HANSER Hanser Publishers, Munich • Hanser Gardner Publications ...

More documents

Recommendations

Info

Pressure drop Ap (bar) Shear rate (s 1 ) LDPE m = 40 kg/h TM =160 0 C Length of flow path I (mm) Figure 5.9 Calculated pressure drop in a spider die with different die gaps used for blown film Figure 5.10 Shear rate along spider die LDPE TM =160°C hT =2 mm Length of flow path I (mm)
Residence time t (s) LDPE m = 40 kg/h TM =160 0 C /7r =2 mm Length of flow path I (mm) Figure 5.11 Residence time t of the melt as a function of the flow path I fa (1/s) P (bar) p: Total pressure drop ga: Shear rate in the gap outlet Spiral gap Pressure drop Die length (mm) 37.123 bar 54.88/s Figure 5.12 Results of simulation of a spiral die used for LLDPE blown film Shear rate in the gap inlet Spiral gap (mm)
Page 1 and 2:
Natti S. Rao Gunter Schumacher D e
Page 3 and 4:
Preface Today, designing of machine
Page 5 and 6:
Figure 1.1 Deformation of a Hookean
Page 7 and 8:
Figure 1.4 Shear flow The shear or
Page 9 and 10:
where c and m are empirical constan
Page 11 and 12:
Apparent viscosity 7\Q True viscosi
Page 13 and 14:
Pa Shear stress T Figure 1.11 Deter
Page 15 and 16:
Shift Factor for Crystalline Polyme
Page 17 and 18:
The power law exponent is obtained
Page 19 and 20:
1.3.7.5 Klein's Viscosity Formula [
Page 21 and 22:
where Mw = molecular weight JC —
Page 23 and 24:
Steady state shear compliance J°t
Page 25 and 26:
Ig 6\ Ig G" lga; Figure 1.22 Storag
Page 27 and 28:
Characterization of the Transient S
Page 29 and 30:
Time/ Figure 1.28 Tensile creep at
Page 31 and 32:
1.4.2.2 Nonlinear Viscoelastic Beha
Page 33 and 34:
Figure 1.37 Maxwell fluid [1 ] The
Page 35 and 36:
Die swel B1 Figure 1.40 Dependence
Page 37 and 38:
2 Thermodynamic Properties of Polym
Page 39 and 40:
where u = internal energy T = tempe
Page 41 and 42:
Enthalpy /7-/720 kWh kg Kl kg polyn
Page 43 and 44:
Table 2.1 Approximate Values for th
Page 45 and 46:
Analogous to Ohm's law in electric
Page 47 and 48:
Figure 3.3 One-dimensional heat tra
Page 49 and 50: Figure 3.5 Heat flow in a multilaye
Page 51 and 52: The combination of convection and c
Page 53 and 54: The equation for an infinite cylind
Page 55 and 56: The foregoing equations apply to ca
Page 57 and 58: Figure 3.11 Midplane temperature fo
Page 59 and 60: Figure 3.12 Temperature distributio
Page 61 and 62: For drag flow the velocity gradient
Page 63 and 64: Lewis number: ratio of thermal diff
Page 65 and 66: The Reynolds number ReL, based on t
Page 67 and 68: At thermal equilibrium according to
Page 69 and 70: The rate of heat generation in a pl
Page 71 and 72: The mass of the fluid permeating th
Page 73 and 74: 4 Designing Plastics Parts The defo
Page 75 and 76: The parabolic failure criterion is
Page 77 and 78: Figure 4.3 Secant modulus [4] Stres
Page 79 and 80: where P = load (N) Lybyd = dimensio
Page 81 and 82: 5 Formulas for Designing Extrusion
Page 83 and 84: for values of the ratio n (R0 + R1)
Page 85 and 86: melt density pm = 0.7 g/cm 3 Soluti
Page 87 and 88: and finally the pressure drop Ap fr
Page 89 and 90: Pressure drop Ap from Equation 5.2
Page 91 and 92: Proportionality factor K from Equat
Page 93 and 94: n = 3.043 RTh= 1.274 mm Shear rate
Page 95 and 96: The relation of a slit is H = heigh
Page 97 and 98: Shear stress (N/m 2 ) Figure 5.5 Ef
Page 99: Figure 5.7 Surface distortion on a
Page 103 and 104: Table 5.1 Dimensions of Square Scre
Page 105 and 106: Pressure drop in screen Mesh size F
Page 107 and 108: In practice, this efficiency is als
Page 109 and 110: 5.2.2 Melt Conveying Starting from
Page 111 and 112: md = 46.42 kg/h Equation 5.31 and E
Page 113 and 114: Solution Power Zc in the screw chan
Page 115 and 116: Indices: m: melt f: melt film b: ba
Page 117 and 118: Example with symbols and units a) S
Page 119 and 120: X- Q Figure 5.24 Velocity and tempe
Page 121 and 122: (5.54) As seen from the equations a
Page 123 and 124: Figure 5.26 Three-zone screw [8] Th
Page 125 and 126: The profiles of stock temperature a
Page 127 and 128: where HF = feed depth H = metering
Page 129 and 130: Screw speed (rpm) Screw diameter D
Page 131 and 132: 5.2.6 Mechanical Design of Extrusio
Page 133 and 134: Next Page Screw Vibration When the
Page 135 and 136: 5.3.1 Pressure Drop in Runner As th
Page 137 and 138: Examples of calculating pressure dr
Page 139 and 140: Example with symbols and units The
Page 141 and 142: Flow length L mm Spiral height H Fi
Page 143 and 144: Solution The conversion factors for
Page 145 and 146: Figure 5.43 shows a sample plot of
Page 147 and 148: With the values for the properties
Page 149 and 150: Cooling time mm Distance between mo
Page 151 and 152:
Table 5.2 Results of Optimization o
Page 153 and 154:
Per cent unmelted Axial distance al
Page 155 and 156:
A* [%] LDPE Axial length (screw dia
Page 157 and 158:
A* [%] A* [%] LDPE LDPE Axial lengt
Page 159 and 160:
Flow length (mm) Flow length (mm) F
Page 161 and 162:
Flow length L (mm) Flow length L (m
Page 163 and 164:
[26] VDI Warmeatlas, VDI Verlag, Du
Page 165 and 166:
A Final Word The aim of this book i
Page 167 and 168:
166 Index terms Links Index terms L
Page 169 and 170:
168 Index terms Links Index terms L
Page 171 and 172:
viii Contents 1.4 Viscoelastic Beha
Page 173 and 174:
x Contents 5.2 Extrusion Screws ...
show all

HANSER Hanser Publishers, Munich • Hanser Gardner Publications ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?