String Book - Logan Oil Tools
String Book - Logan Oil Tools String Book - Logan Oil Tools
8 Upper Eye Lower Eye forgeD LinKS Wear chart Thickness of wear point in Lower Eye Dimension (Dim.) “A” To determine the strength of worn links, measure the amount of eye wear with calipers as shown, and compare the figure with the table for the new capacity. Capacity of set is that of weakest eye. Measure the depth of the link ear at the point of the greatest wear (Dim. A). The new capacity of the hook and/or link ears is shown in corresponding chart of hook size. WEAR LIMItS: It is recommended that any hook showing wear of 1/2" be promptly repaired. Wear should never exceed 3/4". When properly built up to recommended dimensions, the wear pad will prevent further loss in capacity until original wear point is reached. The load capacity will always be that of greatest wear. Dim. A Decrease in strength of the hook by wear of link ears is shown for Web Wilson Hooks. B Thickness of wear point in Upper Eye Dimension (Dim. B) hyDRA-hook LInk EARS WEAR ChARt A upper Lower Capacity Eye Eye (per set) Dim. A Dim. B tons - / in – 50 tons 3-1/2 1-3/4 150 3-3/8 1-5/8 125 3-1/4 1-9/16 110 3-1/8 1-1/2 100 - / in – 50 tons 5 2-1/4 250 4-3/4 2-1/8 210 4-5/8 2-1/2 188 4-1/2 2 175 - / in – 50 tons 5 2-3/4 350 4-3/4 2-5/8 290 4-5/8 2-1/2 262 4-1/2 2-7/16 245 - / in – 500 tons 6 3-1/2 500 5-5/8 3-1/4 440 5-1/4 3 375 5-3/16 2-7/8 345 Dim. Remaining Dim. Remaining A Capacity A Capacity (in) (tons) (in) (tons) 0-ton hook 50-ton hook 3-3/8 40 7-3/8 250 3-1/8 35 7-1/8 230 2-7/8 31 6-7/8 203 2-5/8 25 6-5/8 187 65-ton hook 50-ton hook 3-7/8 65 7-3/8 350 3-5/8 58 7-1/8 318 3-3/8 51 6-7/8 286 3-1/8 40 6-5/8 254 00-ton hook 500-ton hook 4-3/8 100 7-7/8 500 4-1/8 91 7-5/8 450 3-7/8 79 7-3/8 400 3-5/8 64 7-1/8 350 50-ton hook 4-7/8 150 4-5/8 138 4-3/8 123 4-1/8 112
Baash-Ross, Web Wilson, Hillman-Kelley, KelCo, Larkin, Hydra-Hook, Champion, Fulgrip, Foster, Thornhill Craver, Tri-Kelly, Pow-R-Seal, Saf-T-Seal, DynaSeal, DynaCentric, Pow-R-Gard, Saf-T- Gard, UNIBOLT, and Ouadbolt are registered trademarks or tradenames of Cooper Industries, Inc., Houston, Texas. Armco, Seal-Lock, EXTREME LINE, IJ NU-Lock, and NU-Lock are registered trademarks and/or trade names of Armco, Inc., Middletown, Ohio. Atlas Bradford is a registered trademark of Tenaris Oilfield Services, Luxembourg. Hughes is a registered trademark of Baker Hughes Incorporated, Houston, Texas. Hydril, CS, CTS-CB, CFJP-CB, A95-CB, CS-CB, CTS, Triple Seal, Triple Seal II, PH4-CB, and PH6-CB are registered trademarks of Hydril Company, Houston, Texas. Mannesmann and VAM are registered trademarks of Vallourec & Mannesmann (V&M) Tubes, Boulogne, France. 9
- Page 69 and 70: tUBing maKe-Up torQUe hyDRIL CS AnD
- Page 71 and 72: tUBing maKe-Up torQUe hyDRIL FJ tuB
- Page 73 and 74: tUBing maKe-Up torQUe MAnnESMAnn tD
- Page 75 and 76: tUBing maKe-Up torQUe VALLouREC VAM
- Page 77 and 78: atLaS BraDforD tUBing jointS A Size
- Page 79 and 80: tUBing preSSUre rating Internal yie
- Page 81 and 82: StanDarD SteeL pipe SizeS Standard
- Page 83 and 84: threaDeD anD coUpLeD-type caSing Si
- Page 85 and 86: threaDeD anD coUpLeD-type caSing Si
- Page 87 and 88: caSing maKe-Up torQUe — Short thr
- Page 89 and 90: caSing maKe-Up torQUe — Long thre
- Page 91 and 92: caSing maKe-Up torQUe — Long thre
- Page 93 and 94: caSing maKe-Up torQUe — Long thre
- Page 95 and 96: caSing Bit SizeS anD cLearanceS ApI
- Page 97 and 98: caSing Bit SizeS anD cLearanceS nAt
- Page 99 and 100: caSing Bit SizeS anD cLearanceS pIt
- Page 101 and 102: caSing Bit SizeS anD cLearanceS SpA
- Page 103 and 104: 120° KeLLy croSS-Section DimenSion
- Page 105 and 106: BUoyancy factor for SteeL pipe Flui
- Page 107 and 108: fLange DimenSionS StuDS, nutS, AnD
- Page 109 and 110: BrineLL harDneSS taBLe BRInELL ( ,0
- Page 111 and 112: Fraction Decimal (in) Millimeter 1/
- Page 113 and 114: torQUe oUtpUt With manUaL tongS LIn
- Page 115 and 116: proper pLacement of torQUe inDicato
- Page 117 and 118: Snub Line proper pLacement of torQU
- Page 119: eLevator anD tooL joint inSpection
Baash-Ross, Web Wilson, Hillman-Kelley, KelCo, Larkin, Hydra-Hook, Champion, Fulgrip, Foster,<br />
Thornhill Craver, Tri-Kelly, Pow-R-Seal, Saf-T-Seal, DynaSeal, DynaCentric, Pow-R-Gard, Saf-T-<br />
Gard, UNIBOLT, and Ouadbolt are registered trademarks or tradenames of Cooper Industries, Inc.,<br />
Houston, Texas.<br />
Armco, Seal-Lock, EXTREME LINE, IJ NU-Lock, and NU-Lock are registered trademarks and/or<br />
trade names of Armco, Inc., Middletown, Ohio.<br />
Atlas Bradford is a registered trademark of Tenaris <strong>Oil</strong>field Services, Luxembourg.<br />
Hughes is a registered trademark of Baker Hughes Incorporated, Houston, Texas.<br />
Hydril, CS, CTS-CB, CFJP-CB, A95-CB, CS-CB, CTS, Triple Seal, Triple Seal II, PH4-CB, and<br />
PH6-CB are registered trademarks of Hydril Company, Houston, Texas.<br />
Mannesmann and VAM are registered trademarks of Vallourec & Mannesmann (V&M) Tubes,<br />
Boulogne, France.<br />
9