air venturi powered single compartment sump sucker - Master ...

More documents

Recommendations

Info

SPARE PARTS LIST – AIR VENTURI SUMP CLEANERS PART NO DESCRIPTION NOTES 54-1200 Venturi Exhaust silencer 54-1220 Venturi Powerhead o-ring 41-2090 Orange Discharge Hose, 1-1/2” Dia. Sold by the foot 41-2110 Orange Suction Hose, 2” Dia. Sold by the foot 42-1140 1-1/2” Male QD X Hose Shank 42-1200 1-1/2” Fem QD X 1” Fem NPT 42-1220 1-1/2” Hose barb 42-0133 2” Fem QD X Hose Shank 42-0132 2” Male QD X Male NPT 60-1960 1” NPT Discharge Nozzle (Also see assemblies) 60-1520 t Manhole/Cleanout Gasket – 14: dia Round— S/N 3312 to Present 60-1140 Basket Retaining Ring 60-1560 Top Gasket - Basket 60-1460 Poly Filter Sleeve - 63” X 48”L 60-1480 Paper Filter Bag - 63” X 48”L 43-1060 Swivel Caster - 4” Dia X 2”W 43-1240 Wheel - 12” Dia X 3”W X 1-1/4” 3457 to Present 60-1260 18” Suction Tool - 2” Dia. 60-1220 36” Suction Tool - 2” Dia. 60-1360. 36” Crevice Tool - 2” Dia 38-1141 Plastic Float Ball 60-1980 1” Discharge Nozzle Assembly 60-1100 24” Sludge Basket Assembly Used on 100 gallon tanks 60-1080 36” Sludge Basket Assembly OPTION EQUIPMENT - SUMP SUCKER Spare Parts For Truck Mounted Rectangular Sump Cleaner (S/N 3346 on): 60-1540 Cleanout Gasket 3/8” x 15” x 21” (rectangular) Spare Parts For Tow Around Sump Cleaner: 43-1140 Wheel/Caster - 8” diameter x 3” wide rigid (400 total gallons or less) 43-1160 Wheel/Caster - 8” diameter x 3” wide swivel (400 total gallons or less) 43-1180 Wheel/Caster - 10” diameter x 4” wide rigid (500 total gallons or more) 43-1200 Wheel/Caster - 10” diameter x 4” wide swivel (500 total gallons or more) Page 18 of 20
SUMP CLEANER TROUBLESHOOTING CHART PROBLEM PART TO CHECK POSSIBLE SOLUTION Insufficient suction or no suction 1. Basket 1A. Check for full basket; empty 1B. Check if basket is blinded off; clean or replace 2. Hoses 2A. Check for obstructions; physically remove 2B. Check for cracks or holes; replace 3. Air leakage 3. Check all hose connections for tightness; make sure female quick disconnect fittings have gaskets in place; check top gasket on filter basket and repair or replace.” 4. Discharge nozzle 4. Check that discharge nozzle is fully closed and in place; switch to discharge mode 5. Air supply 5. Check air supply pressure; 100-125 PSI @ 20-30 CFM needed. Check supply hose diameter (3/8” hose with ¼” fittings required; 3/8” fittings recommended) 6. Air venturi silencer 6. Check silencer on air ventuir powerhead for blockage by dirt/oil; clean or replace Insufficient discharge 1. Suction valve 1. Check that suction inlet ball valve is fully closed 2. Regulator 2. Pressure regulator could be out of adjustment; contact a Service Technician at The Andersons Will not discharge 1. Discharge hose 1. Check hose for blockage; physically remove obstruction 2. Tank 2. Check for build up of fines and swarf in bottom of tank; clean as necessary 3. Discharge nozzle 3. Check to see if nozzle is plugged; physically remove obstruction. 4. Suction valve 4 Be sure suction ball valve is fully closed Excessive noise 1. Air venturi silencer 1. Check for liquid saturation; drain and dry or replace Portability 1. Hard to Push 1. Check for worn wheels or casters; replace 2. Check wheel and caster bearings; grease or replace 3. Rough floors; use a forklift truck for transport ALWAYS CHECK YOUR MANUAL FOR OPERATION INSTRUCTIONS AND MAINTENANCE This unit is Supplied by Page 19 of 20
Page 1 and 2: AIR VENTURI POWERED SINGLE COMPARTM
Page 3 and 4: SAFETY INFORMATION 1. To avoid poss
Page 5 and 6: PRESSURIZATION SAFETY ISSUES Your Y
Page 7 and 8: OPERATOR SAFETY AND CONVENIENCE FEA
Page 9 and 10: 2. For units mounted on mobile plat
Page 11 and 12: ASSEMBLY 1. Refer to the drawings a
Page 13 and 14: F. Discharge valve D1 is a three-wa
Page 15 and 16: • When vacuuming out machines usi
Page 17: 5. If the filter sleeve is maintain

air venturi powered single compartment sump sucker - Master ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?