Catalogue 2012/2013 - Putzmeister MÃ¶rtelmaschinen GmbH

Top-Ouality 

Original Parts 

www.mortarmachines.com 

Mörtelmaschinen 

Plastering machines, screed conveyors and fine concrete pumps 

Catalogue 2012/2013

Our catalogue to help you in your work 

This year’s general catalogue presents the complete range from 

Putzmeister Mörtelmaschinen GmbH on over 70 pages. Here, you 

will find everything that we have to offer: floor screed conveyors, 

plastering machines, fine concrete pumps, and - of course - all of 

the appropriate accessories. 

Just look and you will find 

The chapter on each machine starts with a practical overview 

table. This allows us to guide you to the correct machine for the 

application. Then you can start looking at the right place in the 

catalogue. 

Each machine is described in detail, together with all the important 

technical data. Please note that we reserve the right to 

make technical changes. The stated performance specifications 

are guide values and are therefore not binding. All technical data 

may be changed without prior notice. 

Please note ... 

To ensure the correct and safe operation of the machine, 

please see the relevant operating manual. 

We would be happy to receive comments and suggestions 

about how we could design or structure the catalogue better in 

the future. Please write to: 

Putzmeister Mörtelmaschinen GmbH 

Key word: “Catalogue” 

Max-Eyth-Str. 10 · 72631 Aichtal, Germany 

If you want to find out more about us, feel free to get in touch: 

Telephone +49 (0) 71 27 5 99-0 

Or visit us on the Internet at: 


Edition: June 2012 

Floor screed conveyors 6 - 15 

Application overview for pneumatic conveyors 6 - 7 

Mixokret M 720 8 - 9 

Mixokret M 740 10 - 11 

Mixokret M 760 12 - 13 

Suggested accessories for floor screed conveyors 14 - 15 

Plastering machines 16 - 35 

Application overview for plastering machines 16 - 17 

Mixer pump MP 25 18 - 19 

Suggested accessories for MP 25 20 - 21 

Worm pump Sprayboy P 12 22 - 23 

Suggested accessories for Sprayboy P 12 24 - 25 

Worm pump S 5 + 26 - 27 

Suggested accessories for S 5 28 - 31 

Worm pump SP 11 Beliso 32 - 33 

Suggested accessories for SP 11 Beliso 34 - 35 

Fine concrete and self levelling floor screed pumps 36 - 51 

Application overview for piston pumps 36 - 37 

Piston pump P 13 38 - 39 

Suggested accessories for P 13 40 - 41 





Accessories for floor screed conveyors 52 - 55 

Accessories for plastering machines 56 - 67 

Accessories for fine concrete and self levelling screed pumps 68 - 70 

General accessories 71 - 72 

Conditions of sale and delivery 73 - 74 

3

Welcome to Putzmeister! 

The corporate site of the Putzmeister Group in Aichtal, near Stuttgart 

The Putzmeister Group 

We form part of the globally active Putzmeister group. With 

several subsidiaries around the world, this corporate group 

is represented in all global markets and is a real international 

player. 

Our main focuses are the manufacturing of machines to convey 

concrete, mortar, and high-density substances. In this way, 

companies of the Putzmeister group are active in business segments 

in many different areas: 

Concrete pumps 

Systems engineering 

Tunnelling machines 

Large robot technology 

Mortar machines 

We are based in Aichtal, near Stuttgart. This is where our headquarters are located – 

but our ideas for technical solutions are formulated on construction sites. That’s where 

it’s all about making work easier and more efficient. 

Whether you’re working with mortar, floor screed, or fine concrete, we can help with 

mixing, pumping, application, and spraying tasks. Practical innovations have made us 

great. And our machines are used throughout the world. 


We develop, produce, and supply one of the world’s most extensive ranges of powerful, 

site-optimized plastering machines, floor screed conveyors, and fine concrete pumps. 

As a wholly-owned subsidiary of the Putzmeister Group, we are able to offer you, 

our customers and sales partners, ideal conditions when it comes to expertise, 

investment security and optimum service in all sectors. 

The Putzmeister Building, where the administrative offices of 

Putzmeister Mörtelmaschinen GmbH are housed 

4

Quality “Made in Germany” 

Extremely modern production facilities in Aichtal, near Stuttgart 

The new assembly hall makes use of a line production system which is linked to 

numerous throughput stations. 

The production plant in Aichtal, near Stuttgart, covers around 9,000 m² and provides 

really modern conditions for the production of pneumatic conveyors, mixer pumps, 

piston pumps, and worm pumps. All work steps are standardized and guarantee consistently 

great quality with regard to processing and the performance of the finished 

products. 

Quality Assurance 

Our quality management measures start with the vitally important selection of 

ISO-certified suppliers and continue with the regular checking of these suppliers. 

Each machine is started up and tested immediately after assembly. If the test is 

successful, it is sent on for a final inspection. 

During the final production inspection, each machine is optimally adjusted one last 

time. We test our machines in continuous operation, checking all functions such as 

safety devices. In this way, we ensure that you receive a reliable Putzmeister product 

in perfect condition. 

Technology with more value 

However, sophisticated technology is not the whole story: in addition, we try to make 

sure that our contact with customers, sales partners, and suppliers is pleasant and 

beneficial for both sides. 

A wide network of competent and 

helpful sales partners 

Good quality, comprehensible 

technical documents 

A willingness to listen to questions 

and problems 

Fast, uncomplicated order processing 

Short delivery times for machines, 

spare parts, and wear parts 

Friendly and competent employees 

Fair pricing 

Investing in the future 

We also want to meet both our and your expectations in the future. This is why 

we continuously invest in qualified and committed employees. Excellent quality 

is simply not possible without them. 

We consistently continue to back the latest computerized plants and technology. 

Without them, it simply would not be possible to develop and manufacture top-quality 

products and to deliver them without faults. 

We also intensively cultivate contacts with our customers, suppliers, and sales 

partners throughout the world. 

5 

A total of 9,000 m² of space is available for the 

production of Putzmeister mortar machines in Aichtal. 

Our mixing tanks are welded at our own works using 

precise robotics and are then thoroughly checked using 

ultrasound methods. 

Guaranteed quality: our machines only use parts 

which have passed the most stringent quality controls 

and in-depth testing. 

Finishing: not one single machine leaves our 

production hall without being subjected to a thorough 

final inspection and careful cleaning.

Application overview for pneumatic conveyors 

Machines for conveying 

floor screed or sand 

For small or large construction sites, for fine or coarse materials, for 

short or long delivery distances: Putzmeister machines are powerful 

and really make work easier. 

Note: Always use a machine-compatible mortar in combination 

with machine technology. If you have any questions, please contact 

the material manufacturer or contact us directly. 

6 

Very 

Suitable – 

suitable 

Pneumatic conveyors 

M 720 

Pages 8 - 9 


M 740 

Pages 10 - 11 


M 760 

Pages 12 - 13 

in certain conditions 

Not 

suitable

Premixed dry mortar 

grain up to ~ 8 mm 

Conventional floor screed 

7 

Site-made mix 

grain up to ~ 16 mm 

Floor screed


Mixokret M 720 

The basic pneumatic conveyor 

The hydraulically driven M 720 combines all of the benefits 

of the Mixokret series in the smallest of spaces. The Mixokret 

M 720 is the ideal machine for small crews and lightweight 

tractor units. It is perfect for mixing and conveying floor 

screed, sand, gravel, and fine concrete up to a granulation of 

16 mm. 

Part no. 111 628.000 

8 

Robust 

plastic hood 

Environmentally 

friendly and powerful 

3-cylinder diesel motor 

Safe chassis 

Low-wearing 

mixing blades 

Mixer drum 

Skip loader

Technical data M 720 DH – standard M 720 DHB – skip loader 

Mixer drum 200 l, max. permissible internal pressure of 5 bar 

Theor. delivery rate* 3.0 m 3 /h 4.0 m 3 /h 

Delivery pressure 5 bar 5 bar 

Delivery distance* 100 m horizontal, 45 m vertical (15 storeys) 

Compressor air flow 2,750 l/min at 5 bar 

Drive motor 3-cylinder Kubota diesel motor, 22.5 kW at 2,300 rpm 

Weight 1,200 kg 1,280 kg 

Length x width x height 3,850 x 1,550 x 1,600 mm 3,940 mm x 1,550 x 2,450 mm 

Loader height (vertical) – 2,450 mm 

Filling height 900 mm 700 mm 

* The data is based on experience and depends on the materials used. 

The air cocks and pressure gauge are housed 

right near to the mixer drum. They allow you 

to make exactly the right setting every time. 

You control the machine using the control panel. 

Equipment M 720 DH – standard M 720 DHB – skip loader 

Standard colour paintwork 

Central mixer drum outlet 

Manual lid 

Centralized lubrication system 

High-pressure cleaner 

Car coupling 

Truck coupling 

2 additional bumped boiler ends Guard 

Customer labelling 

 

 

 

 

 

 

 

 

 

24 V light holder 

 

Key: – Not available Option Standard 

9 

Floor screed 

The water connection for the optional high-pressure cleaner is here. 

It cleans the machine quickly and reliably. There is no longer any need 

for the time-consuming scraping off of dried-on floor screed.



The all-rounder for all floor screed layers 

In a survey of 1,500 contractors, our Mixokret M 740 was 

named the best floor screed pump of 2012 in the professional 

journal “Fussbodentechnik”. 

It is easy to use, easy to service, and stylish. This real all-rounder 

is suitable for mixing and conveying floor screed, sand, gravel, 

and even fine concrete with a granulation of up to 16 mm. 

Part no. 111 629.000 

Drawbar can be lowered 

Intelligent air ducts 

Integrated 40 l toolbox 

Selectable hood colour (optional) 

Robust 

plastic hood 




10 

Safe chassis 

Scraper with 11 m cable Skip loader with 

260 l volume 

Low-wearing 

mixing blades 

Mixer drum with 

200 l usable volume

Technical data M 740 D – standard M 740 DB – skip loader M 740 DBS – skip loader + scraper 

Mixer drum 260 l, 200 l useful capacity, max. permissible internal pressure of 8 bar, TÜV-tested 

Theor. delivery rates* 3.8 m 3 /h 4.6 m 3 /h 5 m 3 /h 

Delivery pressure 8 bar 8 bar 8 bar 

Delivery distance* 180 m horizontal, 30 storeys vertical 

Compressor air flow 4.7 m 3 /min; cut-off pressure of 8 bar 

Drive motor 3-cylinder Deutz diesel motor, 33.5 kW at 2,500 rpm, emission category III A 

Chassis Fully galvanized, height-adjustable chassis (20 - 80 cm), approved for road use up to 80 km/h 

Weight (fully fuelled) 1,564 kg 1,786 kg 1,872 kg 

Length x width x height 4,605 x 1,500 x 1,585 mm 4,605 x 1,500 x 1,585 mm 4,605 x 1,500 x 1,585 mm 

Height (loader vertical) – 2,483 mm 2,820 mm 

Filling height 820 mm 600 mm 600 mm 


The control panel is designed to be 

clearly set out and is protected against 

contamination by means of a shutter. 


Special colour paintwork (hood) 


Manual lid 

Particle filter 


Working light 

Lifting eye 


Car coupling 



Mixing time adjustment 


Plastic storage box 


Key: 

The diesel motor has an inline design. 

This makes it tidier and easy to maintain. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

– Not available 

Option Standard 

11 

The height-adjustable drawbar is hot-dip 

galvanized, which provides sound protection 

against rust. 

Floor screed 

Optionally, we can paint 

the hood in the RAL 

colour of your choice. 

Equipment M 740 D – standard M 740 DB – skip loader M 740 DBS – skip loader + scraper



The powerful Mixokret – with a 46 kW diesel motor and hydraulic drive 

The M 760 is our most powerful Mixokret. It is practical, easy 

to operate, and easy to service. Like every Mixokret, this model 

is suitable for mixing and conveying floor screed, sand, gravel 

and fine grained concrete with a granulation of up to 16 mm. 

Part no. 111 630.000 

Drawbar can be lowered 

Intelligent air ducts 

Integrated 40 l toolbox 

Selectable hood colour 

(optional) 

Robust 

plastic hood 




12 

Safe chassis 

Scraper with 11 m cable Skip loader with 

260 l volume 

Low-wearing 

mixing blades 

Mixer drum with 

200 l usable volume

Technical data M 760 DH – standard M 760 DHB – skip loader M 760 DHBS – skip loader + scraper 

Mixer drum 260 l, 200 l useful capacity, max. permissible internal pressure of 8 bar, TÜV-tested 

Theor. delivery rate* 4 m 3 /h 4.8 m 3 /h 5 m 3 /h 

Delivery pressure 8 bar 8 bar 8 bar 

Delivery distance* 200 m horizontal, 50 storeys vertical 

Compressor air flow 5.0 m 3 /min, cut-off pressure of 8 bar 

Drive motor 4-cylinder Deutz diesel motor, 46 kW at 2,600 rpm (emission category III A) 

Chassis Fully galvanized, adjustable coupling height (20 - 80 cm), robust T-chassis 

Weight (fully fuelled) 1,600 kg 1,820 kg 1,900 kg 

Length x width x height 4,820 x 1,500 x 1,600 mm 4,820 x 1,500 x 1,600 mm 4,820 x 1,500 x 1,600 mm 

Loader height (vertical) – 2,480 mm 2,830 mm with scraper 

Filling height 820 mm 600 mm 600 mm 


The control panel is designed to be clearly 

set out and is protected against contamination 

by means of a shutter. 

The powerful, 4-cylinder diesel motor has an 

inline design. This makes it tidier and easy to 

maintain. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24V light holder 

 

Key: – Not available 


13 

The height-adjustable drawbar is hot-dip galvanized, 

which provides sound protection against 

rust. 

Floor screed 

Equipment M 760 DH – standard M 760 DHB – skip loader M 760 DHBS – skip loader + scraper 




Manual lid 



Conversion to 100 km/h 

Working light 

Lifting eye 


Car coupling 



Mixing time adjustment 


Plastic storage box 

Optionally, we can 

paint the hood in the 

RAL colour of your 

choice.


Suggested accessories for pneumatic conveyors 

Standard delivery line for Mixokret PM 50 / ID 50 mm (granulation of up to 8 mm*) 

Entire set, part no.: 533 089 

≈ 40 m long, consisting of: 

Part Part no. Fig. 

2x ID 50 mm hose, 10 bar, length of 20 m 501 915 10 

1x Discharge stand, 3 legs, aluminium ID 50 529 743 11 

2x O-ring 010 207.000 13 

6x Sponge ball, diameter of 60 mm 

for delivery hose ID 50 

000 212.005 14 

1x Reducer piece ID 65, KKV 70 / ID 50 071 790.006 

2x Rectangular gasket 213 266.000 

Delivery line KK 70 for Mixokret ID 65 mm (granulation of up to 12 mm*) 




8x ID 65 mm KK 70 hose, 10 bar, 10 m 456 831 10 

1x Discharge stand, 3 legs, aluminium KK 70 529 744 11 

8x O-ring 010 207.000 13 



000 246.000 14 





8x ID 65, KK 89 / HR hose, 10 bar, 10 m 443 675 9 

1x KKV 89 coupling 209 205.004 10 

1x Discharge stand, 3 legs, aluminium KK 89 529 745 11 

8x O-ring 002 224.004 13 


for delivery line ID 65 

000 246.000 14 

14 

10 

13 

13 

11 

10 14 

13 10 

14 

9 

* Depending on the material to be conveyed 

12 

11 

11 

14






1x Discharge stand, with runner, steel KK 89 529 748 12 

8x O-ring 002 224.004 13 



016 091.003 14 

1x Special outlet cpl. ID 90, KKV 89 073 640.002 15 

Delivery line KK 108 for Mixokret ID 90 mm (granulation of < 32 mm*) 





1x Discharge stand, with runner, steel KK 108 209 811.003 14 

1x Special outlet cpl. ID 90, KKV 108 419 634 15 



016 091.003 16 

8x O-ring 210 580.006 17 

15 

15 

13 

15 

17 

12 

10 14 

13 

Floor screed 

* Depending on the material to be conveyed 

16

Plastering machine application overview 

Machines for 

mortar and plaster 

Whatever you’re planning, the right Putzmeister machine will 

help you with the most varied of tasks in structural and civil 

engineering or in the construction industry in general. 

Mixer pumps 

MP 25 

Pages 18 - 19 

Worm pumps 

Sprayboy P 12 

Pages 22 - 23 

Worm pumps 

S 5 

Pages 26 - 27 

Worm pumps 

SP 11 

Pages 32 - 33 

Piston pumps 

P 13 

Pages 36 - 37 


with machine technology. In you have any questions, 

please contact the material manufacturer or contact us directly. 

Gypsum 

machine plaster 

Gypsum machine plaster 

– – 

– – 

– – 

– – 

16 

Gypsum/lime 

machine plaster 

Dry mortar (bag / silo / container material) 

Lime mortar 

Base coat plaster 

< 2 mm < 4 mm 

Lime and cement mortar 

Cement mortar 

Lime mortar 

Lime and cement mortar 

Cement mortar 

Lightweight plaster 

Insulating plaster

Very 

Suitable – 

Mineral 

cementitious 

adhesive 

Cementitious adhesive / 

reinforcement mortar 

suitable 

Dry mortar (bag / silo / container material) 

Acoustic spray plaster 


Rendering 

Spray plaster 

Textured plaster 

Scratch coats 

Fine 

plaster 

Felt and smooth plaster 

Not 

suitable 

Masonry 

mortar 

Fire 

protection 

mortar 

SPCC 

mortar 

– – – – – – – – – – – 

– – – – – – – 

– – – – 

– – – – – 

17 

Synthetic mortar / 

dispersion plaster 

Filler mortar 

All wet mortars 

(in containers 

or buckets) 

Textured plaster 

Cementitious adhesive 

Interior plaster 

(mixing ratio 

of 1:3) 

Lime plaster 

Mortar and plaster 

Site-made mixes 

Lime gypsum plaster 

External 

plaster 

(mixing ratio 

of 1:3) 

Lime cement plaster 

Cement plaster 

Masonry 

mortar

Mixer pumps 

Mixer pump MP 25 MIXIT 

The machine with the large reservoir for premixed dry mortar 

Easy to disassemble, but difficult 

to outperform. The reliable MP 25 is 

a real all-rounder. 

Suitable for all pumpable premixed dry 

mortar, whether it’s bag material or from 

a silo with a conveying system, e.g. 

interior plasters (gypsum and gypsum 

lime plaster), external plaster (lime, lime 

cement, and insulating plaster), self levelling 

floor screed, cementitious adhesive, 

and reinforcement mortar. Different 

pump parts and pump versions can vary 

the mix and pump output from around 5 

to 80 l/min. 

Conical mixing tube for 

optimum material flow 

Easily accessible flow meter for 

modifying the water ratio 

Integrated water pump 

18 

Powerful 

electric motor 

Reservoir hopper 

takes 115 l 

Integrated compressor 

with pressure cut-off 

MP 25 can be dismantled 

into manageable assemblies 

Compressed 

air remote control

Technical data MP 25 MIXIT – 3 x 400 V 50 HZ MP 25 MIXIT – 3 x 220 V 60 HZ 

Pump D6 Power D6 Power 

Theor. delivery rate* 25 l/min 25 l/min 


Delivery distance** Up to 40 m horizontal, 15 m vertical Up to 40 horizontal, 15 m vertical 

Air compressor 0.55 kW / 200 l/min – 

Pump drive 400 V / 50 Hz / 5.5 kW at 392 rpm 220 V / 60 Hz / 5.5 kW at 392 rpm 

Container drive 1.1 kW at 23 rpm 1.1 kW at 23 rpm 

Container content 115 l 115 l 

Water pump 0.78 kW at 3.4 m 3 /h 0.78 kW at 3.4 m 3 /h 

Weight 240 kg 245 kg 

Length x width x height 1,324 x 728 x 1,443 mm 1,324 x 728 x 1,443 mm 

Filling height 984 mm 984 mm 

Maximum particle size 4 mm 4 mm 

Pressure connections M35/V25-40 M35/V25-40 

Part no. 111 417.168 111 417.155 

* The delivery rate depends on the pump model. The delivery rate can vary in accordance with the pump used. 

**The data is based on experience and is dependent on the materials used. 

The large hopper and the low fill level 

make it distinctively more convenient and 

make your work easier. 

Equipment MP 25 MIXIT – 400 V MP 25 MIXIT – 220 V 


Water pump 

Compressor 

Suction hose for water pump 

Cable remote control + extension 

Uni remixer 

Insulating plaster attachment 

Air injection hood 

The material container and mixing tube are separated from each other. 

You open the gate valve and the material enters the mixing tube. 

 

 

 

 

 

 

 

 

Spacer plates 

 


19 


The MP 25 MIXIT can be dismantled into manageable 

and, more importantly, portable assemblies in no 

time at all.

Worm pumps 

Suggested accessories for MP 25 

Accessories for processing premixed dry mortar (impressive output of 40 l/min) 




1x Pump parts 

435 743 1 

– Screw conveyor D8-2 

– Screw conveyor barrel D8-2 

436 746 

1x Universal mixer shaft MP 25 211 773.003 2 

1x Spray gun, short and straight, V 35 203 054.002 3 

2x Mortar hose ID 35, 13.3 m long 207 615.007 4 

2x Air hose, 1/2", 20 m 001 665.004 5 

10x Sponge ball ID 35 065 044.001 6 

10x Seal ID 35 213 725.004 7 

3x Hose holder, leather 000 206.008 

Accessories for the processing of premixed dry mortar from a silo 





2x Air hose, 1/2", 20 m 001 665.004 2 

10x Seal ID 35 213 725.004 3 


1x Spray gun, short and straight V 35 203 054.002 5 

1x Feed hood with remote control cable 

Probe, rectangular 

212 324.008 6 


Accessories for processing premixed dry mortar 




2x Mortar hose ID 25-40, 10 m long 207 804.009 1 

1x Spray gun ID 25 402 592 2 

5x Seal ID 25 207 764.000 3 



20 

5 

2 

3 

3 

4 

1 

2 

7 

3 

5 

3 1 

4 3 

4 

6 

2 

7 

1 

6

Accessories for processing insulating plaster (impressive output of 40 l/min) 




1x Pump parts 

435 743 1 

– Screw conveyor D8-2 

– Screw conveyor barrel D8-2 

436 746 

1x Mixer shaft for insulating plaster MP 25 212 262.005 2 

1x Spray gun, with shut-off valve ID 35 209 174.009 3 


2x Air hose, 1/2", 20 m 001 665.004 4 


10x Seal ID 35 213 725.004 5 


1x Attachment collar for insulating plaster MP 25 212 325 007 7 



21 

8 

6 

4 

3 5 

8 

5 

6 

Accessories for processing cementitious adhesive, reinforcement mortar, and structural plaster 

(low output of 12 or 6 l/min) 


1x Pump parts 

214 402.009 1 

– Screw conveyor D4-1/2 

– Screw conveyor barrel D4-1/2 

214 403.008 

1x Cementitious adhesive mixer shaft 214 571.008 2 

1x Flow meter with range of 40 - 400 l/min 208 025.007 3 

1x Insertion nozzle, diameter of 4.5 x 55 mm 400 728 4 

2x Mortar hose ID 25-40, 10 m long 207 804.009 5 

1x Large fine plaster spray gun with PM coupling 

and Geka air connection 

529 733 8 

1x Air hose, 1/2", 20 m 001 665.004 11 


5x Seal ID 25 207 764.000 10 


10 

7 

11 

5 

9 

10 

2 

2 

1 

1 



1x Flow meter with range of 

40 - 400 l/min 

407 200 3 

1x Adhesive gun ID 17/ 

M 25-40 with shut-off 

valve and E-connector 

for remote control 

408 422 6 

1x Extension cable 20 m 211 506.005 7 

7 

3 

4

Worm pumps 

Sprayboy P 12 

Mixing and pumping in a batch processing operation 

The small mortar pump is ideal for cementitious adhesive, 

fire-retardant plaster, and so on. It mixes, pumps, and sprays 

out of a hopper. It’s just the right machine for building conservationists, 

stucco plasterers, refurbishing companies, 

and painters. 

Suitable for e.g. anti-drumming agents, levelling compounds, 

flame and fire-retardant mortar, sealing slurries, joint and 

frame sealing compounds, paints, adhesive emulsion, cementitious 

adhesive, renovation mortars, filling compounds, and 

mortars. 

Part no. 111 469.060 

Standard cable 

remote control 

Two-stage motor 

speed transfer 

22 

Powerful 

electric motor 

Large material 

hopper

Technical data P 12 

Pump D5 short 

Theor. delivery rate* 6 +12 l/min 

Delivery pressure 25 bar 

Delivery distance** Up to 30 m horizontal, 15 m vertical 

Power connection (CE connector) 400 V / 50 Hz + 60 Hz, 16 A, 5p, 6h 

Pump drive 1.4 kW at 94 rpm / 1.8 kW at 188 rpm 

Hopper volume 50 l 

Weight 125 kg 

Length x width x height 714 x 696 x 1,437 mm 

Fill height 939 mm 

Maximum particle size 4 mm 

Discharge connection M 35 


**The data is based on experience and is dependent on the materials used. 

In the central control cabinet, the electrical 

system is easily accessible at all times – 

which makes maintenance work easier. 

Additional equipment P 12 


 

Cable remote control 

 

Pneumatic remote control 

 

Key: – Not available 

Discharge connection with pressure gauge 

for connection of the mortar hoses. 


23 

The large Sprayboy hopper, in which you mix the material 

before it is pumped. 

Mortar and plaster

Worm pumps 

Suggested accessories for Sprayboy P 12 

Accessories for filling frame connectors with fire-retardant plaster and a filling hose 




2x Mortar hose ID 25, 10 m 207 804.009 1 

1x Frame connector filling hose, 30 cm, M25-40 408 373 2 

3x Seal ID 25 207 764.000 3 


1x Electric remote control 

with on/off switch, 20 m 

269 446.007 5 


1x 

Optional accessory 

PM grout, 18 l storage tank, 25 pcs 266 743.004 

Accessories for processing finishing coats 





1x Air hose, 1/2", 20 m 001 665.004 2 

1x Fine plaster spray gun, large 529 733 3 


3x Seal ID 25 207 764.000 5 

1x V-Meko compressor with fuse 400 168 7 

1x Geka coupling, 1/4" 207 969.009 8 


1x 



24 

3 

2 

2 

5 

3 

8 

1 

5 

4 

1 

4 

7 

5

Accessories for filling frame connectors with fire-retardant plaster and a frame filling device 





3x Seal ID 25 207 764.000 2 

1x Frame connector filling device with remote control 214 236.000 3 

1x Remote control extension cable, 20 m 211 506.005 4 



1x 



Accessories for filling anchor elements 




1x Tapering, V35 / V25-40 207 795.008 1 

3x Seal ID 25 207 764.000 2 

1x Pressure monitor, 2-32 bar 523 102 3 

2x Mortar hose, ID 25-40, 10 m 207 804.009 4 

1x PM coupling, M25-40 / RI 1' 211 597.001 5 

1x Test pressure gauge, ID 25-40 208 745.002 



1x 



25 

5 

3 

5 

4 

2 1 2 

4 

3 

2 6 2 1 

2 

Mortar and plaster

Worm pumps 

Worm pump S 5 

The universal worm pump 

The universal worm pump for dry mix and wet mortar from 

a bag or silo. The S 5 is a modular system. At its heart is a 

powerful worm pump with a slide-on Cardan shaft for the 

quick replacement of the screw parts. It has a variable pump 

output. The TM version has an attached plate mixer for a high 

mix quality. 

Suitable for base and insulating plaster, scraped and textured 

plaster, sprayed and structural plaster, trowel plaster, adhesive 

bridges, masonry mortar, fire-retardant mortar, sealing slurry, 

injection mortar, filling and anchor mortar, dispersion plaster, 

fibre mortar, glass-fibre-reinforced concrete, and cementitious 

adhesives, with an infinitely adjustable feed rate of 

between around 7 and 40 l/min depending on the 

material. 

Part no. 111 635.000 

Suitable worm parts for 

each application can be 

attached 

Slide-on cardan shaft 

makes it easier to change 

the pump parts 

26 

Large hopper with 

capacity of 100 l 

Hinged grille with 

integrated safety switch 

Powerful 

electric vario drive 

Infinitely adjustable 

delivery rate regulation 

Robust metal plate 

protects the motor, 

gearbox, and control 

cabinet

Technical data S 5 EV S 5 EVTM – plate mixer 

Model Basic version with plate mixer 

Worm pump 2L6 2L6 

Delivery rate* 7 - 40 l/min 7 - 40 l/min 


Delivery range** To 60 m To 60 m 

Delivery height** To 40 m To 40 m 

Drive motor 5.5 kW, 400 V / 50 Hz 5.5 kW, 400 V / 50 Hz 

Mixer drive – 2.2 kW 

Mixer volume – 80 l 

Hopper volume 100 l 100 l 

Length 2,290 x 680 x 650 mm 2,505 x 680 x 1,150 mm 

Weight 190 kg 400 kg 

Maximum particle size 6 mm 6 mm 

Pressure connection M 50 M 50 


** The data is based on experience and is dependent on the materials used. 

The S 5 EVTM has an attached plate mixer. It is used if materials need to 

be particularly intensively mixed. 

The plate mixer has a capacity of 80 l and is 

driven by a 2.2 kW electric motor. 

Equipment S 5 EV S 5 EVTM – plate mixer 




 

 

 

Vibrating screen 

– 


27 


The central control cabinet is also a power 

distributor for attached devices such as a plate 

mixer or compressors.

Worm pumps 

Recommended accessories for the S 5 

Accessories for processing site-made mixes 



5 

6 

7 

3 

5 6 

2 7 


1x Pneumatic remote control 465 951 1 


1x Spray gun ID 35 001 306.004 3 

2x Air hose, 1/2", 20 m 001 665.004 4 

1x Nozzle dia. 16 mm 521 643 5 

10x Seal ID 35 213 725.004 6 


10x Seal ID 50 213 266.000 8 

1x Geka coupling, 1/4" 207 969.009 9 

8 

4 

Accessories for processing premixed dry mortar (for cement plaster, fire-retardant plaster, and reinforcement plaster) 



9 3 2 8 

12 

11 10 



2x Mortar hose ID 35, 13.3 m 207 615.007 2 

1x Mortar hose ID 35, V 35 / V 25-40, 5 m 207 808.005 3 

2x Air hose 1/2", 15 m 212 333.002 4 

1x Fine plaster spray gun ID 25 408 237 5 

1x Nozzle dia. 12 mm 521 641 6 

1x Nozzle dia. 14 mm 521 642 7 

5x Seal ID 35 213 725.004 8 

3x Seal ID 25 207 764.000 9 



10x Seal ID 50 213 266.000 12 

1x Geka coupling 1/4" 207 969.009 13 

1x V-Meko compressor with fuse 400 168 14 


28 

6 

8 

4 

9 


1x V-Meko compressor 

with fuse 

400 168 10 


13 

10 

14 

1

Accessories for processing fine plaster (granulation of < 4 mm) 




1x Fine plaster spray gun ID 25 529 733 1 

5x Seal ID 25 207 764.000 2 

1x Tapering, V 35/V 25-40 207 795.008 3 



1x Air hose, 1/2", 20 m 001 665.004 6 

1x Cardan shaft D4 525 378 7 

1x D6 Power rotor 443 740 8 

Accessories for filling anchors 



1 5 


1x Tapering, V 35 / V 25-40 207 795.008 1 

1x Pressure monitor, 2-32 bar 523 101 2 

2x Mortar hose, ID 25, V 25 / M 25, 10 m 207 804.009 3 

5x Seal ID 25 207 764.000 4 

1x PM coupling, M 25-40 / RI 1 211 597.001 5 

1x Test pressure gauge, ID 25-40 208 745.002 

10x Seal ID 50 213 266.000 6 

5 

4 

2 

4 4 

3 1 

6 2 3 12 

29 

11 

6 

10 8.9 7 

2 



1x D6 Power stator 206 345.006 9 

2x Tie rod 011 145.006 10 



1x Pressure connection 202 189.004 12 

In addition, a compressor with an air volume of 

400 - 500 l/min is required. 

4

Worm pumps 

Recommended accessories for the S 5 

Accessories for concrete restoration 



9 

3 

4 

6 

Accessories for spraying glass-fibre reinforced concrete 

8 



3x Mortar hose ID 35, 13.3 m 207 615.007 2 

1x Refurbishing spray gun 207 283.002 3 

1x Coupling V 35 203 135.002 4 

2x Air hose, 20 m 001 665.004 5 

5x Seal ID 35 213 725.004 6 

10x Seal ID 50 213 266.000 7 

1x Adapter, V 50/M 35 213 217.004 


1x Nozzle, dia. 15 mm 207 286.009 9 






1x Fitting block 207 223.004 1 

1x GFB spray gun 070 436.002 2 

1x Hose connection cpl. 209 347.001 3 

1x Mortar hose ID 25, V 35 / V 25 - 40, 10 m 207 809.004 4 

1x Cardan shaft (spiral) 525 378 5 

1x Screw conveyor D 8-2 436 743 6 

1x Screw conveyor barrel D 8-2 436 746 7 

3x Seal ID 35 213 725.004 8 

3x Seal ID 25 207 764.000 9 


2x Tie rod 011 145.006 11 


2 

9 

2 

3 

30 

6 

7 

4 10 12 6.7 

10 

8 

5 

In addition, a compressor with an air volume 

of 1,500 l/min is required. 

11 

5 

8 

1

Modification of pump type 2L6 of S 5 in line with other pump types: 

Conversion of S 5 EV with screwed Cardan shaft to D4, D4½, D4¼, 

D5 short, D6, D8-2+ with the following parts: 

Part Part no. 

1x Cardan shaft (spiral) 202 342.003 

or Cardan shaft (paddle) 206 185.004 

1x Tie rod (l=325 mm, M 20) 011 145.006 

Conversion of S 5 EV 2L6 to D5 with the following parts: 

Part Part no. 

1x Cardan shaft (spiral) 202 342.003 

or Cardan shaft (paddle) 206 185.004 

1x D5 rotor 070 351.006 

1x D5 stator 070 352.005 

1x Clamp, cpl. 206 848.008 

2x Tie rod (l=410 mm, M 20) 467 156 

Part Part no. 

1x 1L6 rotor 207 136.007 

1x 1L6 stator 214 536.001 

1x Clamp, cpl. 422 747 

2x Tie rod (l=300 mm, M 20) 011 145.006 

31 


Conversion of S 5 EV with slide-on Cardan shaft 

(version from part no. 111 452.310, 111 452.330) to D4, 

D4½, D4¼, D5 short, D6, D8-2+ with the following parts: 

Part Part no. 

1x Cardan shaft (spiral) 525 378 

2x Tie rod (l=300 mm, M 20) 011 145.006 

1x Pressure connection 202 189.004 

Conversion of S 5 EV 2L6 to D5 with the following parts: 

Part Part no. 


1x D5 rotor 070 351.006 

1x D5 stator 070 352.005 

1x Clamp, cpl. 206 848.008 

2x Tie rod (l=410 mm, M 20) 467 156 

1x Pressure connection 202 189.004 

Conversion of S 5 EV 2L6 to 1L6 with the following parts: Conversion of S 5 EV 2L6 to 1L6 with the following parts: 

Part Part no. 

1x 1L6 rotor 207 136.007 

1x 1L6 stator 214 536.001 

1x Clamp, cpl. 422 747 

2x Tie rod (l=300 mm, M 20) 011 145.006 

Conversion of S 5 EV 2L6 to 2L54 with the following parts: 

Part Part no. 

1x Rotor 2L54 211 739.005 

1x Stator 2L54 523 235 


For rotors and stators, see page 56 and onwards.

Worm pumps 

SP 11 Beliso Worm pumps 

Convenient plastering machines for premixed dry mortar and site-made mixes 

The models in the SP 11 Beliso worm pumps impress users with 

their sophisticated design and robust and convenient ease of 

use. They have a pivoting, hinged, or hydraulic lifting mixer. 

The machines are suitable for use with site-made mixes or 

ready-to-use interior and external plasters in bags, coloured 

mortars, lime cement plaster, base coat plaster, lightweight 

masonry mortar, ornamental plaster, and filling/grouting work. 

Flap mixer 

* The delivery rate depends on the pump model. Depending 

on the pump used, the delivery rate may be higher or lower. 

** The data is based on experience and is dependent on the 

materials used. 

*** Liquid floor screed version SP 11 BHF is available on request. 

Robust plastic hood 

32 

Infinitely adjustable 

delivery rate 

Swivel mixer 

Lifting mixer for 

convenient filling 

Completely hydraulic pump 

and mixer drive 

PLC 

Stable and 

safe chassis

Technical data*** SP 11 BMR SP 11 BBR SP 11 BMB SP 11 BMT SP 11 BUR 

Model Lifting mixer Lifting mixer Swivel mixer Trap mixer Lifting mixer 

Pump type 2L6 2L6 2L6 2L6 2L6 

Concrete pressure 25 bar 25 bar 25 bar 25 bar 25 bar 

Theor. delivery rate* 5-40 l/min 5-40 l/min 5-40 l/min 5-40 l/min 5-40 l/min 

Delivery range**/ height** 120 m / 60 m 120 m / 60 m 120 m / 60 m 120 m / 60 m 120 m / 60 m 

Compressor 2-cylinder compressor, 400 l/min, 7 bar 

Forced mixer 150 l 150 l 150 l 150 l 150 l 

Conveyor hopper 220 l 220 l 220 l 220 l 220 l 

Drive motor 3-cylinder Kubota, 15 kW*** 4-cylinder Kubota, 

at 2,400 rpm 22.7 kW at 2,600 rpm 

Chassis Unbraked, can be used on roads Braked, can be used on roads 

Drawbar load 60 kg 60 kg 50 kg 50 kg 70 kg 

Weight 750 kg 750 kg 740 kg 730 kg 900 kg 

Length 3,420 mm 3,420 mm 3,510 mm 3,510 mm 3,924 mm 

Width 1,420 mm 1,420 mm 1,420 mm 1,420 mm 1,420 mm 

Height 1,150 mm 1,150 mm 1,240 mm 1,220 mm 1,150 mm 

Filling height 880 mm 880 mm 1,185 mm 1,125 mm 880 mm 

Maximum particle size 6 mm 6 mm 6 mm 6 mm 6 mm 

Part no. 111 505.010 111 505.020 111 505.160 111 505.180 111 505.430 

Powerful worm pump 2L6 with discharge 

connection to hose connection. 

The maximum motor speed of just 2,400 rpm and the good sound 

insulation make the SP 11 into a machine that is quieter than average. 

 

 

 

 

– – – 

– – – 

 

– – – 

– 

– – – 

– – – 

 

 


33 


You can control and programme the complete 

machine from the control panel. 

Equipment SP 11 BMR SP 11 BBR SP 11 BMB SP 11 BMT SP 11 BUR 

Automatic speed regulation 

Manual speed regulation 


Dust extraction 

PLC control 

Electronic water metering 

Mechanical water metering 

Preselection of mixing time 



Radio remote control 


Rubber wiper 

Key: – Not available

Worm pumps 

Suggested accessories for SP 11 Beliso 

Accessories for processing monocouche renders 




1x Mortar hose, ID 35, V50, M 35, 13.3 m 207 616.006 1 

1x Mortar hose, ID 35, V35, M 35, 13.3 m 207 615.007 2 

1x Mortar hose, ID 25, V25, M 25, 5 m 207 808.005 3 

1x Geka air hose, 1/2", 40 m 214 734.007 4 


1x Spray gun, ID 25-40 short 408 237 6 

1x Rubber fine plaster nozzle 8 mm 214 751.006 

1x Rubber fine plaster nozzle 10 mm 214 752.005 

Accessories for processing premixed dry mortar 




2x Mortar hose, ID 50, V 50, M 50, 13.3 m 501 914 1 

1x Mortar hose, ID 35, V 50, M 35, 13.3 m 207 616.006 2 


5x Seal ID 35 213 725.004 4 


Accessories for processing fire-proofing mortar 



6 

8 

8 5 





5x Seal ID 35 213 725.004 4 

5x Seal ID 50 213 266.000 7 

3 2 4 

34 

5 

4 

5 

4 4 3 

6 

2 

2 

4 

1 


1x Rubber fine plaster nozzle 

12 mm 

214 753.004 


14 mm 

214 754.003 


16 mm 

214 755.002 

1x Flexible mortar nozzle, 

D 18 

001 329.007 


1 

3 

1 7 

7 



5x Seal ID 50 213 266.000 7 

1x Spray gun, V 35 203 054.002 8 




1x Spray gun, V 35 203 054.002 8 

3x Hose holder, leather 000 206.008

Accessories for processing site-made mixes 







5x Seal ID 35 213 725.004 4 


5x Seal ID 50 213 266.000 6 

Accessories for injection and pressure grouting 





5x Seal ID 50 213 266.000 2 




8 

2 

4 

4 

35 

5 

2 

1 

3 

5 7 

6 

3 

1 2 

4 




1x Base coat plaster spray 

gun, short, V 35 

001 306.004 8 



1x Injection nozzle with 

T-piece, pressure gauge, 

remote control air cock, 

coupling with spout 

ID 50, expanding collar 

D 45, and collar D 38 

001 128.004 5

Application overview for piston pumps 

Machines for pumping fine concrete 

and self-levelling floor screed 

For small or large construction sites, for fine or coarse materials, 

for short or long delivery distances: Putzmeister machines are powerful 

and really make work easier. 


with machine technology. In you have any questions, please contact 

the material manufacturer or contact us directly. 

36 

 

Very 

suitable 

Piston pumps 

P 13 

Pages 38 - 39 

Piston pumps 

P 715 

Pages 42 - 43 

Piston pumps 

P 718 

Pages 48 - 49 

Suitable 


– 

Not 

suitable

Fine concrete, 

granulation 

of up to ~ 8 mm 

– – 

– – 

37 

Fine concrete, self levelling floor screed 

Fine concrete Self-levelling floor screed 


granulation 



granulation 


Shotcrete, 

granulation 


Ready-mix mortar, 

granulation 


Site-made mix, 

granulation 


–

Piston pumps 

P 13 piston pump 

The robust machine for really difficult mixes and all pumpable sands to 10 mm 

The robust P 13 is suitable for really difficult site-made mixes 

and almost any type of pumpable sand. It is extremely low-wear 

and completely reliable. 

Above all, this machine is intended for construction sites 

where really harsh conditions prevail. A deliberate decision 

was therefore taken to avoid electronic components. All 

functions and operating elements of the P 13 are purely 

mechanical and therefore particularly robust and insusceptible 

to malfunction. 

It is suitable for site-made mixes or bagged interior 

and external plasters, bentonite limes, coloured mortar, 

cement plaster, lime cement plaster, fine shotcrete 

material, masonry mortar, self levelling floor 

screed, and grouting work (in all cases, the 

mix must be homogenous). 

With the extremely resistant type KA 230 pump, it can also 

process practically any sand up to a granulation of 10 mm: 

crushed sand, dune sand, washed river and sea sand, desert 

sand, and much more. 

Part no. 111 632.000 

Robust and powerful piston pump 

(in this case, KA 230) 

38 

Positive mixer with 

volume of 170 l 

Integrated compressor 

Robust metal hood protects 

the motor, compressor, and 

gearbox 

Output can be regulated 

(3 stages)

Technical data P 13 DMR – KA 139 P 13 DMR – KA 230 P 13 EMR – KA 139 P 13 EMR – KA 230 

Mechanical piston pump KA 139 KA 230 KA 139 KA 230 

Theor. delivery rate 20 - 80 l/min 30 - 90 l/min 20 - 80 l/min 30 - 90 l/min 

Concrete pressure 40 bar 40 bar 40 bar 40 bar 

Piston stroke 130 mm 130 mm 130 mm 130 mm 

Piston diameter 100 mm 100 mm 100 mm 100 mm 

Max. delivery distance* 300 m horizontal, 100 m vertical 

Air compressor 2-cylinder compressor, 3.5 bar, 300 l/min 

Hopper volume 200 l 200 l 200 l 200 l 

Mixer volume 170 l 170 l 170 l 170 l 

Drive motor 2-cylinder diesel motor 2-cylinder diesel motor 400 V electric motor 400 V electric motor 

12.5 kW at 2,800 rpm 12.5 kW at 2,800 rpm 7.5 kW at 2,900 rpm 7.5 kW at 2,900 rpm 

Chassis Unbraked Unbraked Unbraked Unbraked 

Fuse – – 20 A 20 A 

Weight 990 kg 990 kg 990 kg 990 kg 

Length x width x height 3,000 x 1,640 x 1,450 mm 3,000 x 1,640 x 1,450 mm 3,000 x 1,640 x 1,450 mm 3,000 x 1,640 x 1,450 mm 

Filling height 1,300 mm 1,300 mm 1,300 mm 1,300 mm 

Max. particle size 6 mm 10 mm 6 mm 10 mm 

Pressure connection M 50 M 50 M 50 M 50 


The large forced mixer ensures top 

mix quality. 


unbraked 

braked 


The powerful 2-cylinder diesel motor works in a relatively low speed range 

and is extremely robust and requires low maintenance. 

Equipment P 13 DMR – KA 139 P 13 DMR – KA 230 P 13 EMR – KA 139 P 13 EMR – KA 230 

 

 

 

 


 


39 

Mortar, fine concrete, self levelling floor screed 

The pressure connection of piston pump KA 230 

in the P 13 for the hose connection

Piston pumps 

Suggested accessories P 13 

Standard mortar line for spray plastering 




2x Mortar hose, 13.3 m, ID 50, V 50 / M 50 501 914 1 

1x Mortar hose, 13.3 m, ID 50, M 35 / V 50 207 616.006 2 

1x Air hose 40 m, 1/2 " 214 734.007 3 

5x Seal ID 35 213 725.004 4 

5x Seal ID 50 213 266.000 5 




1x 



Accessories for injection 




5x Seal ring ID 50 213 266.000 1 



2x Air hose 40 m, 1/2 " 214 734.007 4 

1x Injection nozzle, cpl., with T-piece, 

pressure gauge, remote control air cock, 

coupling with spout ID 50, 

mounted expanding collar D 45, 

and collar D 38 

001 128.004 5 


1x 



5 

40 

4 

2 5 1 5 5 

1 

3 

3 

4 

1 1 2 

6 7

Accessories for shotcreting, max. 40 bar, ≤ 8 mm granulation 



An additional site compressor is required. 


5x Seal ring ID 50 213 266.000 1 



1x Air hose 20 m, 3⁄4" 416 015 4 

1x Air hose, 1/2", 40 m 214 734.007 5 

1x Ball valve, 11/2" 207 792.001 6 

1x Concrete spray gun, V 50, 30 mm 072 157.004 7 

2x Geka coupling, 1/2" AG 014 068.009 8 



1x PM cement slurry powder, 18 l storage tank, 

25 pcs 

7 

266 743.004 

8 

6 

1 

41 

8 


5 

3 

1 

7 

1 

2

Piston pumps 


The compact trailer piston pump for a granulation of up to 16 mm 

The small, light, and efficient trailer fine concrete pump for 

pumping anhydrite, cement and cementrite, self levelling floor 

screed, 

and fine concrete with a granulation of up to 16 mm is also 

ideal for shotcreting and mortar grouting. 

The S transfer tube with self-seal effect allows up to 68 bar 

pump pressure and is even sealed for sludge and water. 

The self-adjusting ring on the S transfer tube automatically 

compensates for wear. 

Part no. 111 631.000 

Light and robust 

plastic hood 

Double piston pumps 

with hard chrome-plated 

cylinders 

Various hood colours 

(optional) 

Roadworthy 

T-chassis 

Support foot to 

ensure stability 

42 

Cover protects instruments 

and switches 

Deep agitator to ensure 

homogenous mixing 

Large concrete hopper with 

agitator and rubber collar 

Safety grille with 

optional vibrator 

Pump and S-transfer tube are 

hydraulically controlled

Technical data P 715 TD P 715 SD P 715 TE P 715 SE 

Machine type Trailer pump Stationary pump Trailer pump Stationary pump 

Pump 2-cylinder piston pump, hydraulically driven 

Theoretical delivery rate (ground) 4 - 17.4 m 3 /h 4 - 17.4 m 3 /h 4 - 18.2 m 3 /h 4 - 18.2 m 3 /h 

Delivery pressure (ground) 68 bar 68 bar 68 bar 68 bar 

Cylinder diameter 150 mm 150 mm 150 mm 150 mm 

Length of piston stroke 700 mm 700 mm 700 mm 700 mm 

Strokes per min. 27 27 27 27 

Drive cylinder diameter 80 / 45 mm 80 / 45 mm 80 / 45 mm 80 / 45 mm 

Drive motor 3-cyl. diesel motor, Deutz D L03 2011, 34.5 kW 30 kW electric motor, 400 V, 50 Hz 

Hopper capacity 250 l / 280 l (with rubber collar) 

Chassis T-chassis, 1,900 kg Skid frame T-chassis, 1,900 kg Skid frame 

Weight 1,850 kg 1,700 kg 1,800 kg 1,650 kg 


Filling height 1,180 mm 973 mm 1,180 mm 973 mm 


Operation is easy. Everything is well laid out 

and easy to reach. 

Equipment P 715 TD P 715 SD P 715 TE P 715 SE 



Rubber collar 

Lifting eye 


Flushing water pump 


Working light 


Exhaust flap 




Air vessel (self levelling screed) 

Vibrator 

Simply fold the hopper away to the side. The 

agitator is already open and easily accessible 

in front of you. 

 

 

 

– – 

 

 

 

 

– – 

– – 

 

 

– – 

 

 

Grille 

 


43 


You can reach all areas for maintenance and 

servicing easily, to enable you to check the oil 

level, for example. 


the hood in the RAL 

colour of your choice.

Piston pumps 

Accessories sets for the P 715 

Delivery line for fine concrete, mortar, and self levelling floor screed, SK 50, 60 bar, ≤ 8 mm granulation 


Standard delivery line ≈ 100 m long, consisting of: 


4x Clamp coupling SK 4.5" 431 613 1 

4x Gasket ID 100, 4.5" 057 341.000 2 

55x Securing cotter pin 018 878.004 3 

1x Delivery line bend SK 100, 4.5", 90° 421 329 4 

1x T-delivery pipe SK 100, 4.5", 1,000 mm 057 614.009 5 

1x Pressure gauge SK 100, 4.5", 100 bar 521 430 6 

1x Reducer pipe 100, 50-4.5"/3", 1,500 mm 238 508.002 7 

45x Clamp coupling SK, 3" 417 798 8 

55x Gasket ID 65, 3" 064 084.004 9 

4x Delivery bend pipe SK 50, 3", 90° 081 777.006 10 

2x Delivery pipe SK 50, 3", 1,000 mm 081 783.003 11 



4x Delivery line bend SK 50, 3", 45° 081 779.004 14 

1x Delivery hose 3", SK 50, 3", 2,000 mm 481 169 15 

6x Sponge ball, diameter of 60 mm 000 212.005 16 

44 

1,2,3 

1,2,3 

5 

5 

4 

4 

1,2,3 

1,2,3 

8,9,3 

8,9,3 

10 

10 

1,2,3 

1,2,3 

1,2,3 

1,2,3 

7 

7 

6 

6 

11,12,13 

8,9,3 

8,9,3 

Delivery line for fine concrete, mortar, and self levelling floor screed, SK 65, 85 bar, ≤ 12 mm granulation 





4x Gasket ID 100, 4.5" 057 341.000 2 





1x Reducer pipe 100, 65-4.5"/3", 1,000 mm 224 269.009 7 

44x Clamp coupling SK 3" 417 798 8 

44x Gasket ID 65, 3" 064 084.004 9 






1x Delivery hose SK 65, 3", 5,000 mm 535 521 15 


11,12,13 

8,9,3 

8,9,3 

8,9,3 

14 

8,9,3 

14 

8,9,3 

11,12,13 

8,9,3 

11,12,13 

15 

15 

16 

16

Delivery line for mortar and self levelling floor screed, PM 50, 40 bar, ≤ 8 mm granulation 





5x Gasket ID 100, 4.5" 057 341.000 2 



1x T-delivery pipe SK 100, 4.5", 1 m 057 614.009 5 


1x Reducer pipe SK 100, 4.5"- SK 65, 3", 1.5 m 238 508.002 7 


1x Gasket ID 65, 3" 064 084.004 9 

1x Transition piece SK 50/ RA 2" 082 784.001 10 

1x PM coupling V 50, RI 2" 205 273.001 11 

6x Mortar hose ID 50, 40 bar, 13.3 m 501 914 12 




45 

1,2,3 


Flexible delivery line for fine concrete, mortar, and self levelling floor screed, ID 100 / 4.5", 85 bar, ≤ 16 mm granulation 



22x Gasket ID 100, 4.5" 057 341.000 2 


2x Delivery line bend SK 100, 90°, 4.5" 421 329 4 



18x Delivery hose SK 100, 4.5", 2,850 mm 253 319.001 11 


1,2,3 

5 

1,2,3 

4 

4 

1,2,3 

1,2,3 

1,2,3 

5 

1,2,3 

6 

4 

11 

1,2,3 

1,2,3 

1,2,3 

4 

7 

6 

8,9,3 

10 

11 

11 

12 

1,2,3 

12 

1,2,3 

13 

11 

11

Piston pumps 

Accessories sets for the P 715 

High-pressure concrete spraying line, SK 65 / SK 50, 3", max. 85 bar, ≤ 10 mm granulation 


Standard delivery line, ≈ 60 m long, consisting of: 

17 

17 18 

1,2,3 

1,2,3 

1,2,3 

1,2,3 

18 

5 

4 

4 

16 

1,2,3 

1,2,3 

6 

15 

7 

8,9,3 10 

8,9,3 8,9,3 8,9,3 

11 

12 

19 

19 

17 



4x Gasket ID 100, 4.5" 057 341.000 2 





1x Reducer pipe SK 100, 4.5"- SK 65 / 3", 1 m 224 269.009 7 


16x Gasket ID 65, 3" 064 084.004 9 


1x Reducer pipe SK 65, 3" - SK 50, 3", 1,000 mm 058 670.000 11 


1x Transition piece SK 50, 3" to 2", IG 082 784.001 13 

1x High-pressure concrete spray gun 

with rubber nozzle, 2", AG 

532 589 14 



2x Air hose, 3⁄4", 20 m 416 015 17 

1x Replacement rubber nozzle 532 590 

1x Geka 3 ⁄8" RA 041 403.006 20 

46 

20 

13 

Metering pump for accelerator Part no. Fig. 

1x Air hose 3⁄4", 20 m 416 015 17 

1x Silicate metering pump with compressed 

air drive (barrel pump) with connection coupling 

002 423.009 18 

2x High-pressure hose 1/2", 20 m 001 983.003 19 

14

1,2,3 

1,2,3 

5 

1,2,3 

Concrete spraying line, SK 65 / PM 50 / 3"; max. 40 bar, ≤ 8 mm granulation 



4 

4 

16 19 

1,2,3 

1,2,3 

1,2,3 

5 

1,2,3 

6 

4 

4 

1,2,3 7,8,9 1,2,3 

1,2,3 

1,2,3 

10 

18 

6 

16 

17 

7 

1,2,3 

7,8,9 

8,9,3 

1,2,3 

11 

20 

12 

10 

Delivery line for fine concrete, mortar, and self levelling floor screed, SK 100 / 4.5", 85 bar, ≤ 16 mm granulation 



8,9,3 

11 

47 

8,9,3 




4x Gasket ID 100, 4.5" 057 341.000 2 



1x T-delivery pipe SK 100, 4.5", 1 m 057 614.009 5 


1x Reducer pipe SK 100, 4.5"-SK 65, 3", 1 m 224 269.009 7 


15x Gasket ID 65, 3" 064 084.004 9 

8x Delivery hose SK 65, 3", 5 m 535 521 10 

1x Reducer pipe SK 65, 3"-SK 50, 3", 1,000 mm 058 670.000 11 

1x Transition piece 082 784.001 12 

1x PM coupling M 50, 2" 211 600.008 13 

1x Mortar hose ID 50 TS PN 40, 13 m 501 914 14 

1x Concrete injection nozzle V 50, 30 mm 072 157.004 15 

2x Air hose 3⁄4", 20 m 416 015 16 



12 

13 

14 

Metering pump for accelerator Part no. Fig. 

1x Air hose 3⁄4", 20 m 416 015 16 

1x Silicate metering pump with compressed 

air drive (barrel pump) with connection coupling 

002 423.009 19 

2x High-pressure hose 1/2", 20 m 001 983.003 20 



55x Gasket ID 100, 4.5" 057 341.000 2 





30x Delivery pipe SK 100, 4.5", 3,000 mm 056 863.000 7 



4x Delivery line bend SK 100, 4.5", 45° 057 593.007 10 



15

Piston pumps 


Compact trailer fine concrete pump for a granulation of up to 32 mm 

The P 718 offers all of the advantages of its little sister the P 715 

and in addition to its traditional use for fine concrete and selflevelling 

floor screed, it is also ideal for pumping fine concrete 

up to 32 mm granulation. 

Part no. 111 631.000 

Light and robust 

plastic hood 

Double piston pumps with 

hard chrome-plated cylinders 

Selectable hood colour 

(optional) 

Roadworthy 

T-chassis 

48 

Cover protects 

instruments and switches 

Standard lifting eye 

Support foot to 

ensure stability 

Large concrete hopper with 

agitator and rubber collar 

Safety grille with 

optional vibrator 

Pump and S-transfer tube 

are hydraulically controlled 

Hopper easily folded away 

for maintenance or cleaning

All operating elements are arranged clearly 

on one side. This means that everything can 

be reached easily and operated simply. 

The deep agitator ensures homogenous mixing 

and is easily accessible since the hopper can be 

folded out of the way. 

 

 

 

 

 

 

 

 

– – 

– – 

 

 

– – 

 

Grille 

 


49 


Technical data P 718 TD P 718 SD P 718 TE P 718 SE 

Machine type Trailer pump Stationary pump Trailer pump Stationary pump 

Pump 2-cylinder piston pump, hydraulically driven 

Length of piston stroke 700 mm 700 mm 700 mm 700 mm 

Strokes per min. 25 25 25 25 

Drive cylinder diameter 80 / 45 mm 80 / 45 mm 80 / 45 mm 80 / 45 mm 

Theoretical delivery rate (ground) 17.4 m 3 /h 17.4 m 3 /h 17.4 m 3 /h 17.4 m 3 /h 

Delivery pressure (ground) 70 bar 70 bar 70 bar 70 bar 

Cylinder diameter 150 mm 150 mm 150 mm 150 mm 

Drive motor 3-cyl. diesel motor, 34.5 kW 30 kW electric motor, 400 V, 50 Hz 

Hopper capacity 360 l 360 l 360 l 360 l 

Chassis T-chassis Skid frame T-chassis Skid frame 

Weight 2,320 kg 2,000 kg 2,260 kg 1,940 kg 


Filling height 1,180 mm 1,120 mm 1,180 mm 1,120 mm 


Thanks to the wide-opening hood, all 

areas of the motor can be easily reached 

for maintenance and service. 

Equipment P 718 TD P 718 SD P 718 TE P 718 SE 



Rubber collar 

Lifting eye 


Flushing water pump 


Working light 


Exhaust flap 




Vibrator 


the hood in the RAL colour 

of your choice.

Piston pumps 

Suggested accessories P 718 






60x Gasket 5.5" 055 559.001 2 


6x Delivery line bend SK 125, 5.5" 90° r=275, 

high-pressure 

261 402.007 4 

1x T-delivery pipe SK 125, 5.5" 1,000 mm 057 615.008 5 

1x Pressure gauge SK 125, 5.5" 100 bar 521 448 6 






4x Delivery hose SK 125, 5.5", 3,000 mm 433 497 11 

6x Sponge ball ID 150, medium design 018 841.002 12 

6x Sponge ball ID 150, hard 223 673.007 12 

1x Support holder for end hose 054 371.002 12 

50 

1,2,3 

5 

1,2,3 

1,2,3 

4 

1,2,3 

1,2,3 

5 

1,2,3 

4 11 

4 

4 

1,2,3 

1,2,3 

6 

1,2,3 

1,2,3 

7,8,9 

6 

7 

1,2,3 

10 

1,2,3 

8,9,3 8,9,3 

10,11,12 

7,8,9 

13 

1,2,3 

Additional accessories: Part no. Fig. 

1x Manual gate valve, 

GVM 2/2, 130 bar 

413 087 

1x Wash-out port lid, 

SK 125, 5.5" 

057 619.004 

1x PM grout, 18 l storage tank, 

25 pcs 

266 743.004 

1x Pipeline mount, 

wall and ground 

051 038.005 13 






6x Gasket 5.5" 055 559.001 2 


2x Delivery line bend SK 5.5" 90° 261 402.007 4 

1x T-delivery pipe SK 125, 5.5"; 1,000 mm 057 615.008 5 


1x Reducer pipe SK 125, 5.5", 

SK 100, 4.5", 1,000 mm 

057 604.006 7 

50x Clamp coupling, SK 4.5" 431 613 8 

50x Gasket ID 100, 4.5" 057 341.000 9 






6x End hose SK 100, 4.5", 2,850 mm 253 319.001 14 

6x Sponge ball ID 120, diameter of 100 mm 016 091.003 15 

13 

8,9,3 

12 

10,11,12 

16 

14 

8,9,3 


1x Wash-out port lid for 

T-delivery pipe, 5.5" 

057 628.008 

1x Pipeline mount, 

wall or ground 

051 038.005 16 


25 pcs 

266 743.004 

15


Standard hose line ≈ 100 m long, consisting of: 

1,2,3 

1,2,3 

5 

1,2,3 

4 

51 

4 


Flexible delivery line for fine concrete, mortar, and self levelling floor screed, SK 125 / 5.5", 85 bar, ≤ 32 mm granulation 



60x Gasket 5.5" 055 559.001 2 


4x Delivery line bend SK 125, 5.5" 90° 261 402.007 4 





6x Sponge ball ID 150, medium design 018 841.002 12 

6x Sponge ball ID 150, hard 223 673.007 12 

3x End hose SK 125, 5.5", 3,000 mm 233 649.005 13 

1x Support holder for end hose 054 371.002 

1,2,3 

5 

1,2,3 6 

1,2,3 

1,2,3 

4 

1,2,3 

4 

1,2,3 

1,2,3 

11 

6 

1,2,3 

7 

8,9,3 

12 

1,2,3 

11 1,2,3 

11 



25 pcs 

266 743.004 

1x Wash-out port lid for 

T-delivery pipe, 5.5" 

057 628.008 

1x Delivery hose SK 125, 5.5", 

3,000 mm 

433 497 11 

1x Delivery hose SK 125, 5.5", 

4,000 mm 

089 983.009 11 

1x PM hose carriage, cpl. 482 464 

Flexible delivery line for fine concrete, mortar, and self levelling floor screed, SK 100 / 4.5", 85 bar, ≤ 16 mm granulation 





6x Gasket 5.5" 055 559.001 2 


2x Delivery line bend SK 125, 90°, 5.5" 261 402.007 4 

1x T-delivery pipe SK 125, 5.5" 1,000 mm 057 615.008 5 


1x Reducer pipe SK 125, 5.5", 

SK 100, 4.5", 1,000 mm 

057 604.006 7 

50x Clamp coupling SK 100, 4.5" 431 613 8 

50x Gasket ID 100 4.5" 057 341.000 9 


6x Sponge ball ID 120, diameter of 100 mm 016 091.003 11 


1x Wash-out port lid for T-delivery pipe, 5.5" 057 628.008 

1x PM grout, 18 l storage tank, 25 pcs 266 743.004 

10 

8,9,3 

10 

8,9,3 

Alternative: Part no. Fig. 

1x Delivery hose SK 100, 

4.5", 5,000 mm 

057 609.001 10 

11 

8,9,3 

13 

10 

10

Accessories for pneumatic conveyors 

Accessories 

Screed smoothing machine EB 600l 

With 230 V, 50 Hz electric geared motor, 

1.1 kW, 120 kpm, 

smoothing disc with diameter of 600 mm, 

height-adjustable guide frame, 

cpl. with CEE standard coupling 16 A, 

gross weight of 42 kg 

Screed smoothing plate 

D 600, light, 

for smoothing machine EB 600 L 

Delivery hose Mixokret ID 50 

incl. couplings 

40 bar, 50 x 9 mm, length of 13.3 m 

Part no. 

501 914 

40 bar, 50 x 9 mm, length of 20 m 501 915 

Individual items for retrofitting* 

Coupling V 50 / S 50 206 604.006 

Coupling M 50 / S 50 211 595.003 

ID 50, hose, 40 bar, bulk stock, 

50 x 9 mm 

501 913 


50 x 8 mm 

213 449.005 

4x hose clamp D 68 B 250 E 001 046.005 

Gasket for coupling 213 266.000 

Delivery hose Mixokret ID 65, KK 70, 


10 bar, 65 x 10 mm, length of 10 m 

Part no. 

456 831 



Coupling KKV 70 / S 65 211 352.000 

Coupling KKM 70 / S 65 211 351.001 


65 x 10 mm 

001 685.000 

4x hose clamp D 88, 9 B 19 015 288.008 


* Does not correspond to original/only for repair 

Part no. 

H 180 170 0051 

Part no. 

H 280 974 1847 

52 

You can search for and identify the 

spare parts you need using our 

electronic spare parts catalogue. For 

more information, see our home page at 


(Services -> Accessories and spare parts management). 




Part no. 

443 675 


Individual items for retrofitting 

(integrated externally)* 

Coupling KKV 89 / HR 65 213 734.008 

Coupling KKM 89 / HR 65 213 735.007 

Hose, 10 bar, bulk stock, 65 x 10 mm 001 685.000 

8x washer A 8.4 037 107.002 

8x round head screw M 8 x 25 043 198.005 

8x hexagon nut M 8 034 105.007 

8x washer 13 037 107.002 




Part no. 



Coupling KKV 89 / 90 S 455 303 

Coupling KKM 89 / 90 S 455 316 

Hose, 10 bar, 90 x 11.5 mm, 10 m 454 408 

4x hose clamp D 101 - 110 B 20 016 337.000 




Top quality 

Original parts 


Mörtelmaschinen 

Part no. 



Coupling KKV 108 453 503 

Coupling KKM 108 453 504 

Hose, 10 bar, 90 x 11.5 mm, 10 m, without coupling 454 408 

4x hose clamp D 127 B 19, 1-piece 016 337.000 

Gasket for O-ring coupling, 124 x 18, NBR 55-60 210 580.006

Putzmeister couplings for Mixokret hoses 

with ID 50, ID 65, and ID 70 mm 

Coupling ID Part no. 

KKM 70 / RI 21 ⁄2" 015 664.004 

M 65 / S 65 402 274 

V 65 / S 65 402 289 

M 65 / RI 21 ⁄2" 402 288 

V 65 / RI 21 ⁄2" 402 290 

M 50 / S 50 211 595.003 

V 50 / S 50 206 604.006 

M 50 RI 2" 211 600.008 

Cardan joint couplings for Mixokret hoses 

with ID 50-90 mm 

Coupling ID Part no. 

KKM 70 HR 50 213 736.006 

KKV 70 HR 50 213 737.005 

KKM 70 / 60 S 071 946.009 

KKV 70 / 60 S H 717 160 0000 

KKM 70 / 65 S 211 351.001 

KKV 70 / 65 S 211 352.000 

KKM 89 HR 65 213 735.007 

KKV 89 HR 65 213 734.008 

KKM 89 / 90 S 065 109.001 

KKV 89 / 90 S 065 108.002 

KKM 70-R 21 ⁄2" 015 664.004 

KKV 70-R 21 ⁄2" 015 197.005 

KKM 89-R 21 ⁄2" 014 895.007 

KKV 89-R 21 ⁄2" 209 205.004 

KKM 89-R 3" 209 325.007 

KKV 89-R 3" 073 443.005 

KKM 70 / V 50 reducer coupling 071 790.006 

KKV 89, ID 65 mm 455 902 

KKM 89, ID 65 mm 455 904 

KKV 108, 90 S 453 503 

KKM 108, 90 S 453 504 

M = female 

V = male 

S = spout 

HR = integrated externally 

53 

Discharge stands 


Part no. 

Discharge stand, 3 legs 

Steel, ID 50 529 740 

Steel, KK 70 529 741 

Steel, KK 89 529 742 

Aluminium, ID 50 529 743 

Aluminium, KK 70 529 744 


Rubber foot 435 226 

Discharge stand, with runner 

Steel, ID 50 529 746 

Steel, KK 70 529 747 

Steel, KK 89 529 748 

Aluminium, ID 50 529 749 



Discharge stand, 3 legs incl. adapter 

KK 70 KK 89, foot can be removed 

517 367 

Discharge stand, KKM 108 209 811.003 

Wear and spare parts for discharge stands 

Adapter for discharge stand ID 50 

Part no. 

458 782 

Adapter for discharge stand KK 70 458 783 

Adapter for discharge stand KK 89 496 531 

Locking peg for discharge stand adapter 499 202 

Rubber pot for discharge stand 468 004 

Rubber foot 435 226


3 

Wear plates for Mixokret M 740 and M 760 

Quantity* Designation Fig. Part no. 

Wear-resistant standard plates: 

1x With cut-out 1 429 862 

2x Front/rear 2 429 864 

2x Top side 3 429 865 

Highly wear-resistant plates: 

1x With cut-out (6 mm) 1 212 322.000 

2x Front/rear (6 mm) 2 212 321.001 

2x Top side (6 mm) 3 212 323.009 

Plastic wear plates (red) 

1x With cut-out 1 484 310 

2x Front/rear (6 mm) 2 484 311 

2x Top side (6 mm) 3 484 312 

Steel plates for bumped boiler ends (4 mm) 

2x Front wear plate I 4 430 139 

2x Front wear plate II 5 430 140 

Set of wear plates, M 740, M 760 

incl. screws, domed nuts, and sealing rings: 

1x Set of standard wear plates 524 537 

1x Set of highly wear-resistant plates 214 307.007 

1x Set of plastic wear plates 492 658 

Wear plates for Mixokret M 730 

Quantity* Designation Part no. 

1x Wear plate I 430 208 

1x Wear plate II 430 209 

* Per tank 

3 

1 

2 

3 

54 

2 1 2 

4 5 

1 3 

Mixing paddle for Mixokret 

4 

Designation Fig. Part no. 

Front mixer plate 1 205 305.005 

Front mixer plate for Mixokret 

M 730 

1 207 885.002 

Central mixer plate, 2 pcs 2 205 306.004 

Central mixer plate, 2 pcs, 

for Mixokret M 730 

2 207 886.001 

Rear mixer plate 3 205 237.005 

Rear mixer plate for Mixokret 

M 730 

3 207 887.000 

M 760, M 740, M 730: 

Mixer plate holder, 2 pcs, rear 4 205 514.003 

Mixer plate holder, 2 pcs, front 4 205 513.004 

Mixing paddle set for Mixokret 

M 3000 and from M 700, 

complete, in plastic bucket with 

fastening screws 

2 

3 

5 

5 206 581.006

Smoothing beams and measuring sticks, model SLN 

With 1 horizontal spirit level, dimensions: approx. 80 x 17 mm 

Measuring precision: 1 mm/m = 0.057° in normal position 

100 cm 

Part no. 

362 315.006 

150 cm 362 316.005 

200 cm 362 317.004 

250 cm 362 318.003 

300 cm 362 319.002 

Knee protectors 

1 pair of floor screed overshoes 

For work on fresh floor screed 

Part no. 

557 968 

Front belt 362 771.000 

Rear belt 362 772.000 

Part no. 

Harmonica 362 344.006 

Box-form made from polyurethane, CFC-free production, 

362 343.007 

certified as per DIN EN 14404 

55 

Levelling stands 

With high feet for larger floor screed heights 

Part no. 

Standard: 12 cm 211 703.002 

High: 14 cm 211 704.001 

Service packages 

M 740 


500 hour service 

Consisting of: gaskets, oil filter, fuel filter, 

filter insert for air filter, spin-on filter 


Consisting of: gaskets, oil filter, fuel filter, 

filter insert for air filter, spin-on filter, 

V-belts, service kit oil trap 

M 760 


Consisting of gaskets, oil filter, fuel filter, 

spin-on filter, Micro-Top cartridges 


Consisting of: gaskets, oil filter, fuel 

filter, spin-on filter, Micro-Top cartridges, 

V-belts, service kit oil separator 

Part no. 

493 689 

504 208 

502 366 

504 207

Accessories for plastering machines 

Rotors and stators 

Rule of thumb: 

The finer the granulation and the softer the material to be pumped, 

the harder the required rubber quality for the screw conveyor barrel. 

The grainier the material and the harder the aggregate, the softer the 

required rubber quality. 

Mixer pump MP 25 MIXIT 

Type Delivery rate 

(l/min) 

l/min at 100 rpm** 

(75% efficiency) 

56 

Colour Hardness 

(˚Shore) 

Max. 

granulation 

(mm) 

Pump 

pressure 

(bar) 

d 1 

d 2 

Length/ 

diameter of 

stator (mm) 

D4 1/4 6 2.5 white 70 3 40 270 / 90 

D4 1/4 6 2.5 black 65 3 30 270 / 90 

D4 1/2 12 4.5 green 70 3 40 270 / 90 

D4 1/2 12 4.5 black 65 3 30 270 / 90 

D4 20 5.5 red 72 4 20 270 / 90 

D4 20 5.5 yellow 50 4 20 270 / 90 

D5 short 40 7.8 brown 72 4 20 270 / 90 

D6 Twin 25 6.5 white 73 4 40 270 / 90 

D6 Power 25 6.5 red 73 4 40 270 / 90 

D6-3 25 6.5 orange 73 4 40 270 / 90 

D6-3 25 6.5 blue 73 4 40 270 / 90 

D6-3 Action 25 6.5 orange 73 4 40 270 / 90 

D7-2 35 9 red 73 4 40 270 / 90 

D8-2 40 8.8 black 65 4 30 270 / 90 

Assembly aid for rotor/stator 

Sprayboy P 12 worm pump 


(l/min) 

Part no. 

Silicone spray, 400 ml spray can 508 975 



D 4 Yellow 


(˚Shore) 

Slope s (mm) 

Stator length l 1 (mm) 

Rotor length l 2 (mm) 

Max. 

granulation 

(mm) 

D 6 Power 

Pump 

pressure 

(bar) 

Length/ 

diameter of 

stator (mm) 

D4 1/4 1.5 + 3 2.5 white 70 3 40 270 / 90 

D4 1/4 1.5 + 3 2.5 black 65 3 30 270 / 90 

D4 1/2 2.5 + 5 4.5 green 70 3 40 270 / 90 

D4 1/2 2.5 + 5 4.5 black 65 3 30 270 / 90 

D4 3.5 + 7.5 5.5 red 72 4 20 270 / 90 

D4 3.5 + 7.5 5.5 yellow 50 4 20 270 / 90 

D5 short 6 + 12 7.8 brown 72 4 20 270 / 90 

Diameter

Length of rotor 

without pin (mm) 

Rotor head model Stator 

part no. 

Rotor 

part no. 

57 

Clamping jacket 

part no. 

320 Groove 214 573.006 214 572.007 Maintenance-free 400 912 

320 Groove 402 321 214 572.007 208 129.000 400 912 

320 Groove 214 403.008 214 402.009 Maintenance-free 400 913 

320 Groove 403 523 214 402.009 208 129.000 400 913 

320 Groove 010 316.001 207 140.006 208 128.001 – 

320 Groove 010 313.004 207 140.006 208 128.001 – 

320 Groove 071 011.002 071 234 009 208 128.001 400 910 

320 Groove 406 978 443 740 Maintenance-free 400 911 

320 Groove 206 345.006 443 740 Maintenance-free 400 911 


320 Groove 492 020 473 638 208 129.000 487 115 


320 Groove 485 478 485 479 Maintenance-free – 




BORE GROOVE 

GROOVE/BORE SLOT 


part no. 

D 4 1/2 D 4 1/4 

Rotor 

part no. 


part no. 

320 Groove 214 573.006 214 572.007 Maintenance-free 

320 Groove 402 321 214 572.007 208 129.000 


320 Groove 403 523 214 402.009 208 129.000 

320 Groove 010 316.001 207 140.006 208 128.001 

320 Groove 010 313.004 207 140.006 208 128.001 

320 Groove 071 011.002 071 234 009 208 128.001 


D 5 Short 

Rotor for unimixer 

part no. 

D 6-3 D 6-3 Action D 6 Twin D 6-3 Blue 

= series equipment 

* Needs conversion 

** Depending on material, 

consistence, delivery range, 

and pressure 

*** Stainless steel, 

hard chrome-plated


Worm pump S 5 (with screwed-on Cardan shaft) 


(l/min) 



58 


(˚Shore) 

Max. 

granulation 

(mm) 

Pump 

pressure 

(bar) 

Length/ 

diameter 

stator (mm) 

2L6 7 - 40 17 yellow 73 6 40 540 / 100 

D6 Power* 3 - 18 6.5 red 73 4 40 270 / 90 

D8-2* 4 - 23 8.8 black 65 4 30 270 / 90 

2L6 7 - 40 17 yellow 73 6 25 540 / 100 

2L6 7 - 40 17 yellow 63 6 25 540 / 100 

2L74 150 63 blue 55 8 20 670 / 124 

2L88 8 - 55 21 brown 72 6 25 540 / 100 

2L88* 8 - 55 21 brown 72 6 25 540 / 100 

2L88 8 - 55 21 brown 72 6 25 540 / 100 

2L54* 8 - 55 24 grey 55 10 25 535 / 124 

Worm pump S 5 (with slide-on Cardan shaft) 


(l/min) 




(˚Shore) 

D 6 Power D 4 Yellow 

D 4 Red 

Max. 

granulation 

(mm) 

Pump 

pressure 

(bar) 

Length/ 

diameter of 

stator (mm) 

D5* 3 - 18 6.5 red 73 4 40 270 / 90 

D6 Power* 3 - 18 6.5 red 73 4 40 270 / 90 

D8-2* 4 - 23 8.8 black 65 4 30 270 / 90 

2L54 8 - 55 24 grey 55 10 25 535 / 124 

2L6 4 - 40 17 yellow 50 6 25 540 / 100 

2L6 4 - 40 17 yellow 50 6 25 540 / 100 

2L6 4 - 40 17 yellow 63 6 25 540 / 100 

2L88 6 - 55 21 brown 50 6 20 540 / 100 

1,5L74 170 63 green 55 8 15 517 / 124 

2L6 7 - 40 17 yellow 73 6 40 540 / 100 

Worm pumps SP 11 

LMR, BMB, BMT, BMR, BBR, BUR 


(l/min) 




(˚Shore) 

Max. 

granulation 

(mm) 

Pump 

pressure 

(bar) 

Length/ 

diameter of 

stator (mm) 

2L6 4 - 40 17 yellow 50 6 25 540 / 100 

2L6 4 - 40 17 yellow 50 6 25 540 / 100 

2L6 4 - 40 17 yellow 63 6 25-30 540 / 100 

2L88 6 - 55 21 brown 50 6 20 540 / 100 

1,5L74 170 63 green 55 8 15 517 / 124 

2L6 7 - 40 17 yellow 50 6 25 540 / 100

D 8-2 2L88 2L6 2L6 maintenance-free Clamping jacket 




part no. 

Rotor 

part no. 

59 


part no. 

620 Groove/bore 211 355.007 521 150 010 433.007 

320 Groove 206 345.006 443 740 Maintenance-free 

320 Groove 436 746 436 743 Maintenance-free 

620 Bore 211 355.007 201 111.002 010 433.007 

620 Bore 430 837 201 111.002 Maintenance-free 

620 Bore 213 018.009 206 395.001 Integrated 

620 Bore 203 509.007 422 650 010 433.007 

620 Groove 203 509.007 211 815.000 010 433.007 

620 Bore 203 509.007 203 511.008 010 433.007 

620 Groove 523 235 211 739.005 Integrated 




part no. 

Rotor 

part no. 


part no. 



320 Groove 436 746 436 743 Maintenance-free 

620 Groove 523 235 211 739.005 Integrated 

620 Groove 16 211 355.007 211 814.001 010 433.007 

620 Groove 16 213 390.002 211 814.001 Integrated 

620 Groove 16 430 837 211 814.001 Maintenance-free 

620 Groove 16 203 509.007 211 815.000 010 433.007 


620 Groove/bore 211 355.007 521 150 010 433.007 




part no. 

Rotor 

part no. 


part no. 

620 Groove 16 211 355.007 211 814.001 010 433.007 


620 Groove 16 430 837 211 814.001 Maintenance-free 

620 Groove 16 203 509.007 211 815.000 010 433.007 


620 Groove/bore 211 355.007 521 150 010 433.007 




** depending on material, 

consistence, 

delivery range and pressure


2L54 grey 2L74 blue 2L74 silver 2L88 2L6 2L6 maintenance-free Clamping jacket 

Worm pumps SP 11 BHF 


(l/min) 



60 


(˚Shore) 

Max. 

granulation 

(mm) 

Pump 

pressure 

(bar) 

Length/ 

diameter of 

stator (mm) 

2L54* 0 - 105 24 grey 55 10 25 535 / 124 

2L54* 0 - 105 24 silver 72 8 25 535 / 124 

2L74 0 - 200 45.8 blue 55 8 25 670 / 124 

2L74* 0 - 200 45.8 blue 72 8 25 670 / 124 

2L75 0 - 200 75 grey 55 8 20 670 / 124 

2L75* 0 - 200 75 grey 55 8 20 670 / 124 

Other worm pumps 

Type Usage in 

machine 




(˚Shore) 

Max. 

granulation 

(mm) 

Pump 

pressure 

(bar) 

Length/ 

diameter of 

stator (mm) 

1L6 SP 5 14.8 yellow 50 6 15 270 / 100 

2L4 P4 5.3 yellow 50 4 20 360 / 75 

2L4 P4 5.3 red 72 4 25 360 / 75 

2L4 P4 5.3 green 72 4 25 360 / 75 

D3 TS3 10 red 72 4 25 315 / 70 

D3 TS3 10 green 72 4 25 315 / 70 

D5* MS-x, S 5 12 brown 65 4 20 350 / 90 

3L7 SP 11 BUR 17 yellow 50 6 40 534 / 100 

3L7 SP 11 BUR 17 yellow 75 6 40 534 / 100 

3D7 UMP 17 red 71 6 40 534 / 100 

2L6 FMP 17 yellow 50 6 25 540 / 100 

2L88 FUMP 70 21 brown 50 6 25 540 / 100 

2L88 UMP 21 brown 50 6 25 540 / 100 

2L74 P11 SDVF 63 blue 55 8 25 670 / 124 

2D8 FUMP, SP 11 E 45.9 red 72 4 25 600 / 145 

1,5L8 S8 123 yellow 50 10 15 660 / 190 

7515 SP 20 83 white 63 8 35 500 / 159 

2L8 SP 20 150 white 63 10 25 650 / 194 

N13 S MP 10 / P12 3.8 grey 73 4 30 160 / 60 

EW 40 Strobot 406 S 7 yellow 73 5 30 269 / 86

3L7 2L8 




part no. 

Rotor 

part no. 

61 


part no. 

620 Groove 16 523 235 211 739.005 Integrated 


746 Bore 206 396.000 206 395.001 Maintenance-free 


746 Bore 487 262 487 261 Maintenance-free 

746 Groove 16 502 911 500 516 Integrated 




part no. 

EW 40 N 13 S 

Rotor 

part no. 


part no. 

350 Groove S16 214 536.001 214 537.000 422 747 

407 Groove 010 325.005 010 321.009 010 329.001 

407 Groove 010 326.004 010 321.009 010 329.001 

407 Groove 010 677.009 010 321.009 010 329.001 

379 Groove 072 996.003 072 997.002 073 487.003 

379 Groove 201 175.006 072 997.002 073 487.003 

400 Groove 070 352.005 070 351.006 206 848.008 

620 Groove 16 213 638.007 211 278.003 Maintenance-free 



620 Groove 12 211 355.007 010 628.003 010 433.007 

620 Groove 14 203 509.007 208 316.004 010 433.007 

620 Bore 203 509.007 422 650 010 433.007 

620 Bore 206 396.000 206 395.001 Maintenance-free 


747 Bore 070 162.004 200 770.004 073 827.003 

623 Hexagonal 525 052 433 023 Maintenance-free 

740 Hexagonal H7000 508 312 H7000 508 021 Maintenance-free 

206 Groove 506 905 506 867 – 

312 Slot 463 793 506 909 Maintenance-free 




** depending on material, 

consistence, 

delivery range and pressure


Remixer 

62 

Part no. 

Uni-remixer (fig. 1) without union nuts 400 566 

(Accessories: see rotors with pins) 

Cross-shaped mixing paddle for uni-remixer 400 580 

2x union nut 208 801.001 

PM coupling V 35 / 25-40, reduced 207 795.008 

Pressure gauge 0-60 bar for hoses ID 25-40 214 570.009 

Pressure gauge 0-60 bar for hoses ID 35-40 472 506 

Pressure gauge, pressure monitor, T-piece 

Pressure gauge for ID 50 Part no. 

With coupling V 50 / grease deposit, 0-6 bar 011 729.008 

With coupling V 50 / grease deposit, 0-10 bar 011 730.000 

With coupling V 50 / grease deposit, 0-25 bar 426 387 

With coupling V 50 / grease deposit, 0-40 bar, 

diameter of 60 mm 

420 989 

With coupling V 50 / grease deposit, 0-100 bar 426 388 

T-piece for pressure gauge ID 50 mm 071 554.006 

Pressure monitor and gauge 

Pressure monitor cpl. with grease deposit, 2-32 bar 011 757.009 

Protective cap with pressure gauge NG 100 001 252.006 

Air test pressure gauge 1", T-piece, 0-6 bar, with Geka coupling 001 160.004 

Test pressure gauge with 1" hose nozzle ID 25 014 375.006 

Test pressure gauge with 1" hose nozzle ID 25-40 208 745.002 

Pressure gauge 0-60 bar for hoses ID 25-40 214 570.009 

Pressure gauge 0-60 bar for hoses ID 35-40 472 506 

M = female 

V = male 

S = spout 

Mortar hoses to 40 bar operating pressure 

(bulk stock, priced per metre) 

ID 25 mm, bulk stock 25 x 7 mm, 

from a 40 m role 





Mortar hoses, complete with coupling, 

ID 20, V 25-40 Geka 

Part no. 

001 602.009 

001 603.008 

501 913 

Part no. 

40 bar, 20 x 7 mm, length of 10 m 211 508.003 

Mortar hoses, cpl. with coupling, 

ID 25, 40 bar, M 25-40, V 25-40 


Part no. 

207 803.000 





Coupling V 25-40 / S 25 208 828.000 

Coupling M 25-40 / S 25 211 593.005 

ID 25 bulk stock, 25 x 7 mm 001 602.009 

4x hose clamp, ID 25, B 200 E 002 337.001 

Gasket for coupling 207 764.000


ID 25, 40 bar, V 35, V 25-40 


Part no. 

207 808.005 



Coupling V (a) V 25-40 / S 25 208 828.000 

Coupling V (b) V 35 / S 25 214 800.009 


4x hose clamp ID 35, D 250 e 002 337.001 


ID 35, 40 bar, M 35, V 35 


Part no. 

070 335.006 

40 bar, 35 x 8 mm, length of 13.3 m 207 615.007 



Coupling M 35 / S 35 211 594.004 

Coupling V 35 / S 35 206 606.004 


4x hose clamp, ID 35 B 250 e 002 331.007 



ID 35, 40 bar, M 35, V 50 

Part no. 

40 bar, 35 x 8 mm, length of 13.3 m 207 616.006 


Coupling M 50 / S 50 211 594.004 

Coupling V 50 / S 35 207 621.004 





ID 50, 40 bar, M 50, V 50 

40 bar, 50 x 9 mm, length of 13.3 m 

Part no. 

501 914 



Coupling M 50 / S 50 211 595.003 

Coupling V 50 / S 50 206 604.006 

ID 50 bulk stock, 50 x 9 mm 501 913 



63 

Putzmeister couplings for mortar hoses 

with 25-50 mm ID 

M 25-40 / RI 1" 

Part no. 

211 597.001 

M 35 / RI 1" 211 598.000 

M 35 / RI 11 ⁄2" 211 599.009 

M 50 / RI 2" 211 600.008 

M 35 / RA 1 1 ⁄2" 070 315.000 

M 50 / RA 2" 211 848.006 

V 25-40 / RI 1" 207 763.001 

V 25-40 / RI 1 1 ⁄2" 207 813.003 

V 35 / RI 1" 207 618.004 

V 35 / RI 1" plastic 203 135.002 

V 35 / RI 1 1 ⁄2" 070 316.009 

V 35 / RI 2" 208 453.006 

V 35 / RI 5 ⁄4" 207 635.003 

V 50 / RI 2" 205 273.001 

V 50vRI 1" 207 629.006 

V 50 / RI 2 1 ⁄2" 210 793.000 

M 25-40 / S 25 211 593.005 

M 35 / S 35 211 594.004 

M 50 / S 50 211 595.003 

V 25-40 / S 25 208 828.000 

V 35 / S 25 214 800.009 

V 35 / S 35 206 606.004 

V 50 / S 50 206 604.006 

V 50 / S 35 207 621.004 

V 35-V 25 / 40, reduced 207 795.008 

V 25 Geka 531 291 

V 35 Geka 531 288 

M 25 / 40-V 25 208 838.003 

V 50 - M 35 tapering 213 217.004 

M 50 - V 35 tapering 211 290.007 

V 50 self-sealing coupling 208 454.005 

Rotary feedthrough 

Part no. 

M 25-40 / RI 1" aluminium coupling, cpl. 403 330 

Hose spouts with thread 

for mortar hoses with 20-50 mm ID 

S-spout, 20 mm, RA 1" 

Part no. 

211 536.004 

S-spout, 25 mm, RA 1" 205 464.001 

S-spout, 35 mm, RA 1 1 ⁄2" 205 465.000 

S-spout, 50 mm, RA 2" 205 466.009 

M = female 

V = male 

S = spout 

Accessories for plastering machines


Sealing rings 

64 

Part no. 

ID 25-40 mm, 42 x 27 x 6 mm 207 764.000 

ID 35 mm, 54 x 37 x 6 mm 213 725.004 

ID 50 mm, 67 x 51 x 6 mm 213 266.000 

Hose clamps 

Part no. 

ID 25 mm, for mortar hose B20 Oe. 002 337.001 



ID 65 mm, 2-part, for mortar hose B25 015 288.008 

ID 90 mm, for mortar hose 016 337.000 

ID 98 mm, for suction hose 002 247.007 

Width Hose, external Part no. 

8.1 mm Diameter of 6-16 mm 002 333.005 




12.0 mm Diameter of 57 mm 001 433.003 


Hose clamps for air hoses 

Width Hose, external Part no. 

8 mm Diameter of 15-17 mm 002 328.007 



Cam lever 

Part no. 

Reinforced cam lever, cast steel 211 535.005 

Heavy-duty, reinforced dowel pin (10 pcs delivered in set): 

– For 35 and 25 female parts, size 6/30 and 3.5/30 441 055 

– For 50 female parts, size 6/40 and 3.5/40 441 056 

Spiral dowel pin for 25 and 35 parts, 6 x 28 211 613.008 

Spiral dowel pin for 25-40, 6 x 30 211 609.009 

Spiral dowel pin for 50, 6 x 36 211 610.001 

Retaining ring for cam lever 001 698.000 

Water hose 3 ⁄4" 

Water hose, GEKA coupling 

Part no. 

3 ⁄4" ID, length of 40 m 210 789.001 

Spray nozzle, GEKA coupling 1 ⁄2" ID, can be shut off 042 419.002 

Air hoses 1 ⁄2" 

Coupling Length Part no. 

GEKA 1 ⁄2" ID 10 m 001 682.003 

GEKA 1 ⁄2" ID 15 m 212 333.002 

GEKA 1 ⁄2" ID 20 m 001 665.004 

GEKA 1 ⁄2" ID 40 m 214 734.007 

Air hoses EWO 

Diameter Length Part no. 

10 mm 10 m 463 791 

10 mm 25 m 462 721 

EWO coupling 

Part no. 

RA 1 ⁄2" 213 269.007 

GEKA quick-release couplers for water and 

air hoses with 3 ⁄8"-1" ID" 

Sealing, GEKA plus 

Part no. 

413 895 

Gasket 002 313.009 

S 3 ⁄8" 018 535.004 

S 1 ⁄2" 002 312.000 

S 3 ⁄4" 001 387.007 

S 1" 001 390.007 

RA 3 ⁄8" 041 403.006 

RA 3 ⁄4" 001 386.008 

RA 1" 062 815.000 

RA 11 ⁄4" 062 861.009 

RA 1 ⁄2" 014 068.009 

RI 1 ⁄2" 062 621.003 

RI 3 ⁄4" 002 311.001 

RI 1" 001 391.006 

RI 11 ⁄4" 062 622.002 

RI 3 ⁄8" 424 458 

S = spout RA = outer thread RI = inner thread

Fine plaster spray gun, plastic, for premixed dry mortar 

To a granulation of 4 mm for all premixed dry mortar to be reworked, 

e.g. gypsum plaster, lime cement plaster etc., max. throughput of 30 l/min, 

air requirement of approx. 200 l/min. 

Nominal diameter Mortar 

nozzle 

M 25-40 with swivel 

coupling 


coupling 


coupling 


coupling and angled 

aluminium head 


coupling and angled 

aluminium head 

Air nozzle Model Nozzle 

diameter 

65 

Weight Fig. Part no. 

yes 2 Short, 300 mm 14 mm 2.4 kg 5 408 237 

– 1 Short, 405 mm 14 mm 1.2 kg 1 402 592 

MP 25 Standard 

– 1 Long, 1,460 mm 14 mm 2.6 kg 1 403 812 

– 1 Long, 770 mm 14 mm 1.2 kg 2 404 479 

– 1 Long, 1,185 mm 14 mm 1.5 kg 2 404 361 

V 35 mm – 1 Short, 285 mm 14 mm 0.6 kg 3 203 054.002 

V 35 mm yes 1 Short, 450 mm 14 mm 0.65 kg 4 209 174.009 

Mortar nozzles, conical 

Diameter Part no. 

10 mm 521 640 

12 mm 521 641 

14 mm 521 642 

16 mm 521 643 

Rubber fine plaster nozzles 

Diameter Quality PE 

part no. 

Quality PU 

part no. 

8 mm 214 751.006 417 556 

10 mm 214 752.005 417 974 

12 mm 214 753.004 410 982 

14 mm 214 754.003 417 554 

16 mm 214 755.002 417 555 

Rubber collar nozzles 


18 mm 001 329.007 

20 mm 001 330.009 

Base coat plaster spray guns, aluminium, 

for freshly prepared mortar and site-made mixes 


Up to a maximum granulation of 8 mm, can be used for base spray plaster, base 

coat plaster, scraped plaster, and insulating plaster, primarily suited for dry 

materials but can also be used for site-made mixes. Max. throughput of 40 l/min, 

air requirement of approx. 200-400 l/min. All 3 spray guns are in ID V 35 and have 

2 air cocks and 1 bore. 

Model Nozzle diameter Weight Part no. 

Short, 185 mm, straight 20 and 16 mm 1.4 kg 001 306.004 

Short, 700 mm, angular 20 and 16 mm 1.5 kg 209 307.009 

Long, 1,300 mm, angular 20 and 16 mm 1.7 kg 209 308.008


Structure spray guns 

For a granulation of up to approx. 4-6 mm, mineral/dispersion 

plasters, sealing slurry, filling compounds etc., throughput of up 

to 10 l/min, air requirement of 400-800 l/min. 

ID Nozzle diameter Weight Part no. 

M 25 mm 4, 6, 8 mm 2.2 kg 071 473.006 

M 25-40 mm 4, 6, 8 mm 2.2 kg 208 751.009 

Refurbishing spray gun 

For a granulation of up to 6 mm for special mineral 

renovation plasters, concreting with a ring nozzle and 

flexible spray tube. 


ID 1", diameter of 12 mm nozzle, 

RI1" AG, weight of 1.2 kg 

207 283.002 

ID V 35 / RI1", 

coupling connection – plastic 

203 135.002 

ID M 25-40 / RI1", coupling connection 211 597.001 

Vulkollan nozzle jet 

diameter 15 mm 207 286.009 

Joint and frame filling devices and cable remote controls 

Concrete spray nozzles, plastic 

ID Air cock Accessory 

for air cock 

66 

Spray nozzles for structure spray gun 


4 mm 000 225.005 

6 mm 000 227.003 

8 mm 000 229.001 

9 mm 000 230.003 

10 mm 000 231.002 

Material nozzles for structure spray guns 

Diameter Diameter / 

model 

12 mm Air bores, diameter 

of 3 mm – red 

12 mm Air bores, diameter 

of 2 mm – silver 

Nozzle 

diameter 

Part no. 

206 734.002 

206 751.001 

Weight Part no. 

V 35 mm 1 1 28 mm 3.0 kg 011 780.005 

V 50 mm 1 2 30 mm 3.5 kg 072 157.004 

Applying nozzle 

Part no. 

RI1"/GEKA mortar applying nozzle, 160 mm wide 071 566.007 

Inner nozzle diameter Part no. 

ID 10 Joint device with tangent. spray head and joint nozzles, swivel coupling M 25-40 415 689 

ID 25 Frame connector filling device with ball valve, swivel coupling M 25-40, 

as per fig 20 m with e-remote control cable (for MP + Sprayboy) 

214 236.000 

Remote control cable with Binder connector and switch, 20 m long 214 254.008 

ID 25 Frame connector filler hose with coupling M 25-40, 30 cm long 408 373 

E-remote control with on/off switch (Binder connector), 60 m 269 446.007 

E-remote control cable with connector (Binder) for extension, 30 m 211 507.004 

E-remote control cable with connector (Binder) for extension, 20 m, 3 x 0.75 211 506.005 

E-remote control cable with connector (Binder) for extension, 10 m, 3 x 0.75 211 505.006

Adhesive guns (boxed sets) 

Coupling Part no. 

For PM coupling, consisting of: 

408 422 

adhesive gun cpl., toolbox 410, 

cleaning brush D, grease gun - small, 

adapter cable, Harting/Binder, 

with PM coupling 

We recommend: 

20 m remote control cable 211 506.005 

Injection nozzles 

1 2 

3 

Compressors 

Fig. Part no. 

Compressor, 200 l/min, 400 V / 50 Hz, 3-phase, 

without cut-out (MP series) 

1 481 074 

Compressor, 180 l/min, 230 V / 50 Hz, 1-phase, with cut-out 1 481 087 

HANDY compressor, 250 l/min, 400 V / 50 Hz, 3-phase 2 000 235.008 

HANDY compressor, 250 l/min, 230 V / 50 Hz, 1-phase 2 000 215.002 

Coupling 1 ⁄4" GEKA (*) 

(*) Required if compressor is not used in conjunction with a mixer pump 

Coupling Part no. 

Injection nozzle, cpl. with T-piece, pressure gauge, 

remote control air cock, coupling with spout ID 50, 

mounted expanding collar D 45, and collar D 38 

001 128.004 

Injection nozzle as above but without T-piece, without pressure 

gauge, and without remote control cock, connection V 35/RI 1" 

001 133.002 

Expanding collar D 38 070 344.000 

Expanding collar D 45 070 345.009 

67 

207 969.009 

Compressor, V-MEKO 400, 360 l/min, 

400 V / 50 Hz, with pressure cut-off 

3 400 168 

Compressor, V-MEKO 400, 360 l/min, 

400 V / 50 Hz, without pressure cut-off 

3 205 767.009 

Compressor, V-MEKO, 360 l/min, 3 x 220 V / 60 Hz 3 210 072.006 

Compressor V-MEKO, 360 l/min, 3 x 380 V / 60 Hz, 

with pressure cut-off 

3 462 267 


Hopper sprayguns with 

accessories 

Part no. 

Hopper spraygun, 207 307.001 

cpl. with air hose 

in box 

Hopper spraygun 210 014.006 

without hose and 

packaging 

Air hose with 209 345.003 

EWO plug coupling, 

10 m 

Air hose with 207 958.007 

EWO plug nipple/ 

GEKA coupling 

Stands for 

206 766.009 

hopper sprayguns 

Angle piece 001 430.006

Accessories for fine concrete pumps 

Rotary distributor (RV) 

Rotary distributors are ideal for the simple and flexible delivery and distribution 

of fine concrete at construction sites. There are different rotary distributor sizes to 

be used in accordance with different site conditions. 

Technical data: 

Type Delivery 

pipeline - ID 

3153 

2466 4562 

Arms Reach (m) Concreting 

area (m 2 ) 

5418 

68 

1995 

1200 

Transport 

dimensions, 

L x W x H (m) 

6580 

Weight 

(kg) 

5497 

Part no. 

RV 0 125 – – – 0.8 x 0.5 diameter 68 500 570 

RV 7 125 2 6.58 132 4.2 x 0.6 x 0.8 610 455 597 

RV 10 125 2 10 320 7.10 x 1.03 x 1.76 1.020 426 078 

RV 0 Part no. 

The RV 0 is the smallest rotary distributor in 

500 570 

the range. It is particularly suited to cramped 

construction sites. This compact, hand-guided 

additional unit for concrete distribution has an 

unrestricted slewing circle. 

RV 10 Part no. 

The RV 10 is a flexible rotary distributor which 

is ideal for large areas and roofs. Large areas 

of up to 320 m2 426 078 

can be concreted from one fixed 

location. 

Accessories for the RV 10 

Possible concreting area 

Part no. 

Underlay plate, 1 set, 4 pcs 481 026 

Possible concreting area 

RV 7 Part no. 

The RV 7 is suitable for small construction sites 

455 597 

on roofs and for the concreting of pillars. The RV 7 

is stabilized by 6 individual weights which can be 

removed in order to transport it. 

Manual gate valve GVM 

GVMs (manual gate valves) are simple shut-off gates. They are 

opened and closed manually, i.e. using a hammer. They are available 

for low pressure requirements of up to 20 bar and for high pressure 

requirements of up to 130 bar. 

Manual gate valve GVM 2/2, 130 bar, SK 125, 5.5" 

Part no. 

413 087 

Manual gate valve GVM 2/2, 130 bar, SK 100, 4.5" 222 362.005

Delivery lines 

Part no. 

Delivery pipe SK 50, 3", 1,000 mm 081 783.003 






Delivery pipe SK 100, 4.5", 1,000 mm 056 861.002 









Delivery line bend 

Part no. 

Delivery line bend SK 50, 3", 45° 081 779.004 




Delivery line bend SK 100, 4.5", 15° 057 595.005 



Delivery line bend SK 100, 4.5", 90° 421 329 





Junctions and taperings 

69 

Part no. 

T-delivery pipe SK 100, 4.5", 1,000 mm 057 614.009 

T-delivery pipe SK 125, 5.5", 1,000 mm 057 615.008 

Reducer pipe SK 65, 3"- SK 50, 3", 1,000 mm 058 670.000 

Reducer pipe SK 100, 4.5"- SK 50, 3", 1,000 mm 224 269.009 

Reducer pipe SK 100, 4.5"- SK 50, 3", 1,500 mm 238 508.002 

Reducer pipe SK 125, 5.5"- SK 100, 4.5", 1,000 mm 057 604.006 

Transition piece SK 3"/2" IG 027 716.005 

Transition piece SK 3"/2" AG 082 784.001 

Wash-out port lid for T-delivery pipe, 4.5" 057 627.009 

Wash-out port lid for T-delivery pipe, 5.5" 057 628.008 

Pressure gauge 

Part no. 

Pressure gauge SK 4.5", 100 bar 521 430 

Pressure gauge SK 5.5", 100 bar 521 448 

Clamp couplings 

Part no. 

Clamp coupling SK 3" 417 798 

Clamp coupling SK 4.5" 431 613 

Clamp coupling SK 5.5" 417 249 

Securing cotter pin 


Part no. 

Securing cotter pin 018 878.004


Delivery hoses 

Part no. 

Delivery hose SK 50, 3", 2,000 mm 481 169 





Delivery hose SK 100, 4.5", 3,000 mm 253 319.001 





Delivery hose SK 125, 5.5", 3,000 mm 433 497 





End hose SK 50, 3", 6,000 mm 292 067.000 

End hose SK 65, 3", 5,000 mm 404 454 

End hose SK 100, 4.5", 2,850 mm 233 647.007 

End hose SK 125, 5.5", 3,000 mm 233 649.005 

Support holder for end hose, SK 100, 4.5" 054 370.003 

Support holder for end hose, SK 125, 5.5" 054 371.002 

Gaskets 

Part no. 

Gasket ID 65, ID 50, 3" 064 084.004 

Gasket ID 100, 4.5" 057 341.000 

Gasket ID 125, 5.5" 055 559.001 

Concrete spray gun 

Concrete injection nozzle, plastic, ID V 50 mm, 

1 air cock, 1 accessory for air cock, 30 mm nozzle 

diameter, weight of 3.5 kg 

Part no. 

072 157.004 

70 

High-pressure concrete spray gun 

With rubber nozzle 2, AG 

Part no. 

532 589 

Concrete injection nozzle 532 590 

Cleaning accessories 

Sponge ball D 60, hard version 

Part no. 

000 212.005 

Sponge ball D 70, hard version 258 320.008 

Sponge ball D 80, hard version 000 246.000 

Sponge ball D 120 016 091.003 

Sponge ball D 150, hard 223 673.007 

Sponge ball D 150, medium 018 841.002 

Catch basket for sponge balls, 4.5" 276 715.006 

Catch basket for sponge balls, 5.5" 276 593.008 

Wash-out adaptor SK 4.5", 

for cleaning with compressed air 

057 616.007 

Wash-out adaptor SK 5.5", 

for cleaning with compressed air 

057 617.006 

Special accessories 

Pipe clamp for wall or floor, ID 100 

Part no. 

052 930.005 

Pipe clamp for wall or floor, ID 125 051 038.005 

Air hose 3⁄4", 20 m 416 015 

PM hose carriage 482 464 

PM pump aid, 18 l storage tank, 25 pcs 266 743.004

For cleaning delivery hoses 

Rubber sponge balls Diameter mm Part no. 

For delivery hose ID 13 mm 19 470 376 



For delivery hose ID 25 mm 30 000 239.004 



For delivery hose ID 60 + 65 mm 80 000 246.000 



For cleaning and maintenance 

PM hand lever grease gun with hose 

Part no. 

000 211.006 

Grease cartridges with high-performance 

lubricating grease, 400 g 

000 113.007 

Grease gun, small 000 112.008 

Cleaning brush 000 100.007 

PM spray gun incl. 5 m hose 000 210.007 

Cleaning spray device, V 35, aluminium, 

short without nozzle, with air fitting 

211 564.005 

Nozzle, steel, diameter of 8/14 210 127.003 



Cleaning agent and preservative 

Limpiol 354 

20 l can 

(enough for approx. 400 - 600 m 2 ), 

biodegradable 

410 139 


Machine and work accessories 

Chock – steel plate 636 

Part no. 

015 006.002 

Chock – plastic UK 10 415 904 

Chock – plastic UK 36 484 954 

Bracket for UK 36 484 956 

Bracket for UK 10 415 905 

Holder for 636 061 362.004 

Trailer lighting holder, 

1.6 m cable 


1.6 m cable 


1 m wide, 6 m cable 


1 m wide, 6 m cable 

71 

General accessories 

13-pin connector, 12 V 496 261 

13-pin connector, 24 V 507 177 

7-pin connector, 24 V 209 028.003 

7-pin connector, 12 V 207 525.003 

Car cable adapter, 13- to 7-pin connector, 12 V 437 679 

Car cable adapter, 7- to 13-pin connector, 12 V 248 012.009 

Licence plate bracket with hinged frame 362 732.003 

Safety helmet, yellow, with PM overprint 064 626.006

General accessories 

Power cable/construction site lead 

72 

Part no. 

Extension cable, 16 amps, 230 V 3 x 2.5 mm 2 , 20 m 212 960.006 

Construction site lead with CEE plug, 16 amps, 10 m, 5 x 2.5 mm 2 211 457.002 



Construction site lead with CEE plug, 32 amps, 25 m, 5 x 4 mm 2 062 922.003 

Construction site lead with CEE plug, 32 amps, 50 m, 5 x 4 mm 2 062 923.002 

Cable drum 

Part no. 

Cable drum with 40 m of 230 V cable and 4x 230 V sockets 463 811 

Cable drum with 25 m 380 V cable and 4x 230 V sockets, 

fuse for every two sockets, 16 amps 

482 853 

Main power cable 

Main power cable, 230 V, 5 m (406 S) 

Part no. 

470 368 

Main plug, 230 V 470 370 

Distributor 

Distributor, 380 V, 32 amp supply voltage 

and power socket, 380 V, 16 amps and 4x 230 V sockets 

Part no. 

463 819

Conditions of sale and delivery 

(Last updated in January 2002) 

I. Scope 

1. The following conditions shall apply to all deliveries and services, regardless of whether these deliveries and 

services relate to an individual purchase or works order or to a contractual relationship. 

2. Purchasing conditions and other commercial requirements of the purchaser shall not apply, even if the supplier 

has not clearly rejected these conditions. 

II. Contract conclusions and alterations, assignment 

1. The documents pertaining to the offer (e.g. pictures, drawings) and also information relating to the products 

supplied, appearance, services, dimensions, weights, fuel-consumption, operating costs, etc. shall only be 

decisive in that they are not expressly designated as binding. The supplier reserves the property rights and 

copyright for cost calculations, drawings and other documents. These must not be made accessible to third 

parties and must be returned upon request. 

2. The contract is concluded when the supplier confirms acceptance of the order in writing or the supplier has 

already commenced the delivery or the service. If the supplier has indicated a delivery date for the offer, the 

contract is confirmed when the ordering party confirms acceptance of the offer promptly. 

3. Verbal subsidiary agreements when concluding a contract or changing the contract shall require written 

confirmation from the supplier in order to become effective. Obvious spelling or calculation errors can be 

corrected at a later stage. 

4. The purchaser is not authorized to transfer their rights from this contract. 

III. Prices 

1. The prices shall apply ex works including loading in the factory, but excluding packaging, and plus the legal VAT 

in accordance with the respective conditions in force in the country in which the supplier will deliver or provide 

the service. If the method for crediting the supplier has not been confirmed, the prices valid on the day of delivery 

shall be binding. 

2. The prices of engineering work, assembling and putting into service shall be calculated separately. The invoicing 

can be in the form of a lump sum or a reflection of actual expenditure plus travel costs, living and accommodation 

costs, overtime, Sunday and Bank Holiday entitlements. 

3. Price alterations are permitted if more than 6 months elapse between the date the contract was concluded and the 

agreed date of delivery. The supplier is entitled to adapt the price in such a way that the new price has the same 

relationship with the price originally agreed, as the price for delivery and service in accordance with the price list 

applicable on the day of delivery with the price for delivery in accordance with the price list applicable on the day 

the contract was concluded. With regard to other deliveries and services not featured in a price list, the supplier is 

entitled to adapt the price appropriately, in response to circumstances. 

4. If the prices contain costs or fees and these increase after the contract has been concluded or if they become applicable 

after the contract has been concluded, the supplier is entitled to charge the additional costs to the purchaser. 

5. If the supplier is willing to exchange upon the supplier’s request, the supplier is entitled to forward the ensuing 

costs, or at least the sum totalling an extra 10 % of the original price - as a result of a fall in value associated with 

ageing and use - of the object originally to be delivered as a compensatory payment for the expenditure incurred 

by the supplier when exchanging the object. The above-mentioned cost totals cannot be demanded by the supplier 

if the purchaser proves that the supplier has incurred either no expenditure or minimal expenditure. 

IV. Payment, delayed payment, offsetting, withholding payment 

1. If no contrary arrangement has been made, deliveries of machines must be paid for within 7 days of delivery, 

spare parts within 30 days and services within 14 days of the invoicing date, without delaying. 

2. All payment demands - even those for work hours or other payment issues - shall be due immediately, as soon 

as the purchaser delays for more than 5 days in fulfilling even just a part of his commitment to the supplier or if 

circumstances occur which significantly decrease the credit status of the purchaser (e.g. capital losses, payment 

adjustment, over-indebtedness, exchange rate and cheque bounces, filing for insolvency or declaring or rejecting 

the status of insolvency). In this case, the supplier may refuse further deliveries and services and demand the 

adoption of suitable safety measures. 

3. Payments involving a currency exchange require a specific arrangement. Foreign currency and checks are only 

accepted for payments. Collection and discount charges shall be borne by the purchaser. No discount is guaranteed 

for bills of exchange and superfluous payments, even if a discount had already been arranged. 

4. The purchaser may only countercharge the supplier if he has a legal or uncontested right to do so. The purchaser 

is only entitled to withdraw if his counterclaim relates to the same contractual relationship and has an uncontested 

or legal basis, or if the supplier has severely breached his duties from the same contractual relationship. The 

right of the purchaser to withhold an appropriate section of the purchase price due to shortcomings in the service 

received shall remain unaffected. 

5. If the purchaser enters into arrears, the supplier’s charges shall be charged at 8 % interest over and above the 

basic interest rate. The supplier’s right to have further damage replaced remains unaffected. 

6. If the purchaser should incur a deterioration in wealth as described in section IV. 2, the supplier may withdraw 

from the contract. Further legal claims from the supplier - such as compensation - shall remain unaffected. Claims 

from compensation from the purchaser are excluded. 

7 If Putzmeister accepts payment for a used machine, the following shall apply: 

a) The contracting partner is obliged within 2 weeks of Putzmeister receiving the machine to submit the original 

documents required relating to using and operating the machine as road traffic. 

b) If the original papers are not submitted to us on time, we are entitled to issue a reminder to the partner and also 

to impose a time limit of 2 weeks for submitting the documents with the declaration that after this date has expired 

Putzmeister will refuse to accept the papers and also to pay for the used machine. 

c) If this deadline expires the other contract partner shall owe us the invoice amount for the used machine and 

also a compensatory sum of EUR 250,00 for the expenditure incurred, in addition to VAT. The partner is entitled to 

prove that the expenditure did not occur or that it was considerably lower than the sum given. The used machine 

shall be returned to us at our company headquarters. 

V. Delivery time, partial delivery, delayed acceptance 

1. Supplier and assembly deadlines do not begin until the supplier and the purchaser have agreed upon all the details 

to be carried out and all the conditions of the transaction and not before the supplier has confirmed the order. 

They will remain inactive in so far as the purchaser is behind in the fulfilling of their obligations from this contract 

(e.g. providing documents, providing materials, approvals, releases) or in the payment that had been arranged. 

2. The delivery time shall be respected if the object to be delivered has left the factory by the time that the date is due, 

or the company has notified the partner of their intention to despatch the object. 

3. The delivery time shall be extended in the event of extreme force, strikes, sieges and other extraordinary and 

unexpected circumstances, even if a pre-supplier is affected, provided that these circumstances can be proved to 

have affected the delivery time. 

4. If the supplier’s delivery is delayed, the supplier shall not be considered to be in arrears provided that this is due 

to circumstances that could not be foreseen and prevented by inexpensive and expected cautionary measures and 

could not be overcome with appropriate measures. 

5. The supplier is entitled to withhold the delivery if the ordering party does not fulfil his obligations towards the 

supplier resulting from this or from another contract or from another legal cause. 

6. Partial deliveries are permitted if acceptable for the purchaser. They shall count as independent transactions, 

which shall be calculated separately. 

73 


7. If the payment conditions are not satisfied, the delivery is not received on time or is refused or if, in accordance 

with item IV. 2, safety measures arranged or which become due are not put into place, the supplier is entitled to 

withdraw from the contract and to demand compensation if a deadline imposed is not fulfilled. The supplier can 

demand from the purchaser without proof 25 % of the cost for series products and 75 % of individually produced 

orders as compensation, as long as the purchaser does not prove that either no expenditure or very minimal 

expenditure was incurred. Further claims for higher levels of damage proven remain unaffected. 

8. If the despatch is delayed on the part of the purchaser, the supplier can either charge the actual storage and maintenance 

costs or a lump sum amounting to 1 ⁄2 % of the invoice amount per month; however, he may not do this 

if the purchaser proves that the supplier incurred no or very little damage or expenditure. The payment obligations 

of the purchaser remain unaffected. 

VI. Risk bearing, despatching and receiving 

1. The risk is transferred at the latest when the object to be delivered is sent to the purchaser. This also applies to 

partial deliveries or when the supplier has taken over the costs of the consignment or the assembly or has undertaken 

to convey it himself. No liability shall be accepted for cost-effective freight transport methods or transport 

lead times. 

2. If the delivery, the despatch or the acceptance of the item to be delivered are delayed by the purchaser through no 

fault of the supplier, all risks including the risk of deterioration or decline of the item to be delivered and also all 

risks related to the item itself shall be transferred to the purchaser - once readiness to despatch or notification of 

completion has been communicated to the purchaser. 

3. On written request, the consignment can be insured to the amount required at the expense of the purchaser. 

4. The purchaser shall be liable for all damage caused by him during or after reception of the item delivered 

(e.g. during testing or during acceptance procedures). 

5. Items delivered must be received by the purchaser, even if they display shortcomings. 

VII. Notification of defects, warranties, periods of warranty 

1. The purchaser must inspect the item delivered immediately after receiving it and notify the supplier of any defects 

in writing and without delay. The purchaser must also check that the item delivered has no faults before each time 

that it is put into service and in particular, ensure that it is safe and can be used. The item delivered must be constantly 

monitored for safety and for faults whilst in operation. Even if the reservations regarding usability or safety 

are only minimal, the item must not be used or must be switched off immediately. The supplier must be informed 

in writing immediately in the form of a quality complaint which refers to the reservations or the faults in question. 

The purchaser must provide the supplier with the time and opportunity with which to carry out the necessary 

improvements and replacement delivery. If not, the supplier will no longer be liable for the consequences. 

2. If there are shortcomings in the supplier’s transfer of risks, the supplier can rectify this after deciding whether to 

repair the fault or to deliver a new item containing no defects in exchange for the faulty item delivered. All replacement 

items are the property of the supplier. If a shortcoming for which the supplier is responsible cannot be rectified, 

if the rectification is faulty and cannot be corrected or if it is implausible for the purchaser or if the vendor has 

refused both types of rectification, or if a deadline imposed on the supplier for the purpose of rectifying the fault 

has expired, the purchaser may decline to credit the supplier or choose to withdraw from the contract. If the fault is 

only minimal, the purchaser still has a right to reduce the credit to the supplier. 

3. If the supplier maliciously conceals a fault on the item or takes over the warranty for the quality of the item, the 

legal regulations shall apply. 

4. If the purchaser or a third party rectifies the fault independently, this will result in the loss of all quality claims 

against the supplier. The costs of the rectification carried out by the purchaser or a third party without prior express 

agreement from the supplier shall not be borne by the supplier. This rule shall not apply in urgent or, in particular, 

irreparable cases where operational safety is jeopardized or where disproportionately large damage must be 

prevented. In such cases, the supplier’s agreement must be sought immediately and the supplier must commit to 

refunding necessary costs only. 

5. The supplier shall not pay any warranty or take on any obligation for the damage, particularly in the following cases: 

unsuitable or unprofessional use of the item, incorrect assembly or placing into service of the item by the purchaser 

or a third party, natural wear and tear, incorrect or careless treatment of the item, improper maintenance, excessive 

use of or stress on the item, the use of unsuitable operating equipment and unsuitable alternative materials, deficient 

works, unsuitable building ground, chemical, electrotechnical/electronic or electrical influences. This exclusion 

shall not apply, however, if the damages are the responsibility of the supplier because the correspond more closely 

to the rules in section VIII. item. 5. The supplier shall also incur no liability or obligation for the following measures 

and actions carried out by the purchaser or a third party and for the consequences of this: unprofessionally 

executed rectification, modification of the item delivered without prior agreement from the supplier, adding and 

installing further components, particularly spare parts, which did not originate from the supplier or which were 

approved expressly for the assembly and also failure to comply with the operating and user instructions. 

6. The supplier shall not pay any warranties if the item was produced with the purchaser’s materials or from specifications 

or designs produced by the purchaser. 

7. When selling used machines, appliances or components, the supplier shall not pay any warranties resulting from 

any faults on the item. The supplier shall not make promises relating to any features and shall indicate that used 

machines and also many used components cannot deliver the same usability or provide the same features as newly 

produced machines and parts. 

8. The purchaser’s requests for rectification and also the claims communicated to the purchaser with regard to damages 

or refunded expenditure due to faults shall expire one year after delivery of the goods, and if the fault becomes 

apparent during assembly, one year after the end of the assembly work. If the reception or acceptance of the delivery 

and the service is delayed through no fault of the supplier, the warranty shall expire at the latest 12 months after 

completion. The same also applies to subsequent rectification. If the supplier maliciously conceals the fault or claims 

warranties relating to the composition of the item, the claims from the purchaser shall be subject to the legal 

regulations with regard to time-barring of claims. The legal regulations also apply for the ageing of any claims for 

damages from the purchaser due to faults, when the supplier has been grossly or intentionally negligent or if the 

claim for damages relates to a death to a physical injury, or to damage to health. 

9. All remaining claims from the purchaser, particularly those relating to damages and also to damage which has not 

been caused to the item itself are excluded from the above. Item VIII. 5. applies accordingly.


VIII. Rescission, compensation and time-barring 

1. The purchaser can withdraw from the contract if the entire service provided by the supplier becomes impossible 

to provide before the risks are transferred. A claim from the purchaser for damages due to complete inability to 

provide the service is excluded, unless the supplier is very clearly at fault for this. Any claims for damages shall 

be limited to damage which was foreseeable at the time of concluding the contract because it resulted from normal 

circumstances and the amount of the damages payable shall not exceed 15 % of the contractual amount. The 

purchaser can also withdraw from the contract if, when ordering similar items, the execution of part of the delivery 

becomes in possible due to the amount, and it is in the purchaser’s interests to reject this partial delivery. If this is 

not the case, the purchaser can reduce their contractual fulfilment accordingly. 

2. If the impossibility of receiving part of the delivery is established when delaying the acceptance or due to the fault 

of the purchaser the purchaser is still obliged to fulfil their part of the contract. 

3. The purchaser can withdraw from the contract if the supplier is late in fulfilling their part of the contract, and, if 

applicable, the purchaser has issued an appropriate deadline to the supplier without success and the supplier 

is therefore responsible for non-fulfilment of the contract. A claim from the purchaser for damages due to late 

fulfilment by the supplier is excluded, unless the supplier is clearly at fault. Any claim for damages shall be 

limited to damage which occurred through normal circumstances and which was foreseeable when the contract 

was concluded and the amount payable shall not exceed 1 ⁄2% for every full week affected by the delay. It shall not 

exceed a total of 5 % of the value of the part of the delivery which could not be used on time due to the delay. 

4. The purchaser’s right to withdraw from the contract in accordance with the legal regulations and due to breach 

of obligations by the supplier and not relating to a product fault remains unaffected - over and above the cases 

covered in sections 1 and 3. 

5. All further claims from the purchaser, particularly those relating to termination and claims for damages, including 

claims for damages in place of services and claims for rectification of damage of any kind and with any legal basis, 

also resulting from breach of pre-contractual and contractual obligations and from unauthorized actions carried out 

at the beginning of the contract or when developing or concluding the contract namely, for rectification of damage 

not caused to the item itself are excluded. This exclusion of liability shall not apply if the supplier suffers gross 

negligence. This exclusion of liability shall also not apply when the supplier has breached their contractual obligations. 

This exclusion of liability shall also not apply for any claim from the purchaser for damages, which relate 

to death, injury to health or to physical injury as a result of intent or negligence. This exclusion of liability shall 

not apply in cases where liability is greater in accordance with product liability legislation and relates to personal 

injury or damage to privately-used items. If the supplier’s liability is proven in accordance with the above or - in 

deviation from the conditions below - is also justified in other cases on contractual or legal grounds, this liability 

shall be limited to the replacement of foreseeable damage which occurred through normal circumstances and can 

be proved as individual cases. This limitation of liability shall not apply for any liability in accordance with product 

liability legislation resulting from personal injury caused by items delivered or for damage to privately-owned 

items. This limitation of liability shall also not apply if the supplier incurs a malicious act intent or gross negligence. 

6. Claims for damages filed against the supplier by the purchaser - whether due to breach of pre-contractual and 

contractual obligations due to unauthorized actions carried out during the initiation, development or conclusion of 

the contract or from any other time-barred legal basis within a year from the end of the year during which the claim 

arose and the purchaser from whom the circumstances justifying the claim and from whom information is obtained 

or should be obtained without gross negligence. If the debtor is the victim of gross negligence or a malicious act, 

the legal regulations shall apply. The legal regulations shall also apply for claims for damages relating to injury to 

life, health or physical injury resulting from intentional acts or gross negligence. 

7. The supplier’s managing director and his colleagues shall be liable to the purchaser for any unauthorized actions 

carried out when beginning, developing or concluding the contract, if these actions were intentional or were due 

to gross negligence. Section 6 above shall apply in relation to the time-barring of claims made by the purchaser 

against the supplier’s managing director and his colleagues. 

8. If Putzmeister makes a claim for damages due to non-acceptance of the purchased item the sum of these damages 

shall amount to 15 % of the sales price of new appliances and 10 % of the sales price of used appliances unless 

damages amounting to a higher cost can be proven. The relevant Putzmeister trading partner shall be entitled 

to prove that the damage did not occur at all or that the damage was significantly lower than the amount given if 

necessary. 

IX. Safeguarding 

1. The item delivered shall remain the property of the supplier until completion of payment of the price agreed and of 

all other payments necessary under the commercial relationship with the purchaser. If payment of the sales price 

justifies that the supplier has a liability in the form of bills of exchange the proprietorial rights shall not be affected 

until the purchaser has completely redeemed all the bills of exchange. 

2. The purchaser shall transfer payments due from the resale of the item delivered as well all additional rights to the 

purchaser and these payments shall match the value of the item delivered. The purchaser shall be entitled to collect 

these debts. The supplier’s authority to also collect debts owed to them shall remain unaffected. 

3. The supplier is obliged to release securities at their own choice, provided that the achievable value of the securities 

exceeds the sum of the payments due under the commercial transaction by more than 10 %. 

4. Provided that the purchaser fulfils his obligations towards the supplier, the purchaser is entitled to possess the 

item delivered within the normal commercial process and within the terms of conditional sale, as long as the 

payments set out in section 2 have physically been transferred to the supplier. Extraordinary forms of ownership 

such as deposits, appropriation of securities and other transferrals are not permitted. Third party claims to the 

item delivered or to the payments transferred, in particular for deposits, must be notified to the supplier in writing 

immediately. 

5. During the conditional sale, the purchaser is wholly entitled to possess the item delivered and to use it as designated. 

If the purchaser breaches the contract - particularly if the purchaser is behind in their payments - and in cases 

where section IV. 2 applies, the supplier can appropriate the item to be delivered and can proceed with collecting 

payments due to him from resale of the product. The purchaser shall then be obliged to submit the item to the 

supplier - except if the purchaser’s rights to retain the item apply. All costs of retrieving the item and costs arising 

from its depreciation in value shall be borne by the purchaser. The supplier shall be entitled to sell the item on 

tender. On request, the purchaser must immediately provide the supplier with a list of surrendered claims as per 

Section 2 and with all other information and documentation necessary for the assertion of the supplier’s rights and 

must indicate this act of transfer to any debtors. 

6. The purchaser shall keep the delivered item in good condition during the conditional sale and ensure that all the 

maintenance and servicing works specified by the supplier are carried out by the supplier or a workshop approved 

by the supplier immediately - except in emergencies. 

7. For truck-mounted concrete pumps, the supplier has the right to ownership of the vehicle registration certificates 

during the period of conditional sale. 

8. Enforceability of the conditional sale and also seizure of the item supplied by the supplier are not considered to be 

a rescission of the contract. 

9. If the condition sale or transfer is not enforceable in law in the country where the goods are located then the security 

which proceeded the conditional sale or the transfer in this country shall be considered as binding. If the purchaser’s 

co-operation is necessary in this case, the purchaser must then implement all legal processes required to 

justify and to obtain such rights. 

74 

X. Intellectual property 

If the supplier must produce according to drawings or models, samples or using components supplied by the purchaser, 

then the purchase shall commit to ensuring that third property rights are not breached. The purchaser shall 

absolve the supplier from all claims from third parties relating to breach of property rights and shall reimburse the 

supplier for damages payouts, and the costs and expenses incurred. If the purchaser is not allowed to produce or 

deliver due to exercising of property rights by a third party, the supplier is entitled to terminate the work without closer 

scrutiny of their legal position. In this case, the supplier can withdraw from the contract and demand compensation 

for the damage as well as the costs and expenditure occurred. 

XI. Software usage 

If software is included in the goods supplied, the purchaser shall be granted a non-exclusive right to use the software 

supplied together with the documentation. The software shall be left for using on the specified item supplied. Using 

the software on more than one system is forbidden. 

The purchaser may only reproduce, revise, translate the software or convert it from object into source coding within 

the legally permitted scope (§§ 69 a ff. German Copyright Act). The purchaser is obliged not to remove manufacturer’s 

information - particularly copyright qualifiers -and not to change them without first obtaining express agreement of 

the supplier. 

All other rights relating to software and documentation including copies thereof shall remain with the supplier or with 

the software supplier. The issuing of sub-licenses is not permitted. 

XII. Law of jurisdiction, place of jurisdiction, court of jurisdiction 

1. The law in force in the Federal Republic of Germany shall apply exclusively. In cases of doubt, the Germanlanguage 

version of all contractual provisions shall take precedence. The harmonized purchasing legislation 

shall not apply. 

2. The place of execution shall be 72629 Aichtal. 

3. If the purchaser is a trader, a public law professional or a government special asset, Stuttgart shall be the place of 

jurisdiction for all disputes arising from this contractual relationship, including those relating to how the relationship 

arose and those relating to its enforceability and for complaints relating to bills of exchange and to cheques. 

The supplier can telephone any other competent court in accordance with the legal regulations. 

4. If one of the provisions in these conditions of sale and delivery is partially or totally invalid, the enforceability of 

the above conditions shall not be affected. 


D-72629 Aichtal · Postbox 2152 

Tel. +49 (0) 7127 599-0 · Fax +49 (0) 7127 599-520 

Internet www.moertelmaschinen.de · e-mail mm@putzmeister.de


Max-Eyth-Straße 10 · D-72631 Aichtal 

P. O. Box 2152 · D-72629 Aichtal 

Telefon +49 (0) 71 27 599-0 

Telefax +49 (0) 71 27 599-743 

Internet www.mortarmachines.com 

E-Mail mm@putzmeister.de 

MM 2599/12 GB 

The picture shows some of the special accessories · Subject to technical changes, errors and alterations Technical data may be changed without prior notice. · For safe and correct operation 

of the machine, please refer to the appropriate operating manual. · © 2012 by Putzmeister Mörtelmaschinen GmbH · All rights reserved

Catalogue 2012/2013 - Putzmeister MÃ¶rtelmaschinen GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?