Legacy® PLUS - Smiths Medical

More documents

Recommendations

Info

Pump Setup & Programming Section 2: Pump Setup and Programming Stopping the pump during the KVO will not affect the start time of subsequent doses.
3.0 Operating the Pump Starting the Pump Section 3: Operating the Pump When you start the pump, programmed values will be automatically reviewed. Then fluid delivery will begin as programmed, and “RUN” will appear on the main screen. If the pump will not start, a message will appear on the display. Refer to the Messages and Alarms Table in Section 5. WARNING: Prior to starting infusion, inspect the fluid path for kinks, a closed clamp, or other upstream occlusions, and remove all air to prevent air embolism. An undetected upstream occlusion may result in under- or non-delivery of medication, and, depending upon the type of medication being delivered, could result in death or serious injury to the patient. Air embolism could result in death or serious injury to the patient. To start the pump 1. Press and hold ⁄. Three sets of dashes appear on the display; then they disappear one-by-one, each accompanied by a single beep. 2. Release ⁄ after the last set of dashes disappears, and the pump beeps. All of the programming screens appear for your review one after the other. Stopping the Pump Stopping the pump stops delivery. When the pump is stopped, STOPPED will appear on the main screen, and you will hear 3 beeps every 5 minutes. To stop the pump 1. Press and hold ⁄. Three sets of dashes will appear one-by-one on the pump’s display, each accompanied by a single beep. 2. Release ⁄ after the third set of dashes appears and the pump beeps. Operating the Pump
Page 1 and 2: Legacy Operator’s Manual CADD-Leg
Page 3 and 4: Read this entire Operator’s Manua
Page 5 and 6: • Do not use rechargeable NiCad o
Page 7 and 8: • Do not expose the pump to humid
Page 9 and 10: Table of Contents Warnings iii Caut
Page 11 and 12: 1.0 General Description Section 1:
Page 13 and 14: Symbols O Direct Current (Power Jac
Page 15 and 16: Section 1: General Description Desc
Page 17 and 18: Section 1: General Description WARN
Page 19 and 20: Lock Levels Section 1: General Desc
Page 21 and 22: 2.0 Pump Setup and Programming Inst
Page 23 and 24: Section 2: Pump Setup and Programmi
Page 27 and 28: Changing to Lock Level 0 (LL0) Sect
Page 29 and 30: Delivery Methods Section 2: Pump Se
Page 33 and 34: Programming Continuous Delivery Sec
Page 37 and 38: KVO Rate Section 2: Pump Setup and
Page 39 and 40: Programming Intermittent Delivery S
Page 41 and 42: • Press „. 11. Verify the Upstr
Page 43 and 44: Attaching a Cassette Section 2: Pum
Page 49 and 50: Setting the Lock Level for the Pati
Page 51: Section 2: Pump Setup and Programmi
Page 55 and 56: 4.0 Biomed Functions Overview: Acce
Page 57 and 58: Upstream Sensor On/Off Section 4: B
Page 59 and 60: 5.0 Reference Messages and Alarms,
Page 61 and 62: Section 5: Reference Messages and A
Page 63 and 64: Cleaning the Pump and Accessories S
Page 65 and 66: Section 5: Reference Exposure to Ra
Page 67 and 68: Section 5: Reference IEC 61000-4-4
Page 69 and 70: Section 5: Reference System Deliver
Page 71 and 72: Biomed Functions Air Detector .....
Page 73 and 74: Flow rate: Minimum Time Interval: 1
Page 75 and 76: Section 5: Reference WARNING: The P
Page 77 and 78: Recommended separation distances be
Page 79 and 80: Section 5: Reference the motor driv
Page 81 and 82: Data Handling Software Safety Featu
Page 83 and 84: Mechanical Inspection Section 5: Re
Page 85 and 86: Section 5: Reference • Press and
Page 87 and 88: Upstream Occlusion Sensor Test Sect
Page 89 and 90: Occlusion Pressure Range Test II De
Page 91 and 92: Accuracy Tests Gravimetric Accuracy
Page 93 and 94: Example: Predelivery Weight: 61.1 g
Page 95 and 96: Section 5: Reference 5. Program a C
Page 97 and 98: indicator light, 4 inspection proce
Page 99 and 100: E. Computer Program License: Sectio

Legacy® PLUS - Smiths Medical

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?