Legacy® PLUS - Smiths Medical

More documents

Recommendations

Info

Pump Setup & Programming Section 2: Pump Setup and Programming Continuous Rate Enter the continuous rate of medication delivery (in ml/hr). The maximum rate is 125 ml/hr. Given This screen shows the total amount of medication delivered since the last time the value was cleared. The amount shown is rounded to the nearest 0.05 ml. If this value reaches 99999.95, it automatically returns to 0 and continues counting. The Given amount does not include medication used when priming the tubing. Air Detector Status This screen indicates whether the Air Detector is on high sensitivity, low sensitivity or turned off. The Air Detector status cannot be changed without entering the Biomed Functions Code (see Section 4, Biomed Functions, to change the setting). Upstream Sensor Status This screen indicates whether the Upstream Occlusion Sensor is turned on or turned off. The Upstream Sensor status cannot be changed without entering the Biomed Functions Code (see Section 4, Biomed Functions, to change the setting). Before programming in Continuous Delivery Mode: • Stop the pump and change the Lock Level to LL0 as described in Section 1. • Select the Continuous Delivery Mode (CDM) as described in Changing the Delivery Methods in Section 4. If the pump is already in the CDM, you may select it again to clear all programming screens to their default settings.
Programming Continuous Delivery Section 2: Pump Setup and Programming WARNING: This pump delivers medication at a continuous rate or intermittent rate in milliliters per hour (ml/hr). Programming the pump at a delivery rate other than what is prescribed will cause over or under delivery of medication, which could result in patient injury or death. Be sure the pump is in the continuous delivery mode versus the intermittent delivery mode. To program the pump, enter the prescribed values. 1. Begin at the main screen. • Make sure the pump is in LL0. • Make sure STOPPED appears on the main screen. • Press „ to begin. 2. Enter the Reservoir Volume. • Press ´ or Î to select the volume of a filled fluid container. (If you do not wish to use the Reservoir Volume feature, scroll down to “Not In Use” located before 1.) • Press ¤. • Press „. 3. Enter the Continuous Rate. • Press ´ or Î to select the desired rate. • Press ¤. • Press „. 4. Clear Given. • Press ¤ if you wish to clear the amount given. • Press „. 5. Verify the Air Detector status. • Make sure the desired setting is displayed. This screen will show whether the Air Detector is turned on (high or low) or off. Pump Setup & Programming
Page 1 and 2: Legacy Operator’s Manual CADD-Leg
Page 3 and 4: Read this entire Operator’s Manua
Page 5 and 6: • Do not use rechargeable NiCad o
Page 7 and 8: • Do not expose the pump to humid
Page 9 and 10: Table of Contents Warnings iii Caut
Page 11 and 12: 1.0 General Description Section 1:
Page 13 and 14: Symbols O Direct Current (Power Jac
Page 15 and 16: Section 1: General Description Desc
Page 17 and 18: Section 1: General Description WARN
Page 19 and 20: Lock Levels Section 1: General Desc
Page 21 and 22: 2.0 Pump Setup and Programming Inst
Page 23 and 24: Section 2: Pump Setup and Programmi
Page 27 and 28: Changing to Lock Level 0 (LL0) Sect
Page 29 and 30: Delivery Methods Section 2: Pump Se
Page 31: Section 2: Pump Setup and Programmi
Page 37 and 38: KVO Rate Section 2: Pump Setup and
Page 39 and 40: Programming Intermittent Delivery S
Page 41 and 42: • Press „. 11. Verify the Upstr
Page 43 and 44: Attaching a Cassette Section 2: Pum
Page 49 and 50: Setting the Lock Level for the Pati
Page 53 and 54: 3.0 Operating the Pump Starting the
Page 55 and 56: 4.0 Biomed Functions Overview: Acce
Page 57 and 58: Upstream Sensor On/Off Section 4: B
Page 59 and 60: 5.0 Reference Messages and Alarms,
Page 61 and 62: Section 5: Reference Messages and A
Page 63 and 64: Cleaning the Pump and Accessories S
Page 65 and 66: Section 5: Reference Exposure to Ra
Page 67 and 68: Section 5: Reference IEC 61000-4-4
Page 69 and 70: Section 5: Reference System Deliver
Page 71 and 72: Biomed Functions Air Detector .....
Page 73 and 74: Flow rate: Minimum Time Interval: 1
Page 75 and 76: Section 5: Reference WARNING: The P
Page 77 and 78: Recommended separation distances be
Page 79 and 80: Section 5: Reference the motor driv
Page 81 and 82: Data Handling Software Safety Featu
Page 83 and 84:
Mechanical Inspection Section 5: Re
Page 85 and 86:
Section 5: Reference • Press and
Page 87 and 88:
Upstream Occlusion Sensor Test Sect
Page 89 and 90:
Occlusion Pressure Range Test II De
Page 91 and 92:
Accuracy Tests Gravimetric Accuracy
Page 93 and 94:
Example: Predelivery Weight: 61.1 g
Page 95 and 96:
Section 5: Reference 5. Program a C
Page 97 and 98:
indicator light, 4 inspection proce
Page 99 and 100:
E. Computer Program License: Sectio
show all

Legacy® PLUS - Smiths Medical

Create successful ePaper yourself

Delete template?

Save as template?