Legacy® PLUS - Smiths Medical

More documents

Recommendations

Info

Pump Setup & Programming Section 2: Pump Setup and Programming 3. To seat the tubing into the groove, gently pull the tubing, until it is under the retention nubs and flat in the groove. Retent on nubs 4. Connect the tubing to the patient’s infusion set or indwelling catheter. WARNING: Ensure that the entire fluid path is free of all air bubbles before connecting to the patient to prevent air embolism. Air embolism could result in death or serious injury to the patient. NOTE: If the fluid path contains an air eliminating filter, it is acceptable for air bubbles to be present on the vent side of the filter.
Setting the Lock Level for the Patient Section 2: Pump Setup and Programming The Lock Level must be changed to LL1 or LL2 to prevent the patient from having complete access to all programming and operating functions. NOTE: You may change the lock level at any time by stopping the pump and following the procedure below. To change the lock level 1. Press Œ. 2. The current lock level will appear. 3. Press ´ or Î until the desired lock level (LL1 or LL2) appears. 4. Press Œ again or ¤. “Code 0” will appear. 5. Press ´ or Î until ** Text Omitted ** 6. Press Œ or ¤ to set the new lock level. WARNING: Do not disclose to the patient the pump’s security codes or any other information that would allow the patient complete access to all programming and operating functions. Improper programming could result in death or serious injury to the patient. Pump Setup & Programming
Page 1 and 2: Legacy Operator’s Manual CADD-Leg
Page 3 and 4: Read this entire Operator’s Manua
Page 5 and 6: • Do not use rechargeable NiCad o
Page 7 and 8: • Do not expose the pump to humid
Page 9 and 10: Table of Contents Warnings iii Caut
Page 11 and 12: 1.0 General Description Section 1:
Page 13 and 14: Symbols O Direct Current (Power Jac
Page 15 and 16: Section 1: General Description Desc
Page 17 and 18: Section 1: General Description WARN
Page 19 and 20: Lock Levels Section 1: General Desc
Page 21 and 22: 2.0 Pump Setup and Programming Inst
Page 23 and 24: Section 2: Pump Setup and Programmi
Page 27 and 28: Changing to Lock Level 0 (LL0) Sect
Page 29 and 30: Delivery Methods Section 2: Pump Se
Page 33 and 34: Programming Continuous Delivery Sec
Page 37 and 38: KVO Rate Section 2: Pump Setup and
Page 39 and 40: Programming Intermittent Delivery S
Page 41 and 42: • Press „. 11. Verify the Upstr
Page 43 and 44: Attaching a Cassette Section 2: Pum
Page 47: Section 2: Pump Setup and Programmi
Page 53 and 54: 3.0 Operating the Pump Starting the
Page 55 and 56: 4.0 Biomed Functions Overview: Acce
Page 57 and 58: Upstream Sensor On/Off Section 4: B
Page 59 and 60: 5.0 Reference Messages and Alarms,
Page 61 and 62: Section 5: Reference Messages and A
Page 63 and 64: Cleaning the Pump and Accessories S
Page 65 and 66: Section 5: Reference Exposure to Ra
Page 67 and 68: Section 5: Reference IEC 61000-4-4
Page 69 and 70: Section 5: Reference System Deliver
Page 71 and 72: Biomed Functions Air Detector .....
Page 73 and 74: Flow rate: Minimum Time Interval: 1
Page 75 and 76: Section 5: Reference WARNING: The P
Page 77 and 78: Recommended separation distances be
Page 79 and 80: Section 5: Reference the motor driv
Page 81 and 82: Data Handling Software Safety Featu
Page 83 and 84: Mechanical Inspection Section 5: Re
Page 85 and 86: Section 5: Reference • Press and
Page 87 and 88: Upstream Occlusion Sensor Test Sect
Page 89 and 90: Occlusion Pressure Range Test II De
Page 91 and 92: Accuracy Tests Gravimetric Accuracy
Page 93 and 94: Example: Predelivery Weight: 61.1 g
Page 95 and 96: Section 5: Reference 5. Program a C
Page 97 and 98: indicator light, 4 inspection proce
Page 99 and 100:
E. Computer Program License: Sectio
show all

Legacy® PLUS - Smiths Medical

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?