Sniffer Adaptive Application Analyzer: Adaptive Mode ... - NetScout
Sniffer Adaptive Application Analyzer: Adaptive Mode ... - NetScout Sniffer Adaptive Application Analyzer: Adaptive Mode ... - NetScout
EARLY FIELD TRIAL
EARLY FIELD TRIAL Setting Quick Select Options Overview 10 This section describes how to set Quick Select window preferences in the Quick Select > Options dialog box tabs. The Options dialog box has the following tabs: Setting General Tab Options on page 243 Setting Connection Tab Options on page 245 Setting Graph Tab Options on page 247 Setting Files Tab Options on page 248 Setting Aliases Tab Options on page 250 Setting Options in the Mining Options Tab on page 254 Setting General Tab Options Set the following options in the General tab: The Statistics Refresh option lets you select whether to refresh the Quick Select window’s statistics whenever you make changes in the Graph panel, such as move the time selector. The default setting is Off. The Merged Streams Message option enables or disables the pop-up warning that is generated when selecting two concurrent streams. The default setting is On. NOTE: Stream merging is not supported in Sniffer Adaptive Application Analyzer. The Stream Visibility option lets you indicate where to set the stream start time when first opening the stream: The earliest statistics-only data. This option exposes the history data at the beginning of a wrapped stream. In this case, the Data start time reflects the first instance of history data in the stream. The system defaults to this setting. User’s Guide 243
- Page 191 and 192: EARLY FIELD TRIAL Setting Display S
- Page 193 and 194: EARLY FIELD TRIAL Raw Capture Mode
- Page 195 and 196: EARLY FIELD TRIAL Table 8-9. Summar
- Page 197 and 198: EARLY FIELD TRIAL Raw Capture Mode
- Page 199 and 200: EARLY FIELD TRIAL Searching for Fra
- Page 201 and 202: EARLY FIELD TRIAL Raw Capture Mode
- Page 203 and 204: EARLY FIELD TRIAL Raw Capture Mode
- Page 205 and 206: EARLY FIELD TRIAL Raw Capture Mode
- Page 207 and 208: EARLY FIELD TRIAL Printing Decoded
- Page 209 and 210: EARLY FIELD TRIAL Using the Matrix
- Page 211 and 212: EARLY FIELD TRIAL Raw Capture Mode
- Page 213 and 214: EARLY FIELD TRIAL Using the Host Ta
- Page 215 and 216: EARLY FIELD TRIAL Using the Protoco
- Page 217 and 218: EARLY FIELD TRIAL Enabling VLAN Dat
- Page 219 and 220: EARLY FIELD TRIAL Expert Analysis O
- Page 221 and 222: EARLY FIELD TRIAL Expert Tool Bar T
- Page 223 and 224: EARLY FIELD TRIAL Expert Analysis
- Page 225 and 226: EARLY FIELD TRIAL Setting Expert Op
- Page 227 and 228: EARLY FIELD TRIAL Analyze Expert An
- Page 229 and 230: EARLY FIELD TRIAL Alarms Expert Ana
- Page 231 and 232: EARLY FIELD TRIAL Protocols To conf
- Page 233 and 234: EARLY FIELD TRIAL Subnet Masks To d
- Page 235 and 236: EARLY FIELD TRIAL To configure or d
- Page 237 and 238: EARLY FIELD TRIAL Oracle Options Mo
- Page 239 and 240: EARLY FIELD TRIAL IP Options Expert
- Page 241: EARLY FIELD TRIAL SECTION 4 Additio
- Page 245 and 246: EARLY FIELD TRIAL Setting Quick Sel
- Page 247 and 248: EARLY FIELD TRIAL Setting Graph Tab
- Page 249 and 250: EARLY FIELD TRIAL Setting Quick Sel
- Page 251 and 252: EARLY FIELD TRIAL Setting Quick Sel
- Page 253 and 254: EARLY FIELD TRIAL Figure 10-6. Addi
- Page 255 and 256: EARLY FIELD TRIAL Using the Address
- Page 257 and 258: EARLY FIELD TRIAL Using the Address
- Page 259 and 260: EARLY FIELD TRIAL SECTION 5 Reporti
- Page 261 and 262: EARLY FIELD TRIAL Running Reports O
- Page 263 and 264: EARLY FIELD TRIAL Table 12-1. Sprea
- Page 265 and 266: EARLY FIELD TRIAL Running Reports 4
- Page 267 and 268: EARLY FIELD TRIAL Index A About the
- Page 269 and 270: EARLY FIELD TRIAL Host Table, 212 m
- Page 271 and 272: EARLY FIELD TRIAL G General tab, 24
- Page 273 and 274: EARLY FIELD TRIAL option, 243 Mindi
- Page 275 and 276: EARLY FIELD TRIAL S S2DPalette.ini
- Page 277: EARLY FIELD TRIAL U Use Address Boo
EARLY FIELD TRIAL<br />
Setting Quick Select Options<br />
Overview<br />
10<br />
This section describes how to set Quick Select window preferences in the<br />
Quick Select > Options dialog box tabs. The Options dialog box has<br />
the following tabs:<br />
Setting General Tab Options on page 243<br />
Setting Connection Tab Options on page 245<br />
Setting Graph Tab Options on page 247<br />
Setting Files Tab Options on page 248<br />
Setting Aliases Tab Options on page 250<br />
Setting Options in the Mining Options Tab on page 254<br />
Setting General Tab Options<br />
Set the following options in the General tab:<br />
The Statistics Refresh option lets you select whether to refresh<br />
the Quick Select window’s statistics whenever you make changes<br />
in the Graph panel, such as move the time selector. The default<br />
setting is Off.<br />
The Merged Streams Message option enables or disables the<br />
pop-up warning that is generated when selecting two concurrent<br />
streams. The default setting is On.<br />
NOTE: Stream merging is not supported in <strong>Sniffer</strong> <strong>Adaptive</strong><br />
<strong>Application</strong> <strong>Analyzer</strong>.<br />
The Stream Visibility option lets you indicate where to set the<br />
stream start time when first opening the stream:<br />
The earliest statistics-only data. This option exposes the<br />
history data at the beginning of a wrapped stream. In this<br />
case, the Data start time reflects the first instance of history<br />
data in the stream. The system defaults to this setting.<br />
User’s Guide 243