Sniffer Adaptive Application Analyzer: Adaptive Mode ... - NetScout
Sniffer Adaptive Application Analyzer: Adaptive Mode ... - NetScout Sniffer Adaptive Application Analyzer: Adaptive Mode ... - NetScout
EARLY FIELD TRIAL Chapter 9 Figure 9-6. Protocols Tab To configure Expert Protocols: 232 Sniffer Adaptive Application Analyzer 1 Select Tools > Expert Options from the Quick Select window and the Expert UI Objects Properties window appears. 2 Select the Protocols tab and click the zero icon to expand/ collapse all the Expert layers. or Click the plus icon to open an Expert layer and show all the protocols. 3 Double click the Analyze cell and select:Yes to activate Expert Analysis for that protocol, or No to deactivate Expert Analysis for that protocol. 4 Click OK. Defining Protocols Use the Tools > Options Protocols tab to add and group upper-layer protocols and ports into user-defined groups. User-defined groups appear in the Post Analysis window for improved data assimilation and viewing efficiency.
EARLY FIELD TRIAL Subnet Masks To define protocols: Expert Analysis 1 Select Tools > Options from the Quick Select window and the Options window appears. 2 Enter a protocol name and port(s) in the appropriate tab. 3 Click OK. TCP/IP subnet masks traditionally reserve specific bits within an IP network address for the subnet mask depending on the class of address. The Expert comes with default subnet mask settings. Class A - 255.0.0.0 Class B - 255.255.0.0 Class C - 255.255.255.0 Certain networks may use nontraditional subnet masks. If the Expert is attached to a network segment that uses nontraditional subnet masks, it may register spurious network objects and diagnoses. This happens because the Expert expects address information at a location within the address field other than where it actually is. If your networks use nontraditional subnet masks, you must add the IP network address and appropriate subnet mask for the networks from which the Expert will see frames. User’s Guide 233
- Page 181 and 182: EARLY FIELD TRIAL Raw Capture Mode
- Page 183 and 184: EARLY FIELD TRIAL Raw Capture Mode
- Page 185 and 186: EARLY FIELD TRIAL Using the Manual
- Page 187 and 188: EARLY FIELD TRIAL 5 Click OK. Figur
- Page 189 and 190: EARLY FIELD TRIAL Raw Capture Mode
- Page 191 and 192: EARLY FIELD TRIAL Setting Display S
- Page 193 and 194: EARLY FIELD TRIAL Raw Capture Mode
- Page 195 and 196: EARLY FIELD TRIAL Table 8-9. Summar
- Page 197 and 198: EARLY FIELD TRIAL Raw Capture Mode
- Page 199 and 200: EARLY FIELD TRIAL Searching for Fra
- Page 201 and 202: EARLY FIELD TRIAL Raw Capture Mode
- Page 203 and 204: EARLY FIELD TRIAL Raw Capture Mode
- Page 205 and 206: EARLY FIELD TRIAL Raw Capture Mode
- Page 207 and 208: EARLY FIELD TRIAL Printing Decoded
- Page 209 and 210: EARLY FIELD TRIAL Using the Matrix
- Page 211 and 212: EARLY FIELD TRIAL Raw Capture Mode
- Page 213 and 214: EARLY FIELD TRIAL Using the Host Ta
- Page 215 and 216: EARLY FIELD TRIAL Using the Protoco
- Page 217 and 218: EARLY FIELD TRIAL Enabling VLAN Dat
- Page 219 and 220: EARLY FIELD TRIAL Expert Analysis O
- Page 221 and 222: EARLY FIELD TRIAL Expert Tool Bar T
- Page 223 and 224: EARLY FIELD TRIAL Expert Analysis
- Page 225 and 226: EARLY FIELD TRIAL Setting Expert Op
- Page 227 and 228: EARLY FIELD TRIAL Analyze Expert An
- Page 229 and 230: EARLY FIELD TRIAL Alarms Expert Ana
- Page 231: EARLY FIELD TRIAL Protocols To conf
- Page 235 and 236: EARLY FIELD TRIAL To configure or d
- Page 237 and 238: EARLY FIELD TRIAL Oracle Options Mo
- Page 239 and 240: EARLY FIELD TRIAL IP Options Expert
- Page 241 and 242: EARLY FIELD TRIAL SECTION 4 Additio
- Page 243 and 244: EARLY FIELD TRIAL Setting Quick Sel
- Page 245 and 246: EARLY FIELD TRIAL Setting Quick Sel
- Page 247 and 248: EARLY FIELD TRIAL Setting Graph Tab
- Page 249 and 250: EARLY FIELD TRIAL Setting Quick Sel
- Page 251 and 252: EARLY FIELD TRIAL Setting Quick Sel
- Page 253 and 254: EARLY FIELD TRIAL Figure 10-6. Addi
- Page 255 and 256: EARLY FIELD TRIAL Using the Address
- Page 257 and 258: EARLY FIELD TRIAL Using the Address
- Page 259 and 260: EARLY FIELD TRIAL SECTION 5 Reporti
- Page 261 and 262: EARLY FIELD TRIAL Running Reports O
- Page 263 and 264: EARLY FIELD TRIAL Table 12-1. Sprea
- Page 265 and 266: EARLY FIELD TRIAL Running Reports 4
- Page 267 and 268: EARLY FIELD TRIAL Index A About the
- Page 269 and 270: EARLY FIELD TRIAL Host Table, 212 m
- Page 271 and 272: EARLY FIELD TRIAL G General tab, 24
- Page 273 and 274: EARLY FIELD TRIAL option, 243 Mindi
- Page 275 and 276: EARLY FIELD TRIAL S S2DPalette.ini
- Page 277: EARLY FIELD TRIAL U Use Address Boo
EARLY FIELD TRIAL Chapter 9<br />
Figure 9-6. Protocols Tab<br />
To configure Expert Protocols:<br />
232 <strong>Sniffer</strong> <strong>Adaptive</strong> <strong>Application</strong> <strong>Analyzer</strong><br />
1 Select Tools > Expert Options from the Quick Select window and<br />
the Expert UI Objects Properties window appears.<br />
2 Select the Protocols tab and click the zero icon to expand/<br />
collapse all the Expert layers.<br />
or<br />
Click the plus icon to open an Expert layer and show all the<br />
protocols.<br />
3 Double click the Analyze cell and select:Yes to activate Expert<br />
Analysis for that protocol, or No to deactivate Expert Analysis for<br />
that protocol.<br />
4 Click OK.<br />
Defining Protocols<br />
Use the Tools > Options Protocols tab to add and group upper-layer<br />
protocols and ports into user-defined groups. User-defined groups<br />
appear in the Post Analysis window for improved data assimilation and<br />
viewing efficiency.