Legacy® PLUS - Smiths Medical

More documents

Recommendations

Info

Pump Setup & Programming Section 2: Pump Setup and Programming 0 5. Enter the Dose Cycle. • Press ´ or Î to select the desired cycle. • Press ¤. • Press „. 6. Enter the KVO rate. • Press ´ or Î to select the desired KVO rate. • Press ¤. • Press „. 7. Acknowledge Dose Remaining (if applicable). • Press „. 8. Enter a delay or “Immediate” for Dose Starts in _____ . • Press ´ or Î to select the desired amount of delay until the next dose (or “Immediate”). • Press ¤. • Press „. 9. Clear Given. • Press ¤ if you wish to clear the amount given. • Press „. 10. Verify the Air Detector status. • Make sure the desired setting is displayed. This screen will show whether the Air Detector is turned on (high or low) or off. WARNING: When the Air Detector is turned off, the pump will not detect air in the fluid path. Periodically inspect the fluid path and remove any air to prevent air embolism. Air embolism could result in death or serious injury to the patient. • If you need to change the Air Detector setting, see Section 4, Biomed Functions.
• Press „. 11. Verify the Upstream Sensor status. Section 2: Pump Setup and Programming • Make sure the desired setting is displayed. This screen will show whether the Upstream Occlusion Sensor is turned on or off. WARNING: When the Upstream Occlusion Sensor is turned off, the pump will not detect occlusions upstream (between pump and fluid container). Periodically inspect the fluid container for decreasing volume, inspect the fluid path for kinks, a closed clamp, or other upstream occlusions. Upstream occlusions could result in under- or non-delivery of medications. If undetected, these occlusions could result in death or serious injury to the patient. • If you need to change the Upstream Occlusion Sensor setting, see Section 4, Biomed Functions. • Press „. 12. Review the program. Press „ repeatedly to review the programming screens. If you need to reprogram a setting, press „ until the appropriate screen appears and change the setting as described in this section. Pump Setup & Programming
Page 1 and 2: Legacy Operator’s Manual CADD-Leg
Page 3 and 4: Read this entire Operator’s Manua
Page 5 and 6: • Do not use rechargeable NiCad o
Page 7 and 8: • Do not expose the pump to humid
Page 9 and 10: Table of Contents Warnings iii Caut
Page 11 and 12: 1.0 General Description Section 1:
Page 13 and 14: Symbols O Direct Current (Power Jac
Page 15 and 16: Section 1: General Description Desc
Page 17 and 18: Section 1: General Description WARN
Page 19 and 20: Lock Levels Section 1: General Desc
Page 21 and 22: 2.0 Pump Setup and Programming Inst
Page 23 and 24: Section 2: Pump Setup and Programmi
Page 27 and 28: Changing to Lock Level 0 (LL0) Sect
Page 29 and 30: Delivery Methods Section 2: Pump Se
Page 33 and 34: Programming Continuous Delivery Sec
Page 37 and 38: KVO Rate Section 2: Pump Setup and
Page 39: Programming Intermittent Delivery S
Page 43 and 44: Attaching a Cassette Section 2: Pum
Page 49 and 50: Setting the Lock Level for the Pati
Page 53 and 54: 3.0 Operating the Pump Starting the
Page 55 and 56: 4.0 Biomed Functions Overview: Acce
Page 57 and 58: Upstream Sensor On/Off Section 4: B
Page 59 and 60: 5.0 Reference Messages and Alarms,
Page 61 and 62: Section 5: Reference Messages and A
Page 63 and 64: Cleaning the Pump and Accessories S
Page 65 and 66: Section 5: Reference Exposure to Ra
Page 67 and 68: Section 5: Reference IEC 61000-4-4
Page 69 and 70: Section 5: Reference System Deliver
Page 71 and 72: Biomed Functions Air Detector .....
Page 73 and 74: Flow rate: Minimum Time Interval: 1
Page 75 and 76: Section 5: Reference WARNING: The P
Page 77 and 78: Recommended separation distances be
Page 79 and 80: Section 5: Reference the motor driv
Page 81 and 82: Data Handling Software Safety Featu
Page 83 and 84: Mechanical Inspection Section 5: Re
Page 85 and 86: Section 5: Reference • Press and
Page 87 and 88: Upstream Occlusion Sensor Test Sect
Page 89 and 90: Occlusion Pressure Range Test II De
Page 91 and 92:
Accuracy Tests Gravimetric Accuracy
Page 93 and 94:
Example: Predelivery Weight: 61.1 g
Page 95 and 96:
Section 5: Reference 5. Program a C
Page 97 and 98:
indicator light, 4 inspection proce
Page 99 and 100:
E. Computer Program License: Sectio
show all

Legacy® PLUS - Smiths Medical

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?