Legacy® PLUS - Smiths Medical

More documents

Recommendations

Info

Pump Setup & Programming Section 2: Pump Setup and Programming The Intermittent Delivery Mode (IDM) delivers a specified dose volume over a specified duration. You may repeat the dose in a cycle of up to 96 hours. The KVO feature allows you to deliver a minimal amount of medication between doses to maintain catheter patency. You may also delay the start of dose delivery using the “Dose Starts In” feature. Volume (ml) 0 Delay Start KVO Period Cycle Time KVO Period
Section 2: Pump Setup and Programming Programming Screens for Continuous Delivery These are the programming screens for the CADD-<strong>Legacy®</strong> <strong>PLUS</strong> pump, in the continuous delivery mode. Descriptions of the screens follow. Reservoir Volume Continuous Rate (ml/hr) Given Air Detector (Off, On-High, or On-Low) Upstream Sensor (Off or On) Reservoir Volume Reservoir Volume 100.0 ml Continuous Rate 5.0 ml/hr Given 2.50 ml Air Detector On-High Upstream Sensor On Enter the volume of fluid contained in a filled fluid container. The Reservoir Volume value decreases as the pump delivers fluid or as you prime the tubing. When you change the fluid container, reset the reservoir volume on this screen. If you do not wish to use the Reservoir Volume feature, scroll down to “Not In Use” (located before 1 and after 9999 in the range of values). The residual volume could be set higher than the capacity of the fluid container. Be sure to program the reservoir volume to reflect the actual volume of the medication being used. Pump Setup & Programming
Page 1 and 2: Legacy Operator’s Manual CADD-Leg
Page 3 and 4: Read this entire Operator’s Manua
Page 5 and 6: • Do not use rechargeable NiCad o
Page 7 and 8: • Do not expose the pump to humid
Page 9 and 10: Table of Contents Warnings iii Caut
Page 11 and 12: 1.0 General Description Section 1:
Page 13 and 14: Symbols O Direct Current (Power Jac
Page 15 and 16: Section 1: General Description Desc
Page 17 and 18: Section 1: General Description WARN
Page 19 and 20: Lock Levels Section 1: General Desc
Page 21 and 22: 2.0 Pump Setup and Programming Inst
Page 23 and 24: Section 2: Pump Setup and Programmi
Page 27 and 28: Changing to Lock Level 0 (LL0) Sect
Page 29: Delivery Methods Section 2: Pump Se
Page 33 and 34: Programming Continuous Delivery Sec
Page 37 and 38: KVO Rate Section 2: Pump Setup and
Page 39 and 40: Programming Intermittent Delivery S
Page 41 and 42: • Press „. 11. Verify the Upstr
Page 43 and 44: Attaching a Cassette Section 2: Pum
Page 49 and 50: Setting the Lock Level for the Pati
Page 53 and 54: 3.0 Operating the Pump Starting the
Page 55 and 56: 4.0 Biomed Functions Overview: Acce
Page 57 and 58: Upstream Sensor On/Off Section 4: B
Page 59 and 60: 5.0 Reference Messages and Alarms,
Page 61 and 62: Section 5: Reference Messages and A
Page 63 and 64: Cleaning the Pump and Accessories S
Page 65 and 66: Section 5: Reference Exposure to Ra
Page 67 and 68: Section 5: Reference IEC 61000-4-4
Page 69 and 70: Section 5: Reference System Deliver
Page 71 and 72: Biomed Functions Air Detector .....
Page 73 and 74: Flow rate: Minimum Time Interval: 1
Page 75 and 76: Section 5: Reference WARNING: The P
Page 77 and 78: Recommended separation distances be
Page 79 and 80: Section 5: Reference the motor driv
Page 81 and 82:
Data Handling Software Safety Featu
Page 83 and 84:
Mechanical Inspection Section 5: Re
Page 85 and 86:
Section 5: Reference • Press and
Page 87 and 88:
Upstream Occlusion Sensor Test Sect
Page 89 and 90:
Occlusion Pressure Range Test II De
Page 91 and 92:
Accuracy Tests Gravimetric Accuracy
Page 93 and 94:
Example: Predelivery Weight: 61.1 g
Page 95 and 96:
Section 5: Reference 5. Program a C
Page 97 and 98:
indicator light, 4 inspection proce
Page 99 and 100:
E. Computer Program License: Sectio
show all

Legacy® PLUS - Smiths Medical

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?