-105 2,200<br />
2.875 K-55 2,000<br />
8.6 C-75, N-80, 1,600 2,500<br />
C-90, C-95, 2,700<br />
P-105 2,900<br />
K-55 2,500<br />
9.2 C-75, N-80, 2,200 3,000<br />
C-90, C-95, 3,300<br />
P-105 3,600<br />
K-55 2,700<br />
3.500 10.2 C-75, N-80, 2,400 3,500<br />
C-90, C-95, 3,900<br />
P-105 4,300<br />
K-55 3,600<br />
12.7 C-75, N-80, 2,900 4,600<br />
C-90, C-95, 5,200<br />
P-105 5,800<br />
K-55 2,900<br />
4.000 11.0 C-75, N-80, 2,300 3,600<br />
C-90, C-95, 4,000<br />
P-105 4,300<br />
K-55 3,500<br />
12.6 C-75, N-80, 2,300 4,300<br />
C-90, C-95, 4,800<br />
P-105 5,200<br />
K-55 3,600<br />
4.500 13.5 C-75, N-80, 2,500 4,600<br />
C-90, C-95, 5,000<br />
P-105 5,400<br />
K-55 2,700 5,100<br />
15.1 C-75, N-80, 4,000 6,900<br />
C-90, C-95, 4,700 7,600<br />
P-105 5,400 8,300<br />
7