LCD TV SERVICE MANUAL - Jordans Manuals

LCD TV
SERVICE MANUAL
CHASSIS : LB01B
MODEL : 42LD450/460 42LD450/460-TA
MODEL : 42LD461C 42LD461C-TA
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
P/NO : MFL62865307 (1007-REV01)
Internal Use Only
North/Latin America http://aic.lgservice.com
Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com
Printed in Korea

Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
CONTENTS
CONTENTS .............................................................................................. 2
PRODUCT SAFETY ................................................................................. 3
SPECIFICATION ....................................................................................... 6
ADJUSTMENT INSTRUCTION ................................................................ 9
BLOCK DIAGRAM...................................................................................15
EXPLODED VIEW .................................................................................. 16
SVC. SHEET ...............................................................................................
- 2 -
LGE Internal Use Only

Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1 W), keep the resistor 10 mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1 MΩ and 5.2 MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
IMPORTANT SAFETY NOTICE
- 3 -
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5 mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
To Instrument's
exposed
METALLIC PARTS
AC Volt-meter
0.15 uF
1.5 Kohm/10W
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
When 25A is impressed between Earth and 2nd Ground
for 1 second, Resistance must be less than 0.1 Ω
*Base on Adjustment standard
LGE Internal Use Only

CAUTION: Before servicing receivers covered by this service
manual and its supplements and addenda, read and follow the
SAFETY PRECAUTIONS on page 3 of this publication.
NOTE: If unforeseen circumstances create conflict between the
following servicing precautions and any of the safety precautions on
page 3 of this publication, always follow the safety precautions.
Remember: Safety First.
General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC power
source before;
a. Removing or reinstalling any component, circuit board
module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical plug or
other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect polarity
installation of electrolytic capacitors may result in an
explosion hazard.
2. Test high voltage only by measuring it with an appropriate high
voltage meter or other voltage measuring device (DVM,
FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
3. Do not spray chemicals on or near this receiver or any of its
assemblies.
4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable
non-abrasive applicator; 10 % (by volume) Acetone and 90 %
(by volume) isopropyl alcohol (90 % - 99 % strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication of
contacts in not required.
5. Do not defeat any plug/socket B+ voltage interlocks with which
receivers covered by this service manual might be equipped.
6. Do not apply AC power to this instrument and/or any of its
electrical assemblies unless all solid-state device heat sinks are
correctly installed.
7. Always connect the test receiver ground lead to the receiver
chassis ground before connecting the test receiver positive
lead.
Always remove the test receiver ground lead last.
8. Use with this receiver only the test fixtures specified in this
service manual.
CAUTION: Do not connect the test fixture ground strap to any
heat sink in this receiver.
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid-state) devices can be damaged easily
by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES
devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques
should be used to help reduce the incidence of component
damage caused by static by static electricity.
1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any electrostatic
charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the
unit under test.
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
SERVICING PRECAUTIONS
- 4 -
2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES
devices.
4. Use only an anti-static type solder removal device. Some solder
removal devices not classified as "anti-static" can generate
electrical charges sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate
electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective
package until immediately before you are ready to install it.
(Most replacement ES devices are packaged with leads
electrically shorted together by conductive foam, aluminum foil
or comparable conductive material).
7. Immediately before removing the protective material from the
leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be
installed.
CAUTION: Be sure no power is applied to the chassis or circuit,
and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged
replacement ES devices. (Otherwise harmless motion such as
the brushing together of your clothes fabric or the lifting of your
foot from a carpeted floor can generate static electricity
sufficient to damage an ES device.)
General Soldering Guidelines
1. Use a grounded-tip, low-wattage soldering iron and appropriate
tip size and shape that will maintain tip temperature within the
range or 500 °F to 600 °F.
2. Use an appropriate gauge of RMA resin-core solder composed
of 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean and well tinned.
4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle
(0.5 inch, or 1.25 cm) brush with a metal handle.
Do not use freon-propelled spray-on cleaners.
5. Use the following unsoldering technique
a. Allow the soldering iron tip to reach normal temperature.
(500 °F to 600 °F)
b. Heat the component lead until the solder melts.
c. Quickly draw the melted solder with an anti-static, suctiontype
solder removal device or with solder braid.
CAUTION: Work quickly to avoid overheating the circuit
board printed foil.
6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
(500 °F to 600 °F)
b. First, hold the soldering iron tip and solder the strand against
the component lead until the solder melts.
c. Quickly move the soldering iron tip to the junction of the
component lead and the printed circuit foil, and hold it there
only until the solder flows onto and around both the
component lead and the foil.
CAUTION: Work quickly to avoid overheating the circuit
board printed foil.
d. Closely inspect the solder area and remove any excess or
splashed solder with a small wire-bristle brush.
LGE Internal Use Only

IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong) through
which the IC leads are inserted and then bent flat against the
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique
as outlined in paragraphs 5 and 6 above.
Removal
1. Desolder and straighten each IC lead in one operation by gently
prying up on the lead with the soldering iron tip as the solder
melts.
2. Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing the
IC.
Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and
solder it.
3. Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1. Remove the defective transistor by clipping its leads as close as
possible to the component body.
2. Bend into a "U" shape the end of each of three leads remaining
on the circuit board.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder
each connection.
Power Output, Transistor Device
Removal/Replacement
1. Heat and remove all solder from around the transistor leads.
2. Remove the heat sink mounting screw (if so equipped).
3. Carefully remove the transistor from the heat sink of the circuit
board.
4. Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6. Replace heat sink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 5 -
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
following guidelines and procedures should be followed whenever
this condition is encountered.
At IC Connections
To repair a defective copper pattern at IC connections use the
following procedure to install a jumper wire on the copper pattern
side of the circuit board. (Use this technique only on IC
connections).
1. Carefully remove the damaged copper pattern with a sharp
knife. (Remove only as much copper as absolutely necessary).
2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
carefully crimp it around the IC pin. Solder the IC connection.
4. Route the jumper wire along the path of the out-away copper
pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
excess jumper wire.
At Other Connections
Use the following technique to repair the defective copper pattern
at connections other than IC Pins. This technique involves the
installation of a jumper wire on the component side of the circuit
board.
1. Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.
2. Trace along the copper pattern from both sides of the pattern
break and locate the nearest component that is directly
connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead of the
nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is dressed so the
it does not touch components or sharp edges.
LGE Internal Use Only

SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This specification is applied to the LCD TV used LB01B
chassis.
2. Requirement for Test
Each part is tested as below without special appointment.
1) Temperature
: 25 ºC ± 5 ºC (77 ºF ± 9 ºF), CST : 40 ºC ± 5 ºC
2) Relative Humidity : 65 % ± 10 %
3) Power Voltage
: Standard input voltage (AC 100-240 V~ 50 / 60 Hz)
* Standard Voltage of each products is marked by models.
4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
5) The receiver must be operated for about 5 minutes prior to
the adjustment.
5. Module optical specifications
(1) LGD Module
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 6 -
3. Test method
1) Performance: LGE TV test method followed
2) Demanded other specification
- Safety: CE, IEC specification
- EMC:CE, IEC
No. Item Specification Min. Typ. Max. Remark
1. Viewing Angle (CR > 10) Right/Left/Up/Down 178 Degree
2. Luminance Luminance (cd/m2 ) 400 500
Variation - 1.3 MAX / MIN
3. Contrast Ratio CR 1100 1500
4. CIE Color Coordinates White Wx 0.279
Wy 0.292
RED Rx 0.636
Ry Typ. 0.335 Typ.
Green Gx -0.03 0.291 +0.03
Gy 0.603
Blue Bx 0.146
By 0.061
1) Standard Test Condition (The unit has been ‘ON’)
2) Stable for approximately 30 minutes in a dark environment at 25 ºC ± 2 ºC.
3) The values specified are at approximate distance 50 cm from the LCD surface.
4) Ta = 25 ºC ± 2 °C, VLCD = 12.0 V, fv = 60 Hz, Dclk = 74.25 MHz, VBR_A = 1.65 V, EXTVBR-B = 100 %
LGE Internal Use Only

6. Component Video Input (Y, CB/PB, CR/PR)
No.
Resolution
Specification
H-freq(kHz) V-freq(Hz)
1. 720x480 15.73 60.00 SDTV,DVD 480i
2. 720x480 15.63 59.94 SDTV,DVD 480i
3. 720x480 31.47 59.94 480p
4. 720x480 31.50 60.00 480p
5. 720x576 15.625 50.00 SDTV,DVD 625 Line
6. 720x576 31.25 50.00 HDTV 576p
7. 1280x720 45.00 50.00 HDTV 720p
8. 1280x720 44.96 59.94 HDTV 720p
9. 1280x720 45.00 60.00 HDTV 720p
10. 1920x1080 31.25 50.00 HDTV 1080i
11. 1920x1080 33.75 60.00 HDTV 1080i
12. 1920x1080 33.72 59.94 HDTV 1080i
13. 1920x1080 56.250 50 HDTV 1080p
14. 1920x1080 67.5 60 HDTV 1080p
7. RGB (PC)
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 7 -
Remark
No.
Resolution
Specification
H-freq(kHz) V-freq(Hz) Pixel Clock(MHz)
Proposed Remark
1. 720*400 31.468 70.08 28.321 For only DOS mode
2. 640*480 31.469 59.94 25.17 VESA Input 848*480 60 Hz, 852*480 60 Hz
-> 640*480 60 Hz Display
3. 800*600 37.879 60.31 40.00 VESA
4. 1024*768 48.363 60.00 65.00 VESA(XGA)
5. 1280*768 47.78 59.87 79.5 WXGA
6. 1360*768 47.72 59.8 84.75 WXGA
7. 1280*1024 63.981 60.02 108.875 SXGA FHD Model
8. 1920*1080 66.587 59.93 138.625 WUXGA FHD model
LGE Internal Use Only

8. HDMI Input
(1) DTV Mode
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark
1. 720*480 31.469 /31.5 59.94 /60 27.00/27.03 SDTV 480P
2. 720*576 31.25 50 54 SDTV 576P
3. 1280*720 37.500 50 74.25 HDTV 720P
4. 1280*720 44.96 /45 59.94 /60 74.17/74.25 HDTV 720P
5. 1920*1080 33.72 /33.75 59.94 /60 74.17/74.25 HDTV 1080I
6. 1920*1080 28.125 50.00 74.25 HDTV 1080I
7. 1920*1080 26.97 /27 23.97 /24 74.17/74.25 HDTV 1080P
8. 1920*1080 33.716 /33.75 29.976 /30.00 74.25 HDTV 1080P
9. 1920*1080 56.250 50 148.5 HDTV 1080P
10. 1920*1080 67.43 /67.5 59.94 /60 148.35/148.50 HDTV 1080P
(2) PC Mode
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark
1. 720*400 31.468 70.08 28.321 HDCP
2. 640*480 31.469 59.94 25.17 VESA HDCP
3. 800*600 37.879 60.31 40.00 VESA HDCP
4. 1024*768 48.363 60.00 65.00 VESA(XGA) HDCP
5. 1280*768 47.78 59.87 79.5 WXGA HDCP
6. 1360*768 47.72 59.8 84.75 WXGA HDCP
7. 1280*1024 63.981 60.02 108.875 SXGA HDCP/FHD model
8. 1920*1080 67.5 60.00 138.625 WUXGA HDCP/FHD model
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 8 -
LGE Internal Use Only

1. Application Range
This specification sheet is applied to all of the LCD TV with
LB01B chassis.
2. Designation
1) The adjustment is according to the order which is
designated and which must be followed, according to the
plan which can be changed only on agreeing.
2) Power Adjustment: Free Voltage
3) Magnetic Field Condition: Nil.
4) Input signal Unit: Product Specification Standard
5) Reserve after operation: Above 5 Minutes (Heat Run)
Temperature : at 25 ºC ± 5 ºC
Relative humidity : 65 % ± 10 %
Input voltage : 220 V, 60 Hz
6) Adjustment equipments: Color Analyzer(CA-210 or CA-110),
DDC Adjustment Jig equipment, Service remote control.
7) Push the “IN STOP” key - For memory initialization.
Case1 : Software version up
1. After downloading S/W by USB, TV set will reboot
automatically
2. Push “In-stop” key
3. Push “Power on” key
4. Function inspection
5. After function inspection, Push “In-stop” key.
Case2 : Function check at the assembly line
1. When TV set is entering on the assembly line, Push
“In-stop” key at first.
2. Push “Power on” key for turning it on.
-> If you push “Power on” key, TV set will recover
channel information by itself.
3. After function inspection, Push “In-stop” key.
3. Main PCB check process
* APC - After Manual-Insult, executing APC
* Boot file Download
1) Execute ISP program “Mstar ISP Utility” and then click
“Config” tab.
(1)
filexxx.bin
2) Set as below, and then click “Auto Detect” and check “OK”
message
If “Error” is displayed, Check connection between
computer, jig, and set.
3) Click “Read” tab, and then load download file (XXXX.bin)
by clicking “Read”
4) Click “Connect” tab. If “Can’t” is displayed, check
connection between computer, jig, and set.
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
ADJUSTMENT INSTRUCTION
- 9 -
5) Click “Auto” tab and set as below
6) Click “Run”.
7) After downloading, check “OK” message.
(4)
filexxx.bin
(7) ……….OK
* USB DOWNLOAD
1) Put the USB Stick to the USB socket
2) Automatically detecting update file in USB Stick
- If your downloaded program version in USB Stick is Low,
it didn’t work. But your downloaded version is High, USB
data is automatically detecting
3) Show the message “Copying files from memory”
(5)
(6)
(2) (3)
Please Check the Speed :
To use speed between
from 200KHz to 400KHz
LGE Internal Use Only

4) Updating is staring.
5) Uploading completed, The TV will restart automatically.
6) If your TV is turned on, check your updated version and
Tool option.(explain the Tool option, next stage)
* If downloading version is more high than your TV have,
TV can lost all channel data. In this case, you have to
channel recover. if all channel data is cleared, you didn’t
have a DTV/ATV test on production line.
* After downloading, have to adjust Tool Option again.
1) Push "IN-START" key in service remote control.
2) Select “Tool Option 1” and Push “OK” button.
3) Punch in the number. (Each model has their number)
Module Tool option1 Tool option2 Tool option3 Tool option4 Tool option5
LGD 25313 10770 52228 26892 32
CMO 25317 10770 52228 26892 32
4) Completed selecting Tool option.
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 10 -
3.1. ADC Process
(1) ADC
- Enter Service Mode by pushing “ADJ” key,
- Enter Internal ADC mode by pushing “ G ” key at “5. ADC
Calibration”
Using ‘power on’ button of the Adjustment R/C,
power on TV.
* ADC Calibration Protocol (RS232)
No Item CMD1 CMD2 Data0
Enter Adjust Adjust A A 0 0 When transfer the ‘Mode In’,
Mode ‘Mode In’ Carry the command.
ADC adjust ADC Adjust A D 1 0 Automatically adjustment
(The use of a internal pattern)
Adjust Sequence
• aa 00 00 [Enter Adjust Mode]
• xb 00 40 [Component1 Input (480i)]
• ad 00 10 [Adjust 480i Comp1]
• xb 00 60 [RGB Input (1024*768)]
• ad 00 10 [Adjust 1024*768 RGB]
• aa 00 90 End Adjust mode
* Required equipment : Adjustment R/C.
3.2. Function Check
* Check display and sound
- Check Input and Signal items. (cf. work instructions)
1) TV
2) AV (SCART1/SCART2/ CVBS)
3) COMPONENT (480i)
4) RGB (PC : 1024 x 768 @ 60 Hz)
5) HDMI
6) PC Audio In
* Display and Sound check is executed by Remote control.
LGE Internal Use Only

4. Total Assembly line process
4.1. Adjustment Preparation
· W/B Equipment condition
CA210 : CH 9, Test signal : Inner pattern (85IRE)
· Above 5 minutes H/run in the inner pattern. (“power on” key
of adjust remote control)
Cool 13,000 K X=0.269(±0.002)
Y=0.273(±0.002)
Medium 9,300 K X=0.285(±0.002) Inner pattern
Y=0.293(±0.002) (216gray,85IRE)
Warm 6,500 K X=0.313(±0.002)
Y=0.329(±0.002)
* Connecting picture of the measuring instrument
(On Automatic control)
Inside PATTERN is used when W/B is controlled. Connect to
auto controller or push Adjustment R/C POWER ON ->
Enter the mode of White-Balance, the pattern will come out.
Full White Pattern
RS-232C Communication
* Auto-control interface and directions
1) Adjust in the place where the influx of light like floodlight
around is blocked. (illumination is less than 10 lux).
2) Adhere closely the Color Analyzer (CA210) to the module
less than 10 cm distance, keep it with the surface of the
Module and Color Analyzer’s prove vertically.(80° ~ 100°).
3) Aging time
- After aging start, keep the power on (no suspension of
power supply) and heat-run over 5 minutes.
- Using ‘no signal’ or ‘full white pattern’ or the others,
check the back light on.
• Auto adjustment Map(RS-232C)
RS-232C COMMAND
[CMD ID DATA]
Wb 00 00 White Balance Start
Wb 00 ff White Balance End
COLOR
ANALYZER
TYPE: CA-210
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
CA-210
RS-232C COMMAND MIN CENTER MAX
[CMD ID DATA] (DEFAULT)
Cool Mid Warm Cool Mid Warm
R Gain jg Ja jd 00 172 192 192 192
G Gain jh Jb je 00 172 192 192 192
B Gain ji Jc jf 00 192 192 172 192
R Cut 64 64 64 128
G Cut 64 64 64 128
B Cut 64 64 64 128
- 11 -
Color Temperature : COOL, Medium, Warm.
One of R Gain/G Gain/ B Gain should be kept on 0xC0, and
adjust other two lower than C0.
(when R/G/B Gain are all C0, it is the FULL Dynamic Range
of Module)
* Manual W/B process using adjusts Remote control.
• After enter Service Mode by pushing “ADJ” key,
• Enter White Balance by pushing “G” key at “6. White
Balance”.
* After done all adjustments, Press “In-start” button and
compare Tool option and Area option value with its BOM, if
it is correctly same then unplug the AC cable. If it is not
same, then correct it same with BOM and unplug AC cable.
For correct it to the model’s module from factory Jig model.
* Push the “IN STOP” key after completing the function
inspection. And Mechanical Power Switch must be set
“ON”.
4.2. DDC EDID Write (RGB 128Byte )
• Connect D-sub Signal Cable to D-sub Jack.
• Write EDID Data to EEPROM(24C02) by using DDC2B
protocol.
• Check whether written EDID data is correct or not.
* For SVC main Assembly, EDID have to be downloaded to
Insert Process in advance.
4.3. DDC EDID Write (HDMI 256Byte)
• Connect HDMI Signal Cable to HDMI Jack.
• Write EDID Data to EEPROM(24C02) by using DDC2B
protocol.
• Check whether written EDID data is correct or not.
* For SVC main Assembly, EDID have to be downloaded to
Insert Process in advance.
4.4. EDID DATA
1) All Data : HEXA Value
2) Changeable Data :
*: Serial No : Controlled / Data:01
**: Month : Controlled / Data:00
***:Year : Controlled
****:Check sum
LGE Internal Use Only

4.5. V-COM Adjust(Only LGD(M+S) Module)
- Why need Vcom adjustment?
A The Vcom (Common Voltage) is a Reference Voltage of
Liquid Crystal Driving.
-> Liquid Crystal need for Polarity Change with every frame.
S
Y
S
T
E
M
V COM
Da t a I n p u t
Power Po w er Input I n p u t
Data (R,G,B ) &
Control si gnal
Ti m in g
Co nt r o ll er
In t er f ace
Po w er
Blo ck
V COM
Data (R,G,B) & C ontro l s ignal
Control si gnal
Column Line
V COM
Row Line TFT
CLC CST
- Adjust sequence
· Press the PIP key of th ADJ remote control.(This PIP key is
hot key to enter the VCOM adjusting mode)
(Or After enter Service Mode by pushing “ADJ” key, then
Enter V-Com Adjust mode by pushing “G” key at “10. V-
Com”
· As pushing the right or the left key on the remote control,
and find the V-COM value which is no or minimized the
Flicker. (If there is no flicker at default value, Press the exit
key and finish the VCOM adjustment.)
· Push the “OK” key to store value. Then the message
“Saving OK” is pop.
· Press the exit key to finish VCOM adjustment.
(Visual Adjust and control the Voltage level)
4.6. Outgoing condition Configuration
- When pressing IN-STOP key by SVC remocon, Red LED are
blinked alternatively. And then Automatically turn off.
(Must not AC power OFF during blinking)
4.7. Internal pressure
Confirm whether is normal or not when between power
board’s ac block and GND is impacted on 1.5 kV(dc) or 2.2
kV(dc) for one second.
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
Gat e Driv e IC
So urce D r iv e I C
Circuit Block
Gamma
Re f er ence V o ltage
Gamm a Reference
Volta ge
Panel
Liquid
Crystal
- 13 -
5. Model name & Serial number D/L
• Press “Power on” key of service remocon.
(Baud rate : 115200 bps)
• Connect RS232 Signal Cable to RS-232 Jack.
• Write Serial number by use RS-232.
• Must check the serial number at the Diagnostics of SET UP
menu. (Refer to below).
5.1. Signal TABLE
CMD LENGTH ADH ADL DATA_1 . . . Data_n CS DELAY
CMD : A0h
LENGTH : 85~94h (1~16 bytes)
ADH : EEPROM Sub Address high (00~1F)
ADL : EEPROM Sub Address low (00~FF)
Data : Write data
CS : CMD + LENGTH + ADH + ADL + Data_1 +…+ Data_n
Delay : 20ms
5.2. Command Set
No. Adjust mode CMD(hex) LENGTH(hex) Description
1 EEPROM WRITE A0h 84h+n n-bytes Write (n = 1~16)
* Description
FOS Default write : write
Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0,
Phase
Data write : Model Name and Serial Number write in
EEPROM,.
5.3. Method & notice
A. Serial number D/L is using of scan equipment.
B. Setting of scan equipment operated by Manufacturing
Technology Group.
C. Serial number D/L must be conformed when it is produced
in production line, because serial number D/L is mandatory
by D-book 4.0.
* Manual Download (Model Name and Serial Number)
If the TV set is downloaded by OTA or Service man, Sometimes
model name or serial number is initialized.(Not always)
There is impossible to download by bar code scan, so It need
Manual download.
1) Press the ‘instart’ key of ADJ remote controller.
2) Go to the menu ‘5.Model Number D/L’ like below photo.
3) Input the Factory model name(ex 42LD450-ZA) or Serial
number like photo.
LGE Internal Use Only

4) Check the model name Instart menu -> Factory name
displayed (ex 42LD450-ZA)
5) Check the Diagnostics (DTV country only) -> Buyer model
displayed (ex 42LD450)
6. CI+ key download(Only for CI model)
6-1. Download Procedure
(1) Press "Power on" button of a service R/C.(Baud rate :
115200 bps)
(2) Connect RS232-C Signal Cable.
(3) Write CI+ Key through RS-232-C.
(4) Check whether the key was downloaded or not at ‘In Start’
menu. (Refer to below).
=> Check the Download to CI+ Key value in LGset.
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 14 -
6-2. check the method of CI+ Key value
(1) Check the method on Instart menu
(2) check the method of RS232C Command
1) into the main ass’y mode (RS232 : aa 00 00)
CMD 1 CMD 2 Data 0
A A 0 0
2) check the key download for transmitted command
(RS232 : ci 00 10)
CMD 1 CMD 2 Data 0
C I 1 0
3) result value
- normally status for download : OKx
- abnormally status for download : NGx
6-3. Check the method of CI+ key value (RS232)
(1) into the main ass’y mode (RS232 : aa 00 00)
CMD 1 CMD 2 Data 0
A A 0 0
(2) Check the method of CI+ key by command
(RS232 : ci 00 20)
CMD 1 CMD 2 Data 0
C I 2 0
(3) Result value
i 01 OK 1d1852d21c1ed5dcx
CI+ key Value
LGE Internal Use Only

Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
BLOCK DIAGRAM
- 15 -
LGE Internal Use Only

LV1 LV2
300
400
800
200
521
540
Copyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
EXPLODED VIEW
500
530
- 16 -
810
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
120
910
A10
A5
A4
A2
A21
900
510
LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
PCM_A[8]
CI_TS_DATA[6]
PCM_A[3]
PCM_A[10]
FE_TS_DATA[5]
PCM_A[0]
PCM_D[6]
CI_TS_DATA[0]
PCM_D[2]
PCM_A[7]
PCM_A[9]
FE_TS_DATA[3]
PCM_A[12]
PCM_A[4]
PCM_D[5]
CI_TS_DATA[3]
PCM_A[5]
FE_TS_DATA[0]
CI_TS_DATA[5]
PCM_A[2]
PCM_A[13]
FE_TS_DATA[4]
PCM_A[1]
PCM_A[3]
PCM_A[2]
CI_TS_DATA[4]
PCM_D[1]
PCM_A[11]
FE_TS_DATA[2]
PCM_D[4]
PCM_A[7]
PCM_A[6]
PCM_A[0]
CI_TS_DATA[7]
PCM_A[4]
PCM_D[0]
FE_TS_DATA[6]
CI_TS_DATA[1]
CI_TS_DATA[2]
PCM_A[6]
PCM_A[14]
PCM_D[3]
PCM_D[7]
FE_TS_DATA[1]
FE_TS_DATA[7]
PCM_A[5]
PCM_A[1]
MODEL_OPT_2
/PCM_WE
R104
10K
OPT
HP_DET
S7_RXD
I2C_SDA
SPI_SDI
FRC_RESET
+3.3V_Normal
I2C_SDA
/PF_OE
PCM_A[0-7]
+3.5V_ST
C104
8pF
OPT
C108
0.1uF
OPT
IC103
CAT24WC08W-T
3
A2
2
A1
4
VSS
1
A0
5 SDA
6 SCL
7 WP
8 VCC
TUNER_RESET
FRC_PWM1
CI_TS_DATA[0-7]
R158 100
OPT
M_REMOTE_RX
R105
1K
OPT
UART_FRC_TX
R1081K
OPT
DEMOD_RESET
PCM_D[0-7]
R126
1K
PF_ALE
PF_ALE
SPI_SCK
IC102
HY27UF082G2B-TPCB
2GBIT
26
NC_17
27
NC_18
28
NC_19
29
I/O0
30
I/O1
31
I/O2
32
I/O3
33
NC_20
34
NC_21
35
NC_22
36
VSS_2
37
VCC_2
38
NC_23
39
NC_24
40
NC_25
41
I/O4
42
I/O5
43
I/O6
44
I/O7
45
NC_26
46
NC_27
47
NC_28
48
NC_29
17
ALE
3
NC_3
6
NC_6
16
CLE
15
NC_10
14
NC_9
13
VSS_1
12
VCC_1
11
NC_8
10
NC_7
9
CE
8
RE
7
R/B
4
NC_4
5
NC_5
25
NC_16
24
NC_15
23
NC_14
2
NC_2
22
NC_13
21
NC_12
1
NC_1
20
NC_11
19
WP
18
WE
/PCM_WAIT
R125
1K
OPT
DSUB_DET
R113
4.7K
M_REMOTE_TX
USB1_OCD
/PF_WE
FE_TS_VAL_ERR
R115
1K
ERROR_OUT
R134 22
R159 100
OPT
CI_TS_SYNC
SC1/COMP1_DET
A_DIM
/PCM_REG
FE_TS_SYNC
PCM_5V_CTL
S7_TXD
5V_DET_HDMI_4
R128
22
+3.3V_Normal
/PCM_IRQA
+5V_Normal
/PF_OE
C111
2.2uF
FRC_SCL
R118
1K OPT
SC_RE1
/PCM_IOWR
R103
0
SCAN_BLK1/OPC_OUT
/PF_CE1
SPI_SDO
C107
0.1uF
R149
22
M_REMOTE
/PCM_IORD
5V_DET_HDMI_3
PWM2
C105
0.1uF
C103
0.1uF
/PF_WE
R135 22
I2C_SDA
5V_DET_HDMI_2
ET_RXER
R124
1K
MODEL_OPT_3
R120
1K
OPT
C106
8pF
OPT
FRC_PWM0
R123
1K
OPT
R146
33
/PF_CE1
/PF_CE0
R101
3.3K
OPT
AV_CVBS_DET
RGB_DDC_SDA
PWM0
MODEL_OPT_1
I2C_SCL
R148
22 M_REMOTE
CI_TS_VAL
PCM_A[0-14]
R133
10K
I2C_SCL
/F_RB
/RST_PHY
R155
0
OPT
PWM_DIM
/PCM_OE
UART_FRC_RX
Q101
KRC103S
OPT
E
B
C
R106
1K
R138 22
FE_TS_DATA[0-7]
PCM_RST
R117
1K
/PF_WP
I2C_SCL
SCAN_BLK2
SC_RE2
R116
1K OPT
+3.3V_Normal
R107 1K
R157 100
R132
10K
R137 22
CI_TS_CLK
SIDEAV_DET
/PF_CE0
IC102-*1
HY27US08121B-TPCB
512MBIT
26
NC_17
27
NC_18
28
NC_19
29
I/O0
30
I/O1
31
I/O2
32
I/O3
33
NC_20
34
NC_21
35
NC_22
36
VSS_2
37
VCC_2
38
PRE
39
NC_23
40
NC_24
41
I/O4
42
I/O5
43
I/O6
44
I/O7
45
NC_25
46
NC_26
47
NC_27
48
NC_28
17
ALE
3
NC_3
6
NC_6
16
CLE
15
NC_10
14
NC_9
13
VSS_1
12
VCC_1
11
NC_8
10
NC_7
9
CE
8
RE
7
R/B
4
NC_4
5
NC_5
25
NC_16
24
NC_15
23
NC_14
2
NC_2
22
NC_13
21
NC_12
1
NC_1
20
NC_11
19
WP
18
WE
/PCM_CD
/F_RB
C101
0.1uF
R139 22
5V_DET_HDMI_1
/SPI_CS
/PCM_CE
/PF_WP
R109 3.9K
C109
0.1uF
R127 4.7K
+3.3V_Normal
USB1_CTL
MODEL_OPT_0
PWM0
FRC_SDA
R129 22
PWM1
+3.3V_Normal
PWM2
WIRELESS_DL_RX
R136 22
RGB_DDC_SCL
WIRELESS_DL_TX
R121
1K
FE_TS_CLK
R102
3.3K
R147
33
R151
33
PWM0
PWM1
AUD_LRCH
AUD_MASTER_CLK
AUD_SCK
+3.3V_Normal
R111 22
R112 22
R156 10K
/FLASH_WP
/RST_HUB
C102
10uF
P3903
12505WS-03A00
URSA_DEBUG
1
2
3
4
P3904
12505WS-03A00
URSA_DEBUG
1
2
3
4
NEC_SDA
I2C_SDA
I2C_SCL
AMP_SCL
R142
3.3K
R145
2.2K
R143
3.3K
R144
2.2K
AMP_SDA
+3.3V_Normal
NEC_SCL
CONTROL_ATTEN
R160
1K
/PIF_SPI_CS
IC104
M24M01-HRMN6TP
3
E2
2
E1
4
VSS
1
NC
5
SDA
6
SCL
7
WP
8
VCC
AR104
22
AR103
22
AR101
22
AR102
22
R141
1K
R140
1K
R110
0
R150
0
MODEL_OPT_6
IC102-*2
NAND01GW3B2CN6E
1GBIT
26
NC_17
27
NC_18
28
NC_19
29
I/O0
30
I/O1
31
I/O2
32
I/O3
33
NC_20
34
NC_21
35
NC_22
36
VSS_2
37
VDD_2
38
NC_23
39
NC_24
40
NC_25
41
I/O4
42
I/O5
43
I/O6
44
I/O7
45
NC_26
46
NC_27
47
NC_28
48
NC_29
17
AL
3
NC_3
6
NC_6
16
CL
15
NC_10
14
NC_9
13
VSS_1
12
VDD_1
11
NC_8
10
NC_7
9
E
8
R
7
RB
4
NC_4
5
NC_5
25
NC_16
24
NC_15
23
NC_14
2
NC_2
22
NC_13
21
NC_12
1
NC_1
20
NC_11
19
WP
18
W
LGE107D (S7M Divx_Non RM)
IC101
S7M_DIVX & MS10
PCM_D0
U22
PCM_D1
T21
PCM_D2
T22
PCM_D3
AB18
PCM_D4
AC18
PCM_D5
AC19
PCM_D6
AC20
PCM_D7
AC21
PCM_A0
U21
PCM_A1
V21
PCM_A2
Y22
PCM_A3
AA22
PCM_A4
R22
PCM_A5
R21
PCM_A6
T23
PCM_A7
T24
PCM_A8
AA23
PCM_A9
Y20
PCM_A10
AB17
PCM_A11
AA21
PCM_A12
U23
PCM_A13
Y23
PCM_A14
W23
PCM_REG_N
W22
PCM_OE_N
AA17
PCM_WE_N
V22
PCM_IORD_N
W21
PCM_IOWR_N
Y21
PCM_CE_N
AA20
PCM_IRQA_N
V23
PCM_CD_N
P23
PCM_WAIT_N
R23
PCM_RESET
P22
PCM_PF_CE0Z
AC17
PCM_PF_CE1Z
AB20
PCM_PF_OEZ
AA18
PCM_PF_WEZ
AB21
PCM_PF_ALE
AB19
PCM_PF_AD[15]
AD17
PCM_PF_RBZ
AA19
UART_TX2/GPIO65
M23
UART_RX2/GPIO64
N23
DDCR_DA/GPIO71
M22
DDCR_CK/GPIO72
N22
DDCA_DA/UART0_TX
A5
DDCA_CK/UART0_RX
B5
PWM0/GPIO66
K23
PWM1/GPIO67
K22
PWM2/GPIO68
G23
PWM3/GPIO69
G22
PWM4/GPIO70
G21
SAR0/GPIO31
C6
SAR1/GPIO32
B6
SAR2/GPIO33
C8
SAR3/GPIO34
C7
SAR4/GPIO35
A6
GPIO143/TCON0
N21
GPIO145/TCON2
M21
GPIO147/TCON4
L22
GPIO149/TCON6
L21
GPIO151/TCON8
P21
GPIO36/UART3_RX
K21
GPIO37/UART3_TX
L23
GPIO38
K20
GPIO39
L20
GPIO40
M20
GPIO41
G20
GPIO42
G19
GPIO50/UART1_RX
F20
GPIO51/UART1_TX
F19
GPIO6/PM0/INT0
E7
GPIO7/PM1/PM_UART_TX
D7
GPIO8/PM2
E11
GPIO9/PM3
G9
GPIO10/PM4
F9
GPIO11/PM5/PM_UART_RX/INT1
C5
PM_SPI_CS1/GPIO12/PM6
E8
PM_SPI_WP1/GPIO13/PM7
E9
PM_SPI_WP2/GPIO14/PM8/INT2
F7
GPIO15/PM9
F6
PM_SPI_CS2/GPIO16/PM10
D8
GPIO17/PM11/INT3
G12
GPIO18/PM12/INT4
F10
PM_SPI_CK/GPIO1
D9
GPIO0/PM_SPI_CZ
D11
PM_SPI_DI/GPIO2
E10
PM_SPI_DO/GPIO3
D10
TS0_CLK
AA9
TS0_VLD
AA5
TS0_SYNC
AA10
TS0_D0
AB5
TS0_D1
AC4
TS0_D2
Y6
TS0_D3
AA6
TS0_D4
W6
TS0_D5
AA7
TS0_D6
Y9
TS0_D7
AA8
TS1_CLK
AC5
TS1_VLD
AC6
TS1_SYNC
AB6
TS1_D0
AC10
TS1_D1
AB10
TS1_D2
AC9
TS1_D3
AB9
TS1_D4
AC8
TS1_D5
AB8
TS1_D6
AC7
TS1_D7
AB7
MPIF_CLK
D12
MPIF_CS_N
D14
MPIF_BUSY
E14
MPIF_D0
E12
MPIF_D1
F12
MPIF_D2
D13
MPIF_D3
E13
LGE101D (S7 Non_Tcon/RM)
IC101-*8
S7_DIVX & MS10
NC_48
AE1
NC_78
AF16
NC_64
AF1
NC_50
AE3
NC_45
AD14
NC_34
AD3
NC_77
AF15
NC_65
AF2
NC_62
AE15
NC_33
AD2
NC_47
AD16
NC_46
AD15
NC_63
AE16
NC_66
AF3
NC_76
AF14
NC_32
AD1
NC_44
AD13
NC_61
AE14
NC_60
AE13
NC_51
AE4
NC_36
AD5
NC_67
AF4
NC_35
AD4
NC_49
AE2
NC_71
AF8
NC_40
AD9
NC_56
AE9
NC_72
AF9
NC_58
AE11
NC_69
AF6
NC_53
AE6
NC_74
AF11
NC_37
AD6
NC_43
AD12
NC_52
AE5
NC_75
AF12
NC_68
AF5
NC_59
AE12
NC_57
AE10
NC_70
AF7
NC_42
AD11
NC_38
AD7
NC_41
AD10
NC_54
AE7
NC_73
AF10
NC_39
AD8
NC_55
AE8
NC_12
Y11
GND_105
Y19
LVACLKP/LLV6P/BLUE[3]
W26
LVACLKN/LLV6N/BLUE[2]
W25
LVA0P/LLV3P/BLUE[9]
U26
LVA0N/LLV3N/BLUE[8]
U25
LVA1P/LLV4P/BLUE[7]
U24
LVA1N/LLV4N/BLUE[6]
V26
LVA2P/LLV5P/BLUE[5]
V25
LVA2N/LLV5N/BLUE[4]
V24
LVA3P/LLV7P/BLUE[1]
W24
LVA3N/LLV7N/BLUE[0]
Y26
LVA4P/LLV8P
Y25
LVA4N/LLV8N
Y24
LVBCLKP/LLV0P/GREEN[5]
AC26
LVBCLKN/LLV0N/GREEN[4]
AC25
LVB0P/RLV6P/RED[1]
AA26
LVB0N/RLV6N/RED[0]
AA25
LVB1P/RLV7P/GREEN[9]
AA24
LVB1N/RLV7N/GREEN[8]
AB26
LVB2P/RLV8P/GREEN[7]
AB25
LVB2N/RLV8N/GREEN[6]
AB24
LVB3P/LLV1P/GREEN[3]
AC24
LVB3N/LLV1N/GREEN[2]
AD26
LVB4P/LLV0P/GREEN[1]
AD25
LVB4N/LLV0N/GREEN[0]
AD24
RLV3P/RED[7]
AD23
RLV3N/RED[6]
AE23
RLV0P/LVSYNC
AE26
RLV0N/LHSYNC
AE25
RLV1N/LCK
AF26
RLV2P/RED[9]
AF25
RLV1P/LDE
AE24
RLV2N/RED[8]
AF24
RLV4P/RED[5]
AF23
RLV4N/RED[4]
AD22
RLV5P/RED[3]
AE22
RLV5N/RED[2]
AF22
TCON3/OE/GOE/GCLK2
AD19
TCON15/SCAN_BLK1
AE19
TCON18/CS7/GCLK5
AD21
TCON19/CS8/GCLK6
AE21
TCON11/CS5/HCON
AF21
TCON10/CS4/OPT_N
AD20
TCON9/CS3/OPT_P
AE20
TCON16/WPWM
AF20
TCON12/DPM
AF19
TCON1/STV/GSP/VST
AD18
TCON5/TP/SOE
AE18
TCON14/SACN_BLK
AF18
TCON21/CS10/VGH_ODD
AB22
TCON20/CS9/VGH_EVEN
AB23
TCON13/LEDON
AC23
TCON17/CS6/GCLK4
AC22
NC_26
AB16
NC_19
AA14
NC_30
AC15
NC_15
Y16
NC_31
AC16
NC_29
AC14
NC_21
AA16
NC_20
AA15
NC_11
Y10
NC_17
AA11
NC_25
AB15
NC_24
AB14
LGE105D(S7-Tcon Divx_ Non_RM)
IC101-*4
S7T_DIVX & MS10
NC_43
AE1
NC_73
AF16
NC_59
AF1
NC_45
AE3
NC_40
AD14
NC_29
AD3
NC_72
AF15
NC_60
AF2
NC_57
AE15
NC_28
AD2
NC_42
AD16
NC_41
AD15
NC_58
AE16
NC_61
AF3
NC_71
AF14
NC_27
AD1
NC_39
AD13
NC_56
AE14
NC_55
AE13
NC_46
AE4
NC_31
AD5
NC_62
AF4
NC_30
AD4
NC_44
AE2
NC_66
AF8
NC_35
AD9
NC_51
AE9
NC_67
AF9
NC_53
AE11
NC_64
AF6
NC_48
AE6
NC_69
AF11
NC_32
AD6
NC_38
AD12
NC_47
AE5
NC_70
AF12
NC_63
AF5
NC_54
AE12
NC_52
AE10
NC_65
AF7
NC_37
AD11
NC_33
AD7
NC_36
AD10
NC_49
AE7
NC_68
AF10
NC_34
AD8
NC_50
AE8
NC_12
Y11
GND_105
Y19
RLV3P
W26
RLV3N
W25
RLV0P
U26
RLV0N
U25
RLV1P
U24
RLV1N
V26
RLV2P
V25
RLV2N
V24
RLVCKP
W24
RLVCKN
Y26
RLV4P
Y25
RLV4N
Y24
WPWM
AC26
OPTP/FLK2
AC25
RLV5P
AA26
RLV5N
AA25
RLV6P
AA24
RLV6N
AB26
RLV7P
AB25
RLV7N
AB24
OPTN/FLK3
AC24
FLK
AD26
GCLK6
AD25
GCLK5
AD24
LLV3P
AD23
LLV3N
AE23
LLV0P
AE26
LLV0N
AE25
LLV1P
AF26
LLV1N
AF25
LLV2P
AE24
LLV2N
AF24
LLVCKP
AF23
LLVCKN
AD22
LLV4P
AE22
LLV4N
AF22
GOE/GCLK1
AD19
GSC/GCLK3
AE19
LLV5P
AD21
LLV5N
AE21
LLV6P
AF21
LLV6N
AD20
LLV7P
AE20
LLV7N
AF20
GSPR
AF19
GSP/VST
AD18
SOE
AE18
POL
AF18
VDD_ODD
AB22
VDD_EVEN
AB23
GCLK4
AC23
GCLK2
AC22
NC_23
AB16
DPM
AA14
HCON
AC15
NC_15
Y16
NC_26
AC16
LEDON
AC14
NC_20
AA16
NC_19
AA15
NC_11
Y10
NC_17
AA11
SCAN_BLK
AB15
SCAN_BLK1
AB14
LGE101 (S7 NON_TON/DiX/RM)
IC101-*10
S7_NON_DIVX & MS10
NC_48
AE1
NC_78
AF16
NC_64
AF1
NC_50
AE3
NC_45
AD14
NC_34
AD3
NC_77
AF15
NC_65
AF2
NC_62
AE15
NC_33
AD2
NC_47
AD16
NC_46
AD15
NC_63
AE16
NC_66
AF3
NC_76
AF14
NC_32
AD1
NC_44
AD13
NC_61
AE14
NC_60
AE13
NC_51
AE4
NC_36
AD5
NC_67
AF4
NC_35
AD4
NC_49
AE2
NC_71
AF8
NC_40
AD9
NC_56
AE9
NC_72
AF9
NC_58
AE11
NC_69
AF6
NC_53
AE6
NC_74
AF11
NC_37
AD6
NC_43
AD12
NC_52
AE5
NC_75
AF12
NC_68
AF5
NC_59
AE12
NC_57
AE10
NC_70
AF7
NC_42
AD11
NC_38
AD7
NC_41
AD10
NC_54
AE7
NC_73
AF10
NC_39
AD8
NC_55
AE8
NC_12
Y11
GND_105
Y19
LVACLKP/LLV6P/BLUE[3]
W26
LVACLKN/LLV6N/BLUE[2]
W25
LVA0P/LLV3P/BLUE[9]
U26
LVA0N/LLV3N/BLUE[8]
U25
LVA1P/LLV4P/BLUE[7]
U24
LVA1N/LLV4N/BLUE[6]
V26
LVA2P/LLV5P/BLUE[5]
V25
LVA2N/LLV5N/BLUE[4]
V24
LVA3P/LLV7P/BLUE[1]
W24
LVA3N/LLV7N/BLUE[0]
Y26
LVA4P/LLV8P
Y25
LVA4N/LLV8N
Y24
LVBCLKP/LLV0P/GREEN[5]
AC26
LVBCLKN/LLV0N/GREEN[4]
AC25
LVB0P/RLV6P/RED[1]
AA26
LVB0N/RLV6N/RED[0]
AA25
LVB1P/RLV7P/GREEN[9]
AA24
LVB1N/RLV7N/GREEN[8]
AB26
LVB2P/RLV8P/GREEN[7]
AB25
LVB2N/RLV8N/GREEN[6]
AB24
LVB3P/LLV1P/GREEN[3]
AC24
LVB3N/LLV1N/GREEN[2]
AD26
LVB4P/LLV0P/GREEN[1]
AD25
LVB4N/LLV0N/GREEN[0]
AD24
RLV3P/RED[7]
AD23
RLV3N/RED[6]
AE23
RLV0P/LVSYNC
AE26
RLV0N/LHSYNC
AE25
RLV1N/LCK
AF26
RLV2P/RED[9]
AF25
RLV1P/LDE
AE24
RLV2N/RED[8]
AF24
RLV4P/RED[5]
AF23
RLV4N/RED[4]
AD22
RLV5P/RED[3]
AE22
RLV5N/RED[2]
AF22
TCON3/OE/GOE/GCLK2
AD19
TCON15/SCAN_BLK1
AE19
TCON18/CS7/GCLK5
AD21
TCON19/CS8/GCLK6
AE21
TCON11/CS5/HCON
AF21
TCON10/CS4/OPT_N
AD20
TCON9/CS3/OPT_P
AE20
TCON16/WPWM
AF20
TCON12/DPM
AF19
TCON1/STV/GSP/VST
AD18
TCON5/TP/SOE
AE18
TCON14/SACN_BLK
AF18
TCON21/CS10/VGH_ODD
AB22
TCON20/CS9/VGH_EVEN
AB23
TCON13/LEDON
AC23
TCON17/CS6/GCLK4
AC22
NC_26
AB16
NC_19
AA14
NC_30
AC15
NC_15
Y16
NC_31
AC16
NC_29
AC14
NC_21
AA16
NC_20
AA15
NC_11
Y10
NC_17
AA11
NC_25
AB15
NC_24
AB14
LGE105 (S7-Tcon Non_Divx/RM)
IC101-*6
S7T_NON_DIVX & MS10
NC_43
AE1
NC_73
AF16
NC_59
AF1
NC_45
AE3
NC_40
AD14
NC_29
AD3
NC_72
AF15
NC_60
AF2
NC_57
AE15
NC_28
AD2
NC_42
AD16
NC_41
AD15
NC_58
AE16
NC_61
AF3
NC_71
AF14
NC_27
AD1
NC_39
AD13
NC_56
AE14
NC_55
AE13
NC_46
AE4
NC_31
AD5
NC_62
AF4
NC_30
AD4
NC_44
AE2
NC_66
AF8
NC_35
AD9
NC_51
AE9
NC_67
AF9
NC_53
AE11
NC_64
AF6
NC_48
AE6
NC_69
AF11
NC_32
AD6
NC_38
AD12
NC_47
AE5
NC_70
AF12
NC_63
AF5
NC_54
AE12
NC_52
AE10
NC_65
AF7
NC_37
AD11
NC_33
AD7
NC_36
AD10
NC_49
AE7
NC_68
AF10
NC_34
AD8
NC_50
AE8
NC_12
Y11
GND_105
Y19
RLV3P
W26
RLV3N
W25
RLV0P
U26
RLV0N
U25
RLV1P
U24
RLV1N
V26
RLV2P
V25
RLV2N
V24
RLVCKP
W24
RLVCKN
Y26
RLV4P
Y25
RLV4N
Y24
WPWM
AC26
OPTP/FLK2
AC25
RLV5P
AA26
RLV5N
AA25
RLV6P
AA24
RLV6N
AB26
RLV7P
AB25
RLV7N
AB24
OPTN/FLK3
AC24
FLK
AD26
GCLK6
AD25
GCLK5
AD24
LLV3P
AD23
LLV3N
AE23
LLV0P
AE26
LLV0N
AE25
LLV1P
AF26
LLV1N
AF25
LLV2P
AE24
LLV2N
AF24
LLVCKP
AF23
LLVCKN
AD22
LLV4P
AE22
LLV4N
AF22
GOE/GCLK1
AD19
GSC/GCLK3
AE19
LLV5P
AD21
LLV5N
AE21
LLV6P
AF21
LLV6N
AD20
LLV7P
AE20
LLV7N
AF20
GSPR
AF19
GSP/VST
AD18
SOE
AE18
POL
AF18
VDD_ODD
AB22
VDD_EVEN
AB23
GCLK4
AC23
GCLK2
AC22
NC_23
AB16
DPM
AA14
HCON
AC15
NC_15
Y16
NC_26
AC16
LEDON
AC14
NC_20
AA16
NC_19
AA15
NC_11
Y10
NC_17
AA11
SCAN_BLK
AB15
SCAN_BLK1
AB14
LGE107 (S7M Non Divx/RM)
IC101-*2
S7M_NON_DIVX & MS10
FRC_DDR3_A0/DDR2_NC
AE1
FRC_DDR3_A1/DDR2_A6
AF16
FRC_DDR3_A2/DDR2_A7
AF1
FRC_DDR3_A3/DDR2_A1
AE3
FRC_DDR3_A4/DDR2_CASZ
AD14
FRC_DDR3_A5/DDR2_A10
AD3
FRC_DDR3_A6/DDR2_A0
AF15
FRC_DDR3_A7/DDR2_A5
AF2
FRC_DDR3_A8/DDR2_A2
AE15
FRC_DDR3_A9/DDR2_A9
AD2
FRC_DDR3_A10/DDR2_A11
AD16
FRC_DDR3_A11/DDR2_A4
AD15
FRC_DDR3_A12/DDR2_A8
AE16
FRC_DDR3_BA0/DDR2_BA2
AF3
FRC_DDR3_BA1/DDR2_ODT
AF14
FRC_DDR3_BA2/DDR2_A12
AD1
FRC_DDR3_MCLK/DDR2_MCLK
AD13
FRC_DDR3_CKE/DDR2_RASZ
AE14
FRC_DDR3_MCLKZ/DDR2_MCLKZ
AE13
FRC_DDR3_ODT/DDR2_BA1
AE4
FRC_DDR3_RASZ/DDR2_WEZ
AD5
FRC_DDR3_CASZ/DDR2_CKE
AF4
FRC_DDR3_WEZ/DDR2_BA0
AD4
FRC_DDR3_RESETB/DDR2_A3
AE2
FRC_DDR3_DQSL/DDR2_DQS0
AF8
FRC_DDR3_DQSLB/DDR2_DQSB0
AD9
FRC_DDR3_DQSU/DDR2_DQS1
AE9
FRC_DDR3_DQSUB/DDR2_DQSB1
AF9
FRC_DDR3_DML/DDR2_DQ7
AE11
FRC_DDR3_DMU/DDR2_DQ11
AF6
FRC_DDR3_DQL0/DDR2_DQ6
AE6
FRC_DDR3_DQL1/DDR2_DQ0
AF11
FRC_DDR3_DQL2/DDR2_DQ1
AD6
FRC_DDR3_DQL3/DDR2_DQ2
AD12
FRC_DDR3_DQL4/DDR2_DQ4
AE5
FRC_DDR3_DQL5/DDR2_NC
AF12
FRC_DDR3_DQL6/DDR2_DQ3
AF5
FRC_DDR3_DQL7/DDR2_DQ5
AE12
FRC_DDR3_DQU0/DDR2_DQ8
AE10
FRC_DDR3_DQU1/DDR2_DQ14
AF7
FRC_DDR3_DQU2/DDR2_DQ13
AD11
FRC_DDR3_DQU3/DDR2_DQ12
AD7
FRC_DDR3_DQU4/DDR2_DQ15
AD10
FRC_DDR3_DQU5/DDR2_DQ9
AE7
FRC_DDR3_DQU6/DDR2_DQ10
AF10
FRC_DDR3_DQU7/DDR2_DQM1
AD8
FRC_DDR3_NC/DDR2_DQM0
AE8
FRC_REXT
Y11
FRC_TESTPIN
Y19
ACKP/RLV3P/RED[3]
W26
ACKM/RLV3N/RED[2]
W25
A0P/RLV0P/RED[9]
U26
A0M/RLV0N/RED[8]
U25
A1P/RLV1P/RED[7]
U24
A1M/RLV1N/RED[6]
V26
A2P/RLV2P/RED[5]
V25
A2M/RLV2N/RED[4]
V24
A3P/RLV4P/RED[1]
W24
A3M/RLV4N/RED[0]
Y26
A4P/RLV5P/GREEN[9]
Y25
A4M/RLV5N/GREEN[8]
Y24
BCKP/TCON13/GREEN[1]
AC26
BCKM/TCON12/GREEN[0]
AC25
B0P/RLV6P/GREEN[7]
AA26
B0M/RLV6N/GREEN[6]
AA25
B1P/RLV7P/GREEN[5]
AA24
B1M/RLV7N/GREEN[4]
AB26
B2P/RLV8P/GREEN[3]
AB25
B2M/RLV8N/GREEN[2]
AB24
B3P/TCON11/BLUE[9]
AC24
B3M/TCON10/BLUE[8]
AD26
B4P/TCON9/BLUE[7]
AD25
B4M/TCON8/BLUE[6]
AD24
CCKP/LLV3P
AD23
CCKM/LLV3N
AE23
C0P/LLV0P/BLUE[5]
AE26
C0M/LLV0N/BLUE[4]
AE25
C1P/LLV1P/BLUE[3]
AF26
C1M/LLV1N/BLUE[2]
AF25
C2P/LLV2P/BLUE[1]
AE24
C2M/LLV2N/BLUE[0]
AF24
C3P/LLV4P
AF23
C3M/LLV4N
AD22
C4P/LLV5P
AE22
C4M/LLV5N
AF22
DCKP/TCON5
AD19
DCKM/TCON4
AE19
D0P/LLV6P
AD21
D0M/LLV6N
AE21
D1P/LLV7P
AF21
D1M/LLV7N
AD20
D2P/LLV8P
AE20
D2M/LLV8N
AF20
D3P/TCON3
AF19
D3M/TCON2
AD18
D4P/TCON1
AE18
D4M/TCON0
AF18
GPIO0/TCON15/HSYNC/VDD_ODD
AB22
GPIO1/TCON14/VSYNC/VDD_EVEN
AB23
GPIO2/TCON7/LDE/GCLK4
AC23
GPIO3/TCON6/LCK/GCLK2
AC22
FRC_GPIO0/UART_RX
AB16
FRC_GPIO1
AA14
FRC_GPIO3
AC15
FRC_GPIO8
Y16
FRC_GPIO9/UART_TX
AC16
FRC_GPIO10
AC14
FRC_I2CM_DA
AA16
FRC_I2CM_CK
AA15
FRC_I2CS_DA
Y10
FRC_I2CS_CK
AA11
FRC_PWM0
AB15
FRC_PWM1
AB14
LGE107DB-LF-1 (S7M Divx_Non RM/MS10)
IC101-*1
S7M_DIVX & DD
FRC_DDR3_A0/DDR2_NC
AE1
FRC_DDR3_A1/DDR2_A6
AF16
FRC_DDR3_A2/DDR2_A7
AF1
FRC_DDR3_A3/DDR2_A1
AE3
FRC_DDR3_A4/DDR2_CASZ
AD14
FRC_DDR3_A5/DDR2_A10
AD3
FRC_DDR3_A6/DDR2_A0
AF15
FRC_DDR3_A7/DDR2_A5
AF2
FRC_DDR3_A8/DDR2_A2
AE15
FRC_DDR3_A9/DDR2_A9
AD2
FRC_DDR3_A10/DDR2_A11
AD16
FRC_DDR3_A11/DDR2_A4
AD15
FRC_DDR3_A12/DDR2_A8
AE16
FRC_DDR3_BA0/DDR2_BA2
AF3
FRC_DDR3_BA1/DDR2_ODT
AF14
FRC_DDR3_BA2/DDR2_A12
AD1
FRC_DDR3_MCLK/DDR2_MCLK
AD13
FRC_DDR3_CKE/DDR2_RASZ
AE14
FRC_DDR3_MCLKZ/DDR2_MCLKZ
AE13
FRC_DDR3_ODT/DDR2_BA1
AE4
FRC_DDR3_RASZ/DDR2_WEZ
AD5
FRC_DDR3_CASZ/DDR2_CKE
AF4
FRC_DDR3_WEZ/DDR2_BA0
AD4
FRC_DDR3_RESETB/DDR2_A3
AE2
FRC_DDR3_DQSL/DDR2_DQS0
AF8
FRC_DDR3_DQSLB/DDR2_DQSB0
AD9
FRC_DDR3_DQSU/DDR2_DQS1
AE9
FRC_DDR3_DQSUB/DDR2_DQSB1
AF9
FRC_DDR3_DML/DDR2_DQ7
AE11
FRC_DDR3_DMU/DDR2_DQ11
AF6
FRC_DDR3_DQL0/DDR2_DQ6
AE6
FRC_DDR3_DQL1/DDR2_DQ0
AF11
FRC_DDR3_DQL2/DDR2_DQ1
AD6
FRC_DDR3_DQL3/DDR2_DQ2
AD12
FRC_DDR3_DQL4/DDR2_DQ4
AE5
FRC_DDR3_DQL5/DDR2_NC
AF12
FRC_DDR3_DQL6/DDR2_DQ3
AF5
FRC_DDR3_DQL7/DDR2_DQ5
AE12
FRC_DDR3_DQU0/DDR2_DQ8
AE10
FRC_DDR3_DQU1/DDR2_DQ14
AF7
FRC_DDR3_DQU2/DDR2_DQ13
AD11
FRC_DDR3_DQU3/DDR2_DQ12
AD7
FRC_DDR3_DQU4/DDR2_DQ15
AD10
FRC_DDR3_DQU5/DDR2_DQ9
AE7
FRC_DDR3_DQU6/DDR2_DQ10
AF10
FRC_DDR3_DQU7/DDR2_DQM1
AD8
FRC_DDR3_NC/DDR2_DQM0
AE8
FRC_REXT
Y11
FRC_TESTPIN
Y19
ACKP/RLV3P/RED[3]
W26
ACKM/RLV3N/RED[2]
W25
A0P/RLV0P/RED[9]
U26
A0M/RLV0N/RED[8]
U25
A1P/RLV1P/RED[7]
U24
A1M/RLV1N/RED[6]
V26
A2P/RLV2P/RED[5]
V25
A2M/RLV2N/RED[4]
V24
A3P/RLV4P/RED[1]
W24
A3M/RLV4N/RED[0]
Y26
A4P/RLV5P/GREEN[9]
Y25
A4M/RLV5N/GREEN[8]
Y24
BCKP/TCON13/GREEN[1]
AC26
BCKM/TCON12/GREEN[0]
AC25
B0P/RLV6P/GREEN[7]
AA26
B0M/RLV6N/GREEN[6]
AA25
B1P/RLV7P/GREEN[5]
AA24
B1M/RLV7N/GREEN[4]
AB26
B2P/RLV8P/GREEN[3]
AB25
B2M/RLV8N/GREEN[2]
AB24
B3P/TCON11/BLUE[9]
AC24
B3M/TCON10/BLUE[8]
AD26
B4P/TCON9/BLUE[7]
AD25
B4M/TCON8/BLUE[6]
AD24
CCKP/LLV3P
AD23
CCKM/LLV3N
AE23
C0P/LLV0P/BLUE[5]
AE26
C0M/LLV0N/BLUE[4]
AE25
C1P/LLV1P/BLUE[3]
AF26
C1M/LLV1N/BLUE[2]
AF25
C2P/LLV2P/BLUE[1]
AE24
C2M/LLV2N/BLUE[0]
AF24
C3P/LLV4P
AF23
C3M/LLV4N
AD22
C4P/LLV5P
AE22
C4M/LLV5N
AF22
DCKP/TCON5
AD19
DCKM/TCON4
AE19
D0P/LLV6P
AD21
D0M/LLV6N
AE21
D1P/LLV7P
AF21
D1M/LLV7N
AD20
D2P/LLV8P
AE20
D2M/LLV8N
AF20
D3P/TCON3
AF19
D3M/TCON2
AD18
D4P/TCON1
AE18
D4M/TCON0
AF18
GPIO0/TCON15/HSYNC/VDD_ODD
AB22
GPIO1/TCON14/VSYNC/VDD_EVEN
AB23
GPIO2/TCON7/LDE/GCLK4
AC23
GPIO3/TCON6/LCK/GCLK2
AC22
FRC_GPIO0/UART_RX
AB16
FRC_GPIO1
AA14
FRC_GPIO3
AC15
FRC_GPIO8
Y16
FRC_GPIO9/UART_TX
AC16
FRC_GPIO10
AC14
FRC_I2CM_DA
AA16
FRC_I2CM_CK
AA15
FRC_I2CS_DA
Y10
FRC_I2CS_CK
AA11
FRC_PWM0
AB15
FRC_PWM1
AB14
LGE107B-LF-1 (S7M Non Divx/RM/MS10)
IC101-*3
S7M_NON_DIVX & DD
FRC_DDR3_A0/DDR2_NC
AE1
FRC_DDR3_A1/DDR2_A6
AF16
FRC_DDR3_A2/DDR2_A7
AF1
FRC_DDR3_A3/DDR2_A1
AE3
FRC_DDR3_A4/DDR2_CASZ
AD14
FRC_DDR3_A5/DDR2_A10
AD3
FRC_DDR3_A6/DDR2_A0
AF15
FRC_DDR3_A7/DDR2_A5
AF2
FRC_DDR3_A8/DDR2_A2
AE15
FRC_DDR3_A9/DDR2_A9
AD2
FRC_DDR3_A10/DDR2_A11
AD16
FRC_DDR3_A11/DDR2_A4
AD15
FRC_DDR3_A12/DDR2_A8
AE16
FRC_DDR3_BA0/DDR2_BA2
AF3
FRC_DDR3_BA1/DDR2_ODT
AF14
FRC_DDR3_BA2/DDR2_A12
AD1
FRC_DDR3_MCLK/DDR2_MCLK
AD13
FRC_DDR3_CKE/DDR2_RASZ
AE14
FRC_DDR3_MCLKZ/DDR2_MCLKZ
AE13
FRC_DDR3_ODT/DDR2_BA1
AE4
FRC_DDR3_RASZ/DDR2_WEZ
AD5
FRC_DDR3_CASZ/DDR2_CKE
AF4
FRC_DDR3_WEZ/DDR2_BA0
AD4
FRC_DDR3_RESETB/DDR2_A3
AE2
FRC_DDR3_DQSL/DDR2_DQS0
AF8
FRC_DDR3_DQSLB/DDR2_DQSB0
AD9
FRC_DDR3_DQSU/DDR2_DQS1
AE9
FRC_DDR3_DQSUB/DDR2_DQSB1
AF9
FRC_DDR3_DML/DDR2_DQ7
AE11
FRC_DDR3_DMU/DDR2_DQ11
AF6
FRC_DDR3_DQL0/DDR2_DQ6
AE6
FRC_DDR3_DQL1/DDR2_DQ0
AF11
FRC_DDR3_DQL2/DDR2_DQ1
AD6
FRC_DDR3_DQL3/DDR2_DQ2
AD12
FRC_DDR3_DQL4/DDR2_DQ4
AE5
FRC_DDR3_DQL5/DDR2_NC
AF12
FRC_DDR3_DQL6/DDR2_DQ3
AF5
FRC_DDR3_DQL7/DDR2_DQ5
AE12
FRC_DDR3_DQU0/DDR2_DQ8
AE10
FRC_DDR3_DQU1/DDR2_DQ14
AF7
FRC_DDR3_DQU2/DDR2_DQ13
AD11
FRC_DDR3_DQU3/DDR2_DQ12
AD7
FRC_DDR3_DQU4/DDR2_DQ15
AD10
FRC_DDR3_DQU5/DDR2_DQ9
AE7
FRC_DDR3_DQU6/DDR2_DQ10
AF10
FRC_DDR3_DQU7/DDR2_DQM1
AD8
FRC_DDR3_NC/DDR2_DQM0
AE8
FRC_REXT
Y11
FRC_TESTPIN
Y19
ACKP/RLV3P/RED[3]
W26
ACKM/RLV3N/RED[2]
W25
A0P/RLV0P/RED[9]
U26
A0M/RLV0N/RED[8]
U25
A1P/RLV1P/RED[7]
U24
A1M/RLV1N/RED[6]
V26
A2P/RLV2P/RED[5]
V25
A2M/RLV2N/RED[4]
V24
A3P/RLV4P/RED[1]
W24
A3M/RLV4N/RED[0]
Y26
A4P/RLV5P/GREEN[9]
Y25
A4M/RLV5N/GREEN[8]
Y24
BCKP/TCON13/GREEN[1]
AC26
BCKM/TCON12/GREEN[0]
AC25
B0P/RLV6P/GREEN[7]
AA26
B0M/RLV6N/GREEN[6]
AA25
B1P/RLV7P/GREEN[5]
AA24
B1M/RLV7N/GREEN[4]
AB26
B2P/RLV8P/GREEN[3]
AB25
B2M/RLV8N/GREEN[2]
AB24
B3P/TCON11/BLUE[9]
AC24
B3M/TCON10/BLUE[8]
AD26
B4P/TCON9/BLUE[7]
AD25
B4M/TCON8/BLUE[6]
AD24
CCKP/LLV3P
AD23
CCKM/LLV3N
AE23
C0P/LLV0P/BLUE[5]
AE26
C0M/LLV0N/BLUE[4]
AE25
C1P/LLV1P/BLUE[3]
AF26
C1M/LLV1N/BLUE[2]
AF25
C2P/LLV2P/BLUE[1]
AE24
C2M/LLV2N/BLUE[0]
AF24
C3P/LLV4P
AF23
C3M/LLV4N
AD22
C4P/LLV5P
AE22
C4M/LLV5N
AF22
DCKP/TCON5
AD19
DCKM/TCON4
AE19
D0P/LLV6P
AD21
D0M/LLV6N
AE21
D1P/LLV7P
AF21
D1M/LLV7N
AD20
D2P/LLV8P
AE20
D2M/LLV8N
AF20
D3P/TCON3
AF19
D3M/TCON2
AD18
D4P/TCON1
AE18
D4M/TCON0
AF18
GPIO0/TCON15/HSYNC/VDD_ODD
AB22
GPIO1/TCON14/VSYNC/VDD_EVEN
AB23
GPIO2/TCON7/LDE/GCLK4
AC23
GPIO3/TCON6/LCK/GCLK2
AC22
FRC_GPIO0/UART_RX
AB16
FRC_GPIO1
AA14
FRC_GPIO3
AC15
FRC_GPIO8
Y16
FRC_GPIO9/UART_TX
AC16
FRC_GPIO10
AC14
FRC_I2CM_DA
AA16
FRC_I2CM_CK
AA15
FRC_I2CS_DA
Y10
FRC_I2CS_CK
AA11
FRC_PWM0
AB15
FRC_PWM1
AB14
LGE105DB-LF-1 (S7-Tcon Divx_ Non_RM/MS10)
IC101-*5
S7T_DIVX & DD
NC_43
AE1
NC_73
AF16
NC_59
AF1
NC_45
AE3
NC_40
AD14
NC_29
AD3
NC_72
AF15
NC_60
AF2
NC_57
AE15
NC_28
AD2
NC_42
AD16
NC_41
AD15
NC_58
AE16
NC_61
AF3
NC_71
AF14
NC_27
AD1
NC_39
AD13
NC_56
AE14
NC_55
AE13
NC_46
AE4
NC_31
AD5
NC_62
AF4
NC_30
AD4
NC_44
AE2
NC_66
AF8
NC_35
AD9
NC_51
AE9
NC_67
AF9
NC_53
AE11
NC_64
AF6
NC_48
AE6
NC_69
AF11
NC_32
AD6
NC_38
AD12
NC_47
AE5
NC_70
AF12
NC_63
AF5
NC_54
AE12
NC_52
AE10
NC_65
AF7
NC_37
AD11
NC_33
AD7
NC_36
AD10
NC_49
AE7
NC_68
AF10
NC_34
AD8
NC_50
AE8
NC_12
Y11
GND_105
Y19
RLV3P
W26
RLV3N
W25
RLV0P
U26
RLV0N
U25
RLV1P
U24
RLV1N
V26
RLV2P
V25
RLV2N
V24
RLVCKP
W24
RLVCKN
Y26
RLV4P
Y25
RLV4N
Y24
WPWM
AC26
OPTP/FLK2
AC25
RLV5P
AA26
RLV5N
AA25
RLV6P
AA24
RLV6N
AB26
RLV7P
AB25
RLV7N
AB24
OPTN/FLK3
AC24
FLK
AD26
GCLK6
AD25
GCLK5
AD24
LLV3P
AD23
LLV3N
AE23
LLV0P
AE26
LLV0N
AE25
LLV1P
AF26
LLV1N
AF25
LLV2P
AE24
LLV2N
AF24
LLVCKP
AF23
LLVCKN
AD22
LLV4P
AE22
LLV4N
AF22
GOE/GCLK1
AD19
GSC/GCLK3
AE19
LLV5P
AD21
LLV5N
AE21
LLV6P
AF21
LLV6N
AD20
LLV7P
AE20
LLV7N
AF20
GSPR
AF19
GSP/VST
AD18
SOE
AE18
POL
AF18
VDD_ODD
AB22
VDD_EVEN
AB23
GCLK4
AC23
GCLK2
AC22
NC_23
AB16
DPM
AA14
HCON
AC15
NC_15
Y16
NC_26
AC16
LEDON
AC14
NC_20
AA16
NC_19
AA15
NC_11
Y10
NC_17
AA11
SCAN_BLK
AB15
SCAN_BLK1
AB14
LGE105B-LF-1 (S7-Tcon Non_Divx/RM/MS10)
IC101-*7
S7T_NON_DIVX & DD
NC_43
AE1
NC_73
AF16
NC_59
AF1
NC_45
AE3
NC_40
AD14
NC_29
AD3
NC_72
AF15
NC_60
AF2
NC_57
AE15
NC_28
AD2
NC_42
AD16
NC_41
AD15
NC_58
AE16
NC_61
AF3
NC_71
AF14
NC_27
AD1
NC_39
AD13
NC_56
AE14
NC_55
AE13
NC_46
AE4
NC_31
AD5
NC_62
AF4
NC_30
AD4
NC_44
AE2
NC_66
AF8
NC_35
AD9
NC_51
AE9
NC_67
AF9
NC_53
AE11
NC_64
AF6
NC_48
AE6
NC_69
AF11
NC_32
AD6
NC_38
AD12
NC_47
AE5
NC_70
AF12
NC_63
AF5
NC_54
AE12
NC_52
AE10
NC_65
AF7
NC_37
AD11
NC_33
AD7
NC_36
AD10
NC_49
AE7
NC_68
AF10
NC_34
AD8
NC_50
AE8
NC_12
Y11
GND_105
Y19
RLV3P
W26
RLV3N
W25
RLV0P
U26
RLV0N
U25
RLV1P
U24
RLV1N
V26
RLV2P
V25
RLV2N
V24
RLVCKP
W24
RLVCKN
Y26
RLV4P
Y25
RLV4N
Y24
WPWM
AC26
OPTP/FLK2
AC25
RLV5P
AA26
RLV5N
AA25
RLV6P
AA24
RLV6N
AB26
RLV7P
AB25
RLV7N
AB24
OPTN/FLK3
AC24
FLK
AD26
GCLK6
AD25
GCLK5
AD24
LLV3P
AD23
LLV3N
AE23
LLV0P
AE26
LLV0N
AE25
LLV1P
AF26
LLV1N
AF25
LLV2P
AE24
LLV2N
AF24
LLVCKP
AF23
LLVCKN
AD22
LLV4P
AE22
LLV4N
AF22
GOE/GCLK1
AD19
GSC/GCLK3
AE19
LLV5P
AD21
LLV5N
AE21
LLV6P
AF21
LLV6N
AD20
LLV7P
AE20
LLV7N
AF20
GSPR
AF19
GSP/VST
AD18
SOE
AE18
POL
AF18
VDD_ODD
AB22
VDD_EVEN
AB23
GCLK4
AC23
GCLK2
AC22
NC_23
AB16
DPM
AA14
HCON
AC15
NC_15
Y16
NC_26
AC16
LEDON
AC14
NC_20
AA16
NC_19
AA15
NC_11
Y10
NC_17
AA11
SCAN_BLK
AB15
SCAN_BLK1
AB14
LGE101DB-LF-1 (S7 Non_Tcon/RM/MS10)
IC101-*9
S7_DIVX & DD
NC_48
AE1
NC_78
AF16
NC_64
AF1
NC_50
AE3
NC_45
AD14
NC_34
AD3
NC_77
AF15
NC_65
AF2
NC_62
AE15
NC_33
AD2
NC_47
AD16
NC_46
AD15
NC_63
AE16
NC_66
AF3
NC_76
AF14
NC_32
AD1
NC_44
AD13
NC_61
AE14
NC_60
AE13
NC_51
AE4
NC_36
AD5
NC_67
AF4
NC_35
AD4
NC_49
AE2
NC_71
AF8
NC_40
AD9
NC_56
AE9
NC_72
AF9
NC_58
AE11
NC_69
AF6
NC_53
AE6
NC_74
AF11
NC_37
AD6
NC_43
AD12
NC_52
AE5
NC_75
AF12
NC_68
AF5
NC_59
AE12
NC_57
AE10
NC_70
AF7
NC_42
AD11
NC_38
AD7
NC_41
AD10
NC_54
AE7
NC_73
AF10
NC_39
AD8
NC_55
AE8
NC_12
Y11
GND_105
Y19
LVACLKP/LLV6P/BLUE[3]
W26
LVACLKN/LLV6N/BLUE[2]
W25
LVA0P/LLV3P/BLUE[9]
U26
LVA0N/LLV3N/BLUE[8]
U25
LVA1P/LLV4P/BLUE[7]
U24
LVA1N/LLV4N/BLUE[6]
V26
LVA2P/LLV5P/BLUE[5]
V25
LVA2N/LLV5N/BLUE[4]
V24
LVA3P/LLV7P/BLUE[1]
W24
LVA3N/LLV7N/BLUE[0]
Y26
LVA4P/LLV8P
Y25
LVA4N/LLV8N
Y24
LVBCLKP/LLV0P/GREEN[5]
AC26
LVBCLKN/LLV0N/GREEN[4]
AC25
LVB0P/RLV6P/RED[1]
AA26
LVB0N/RLV6N/RED[0]
AA25
LVB1P/RLV7P/GREEN[9]
AA24
LVB1N/RLV7N/GREEN[8]
AB26
LVB2P/RLV8P/GREEN[7]
AB25
LVB2N/RLV8N/GREEN[6]
AB24
LVB3P/LLV1P/GREEN[3]
AC24
LVB3N/LLV1N/GREEN[2]
AD26
LVB4P/LLV0P/GREEN[1]
AD25
LVB4N/LLV0N/GREEN[0]
AD24
RLV3P/RED[7]
AD23
RLV3N/RED[6]
AE23
RLV0P/LVSYNC
AE26
RLV0N/LHSYNC
AE25
RLV1N/LCK
AF26
RLV2P/RED[9]
AF25
RLV1P/LDE
AE24
RLV2N/RED[8]
AF24
RLV4P/RED[5]
AF23
RLV4N/RED[4]
AD22
RLV5P/RED[3]
AE22
RLV5N/RED[2]
AF22
TCON3/OE/GOE/GCLK2
AD19
TCON15/SCAN_BLK1
AE19
TCON18/CS7/GCLK5
AD21
TCON19/CS8/GCLK6
AE21
TCON11/CS5/HCON
AF21
TCON10/CS4/OPT_N
AD20
TCON9/CS3/OPT_P
AE20
TCON16/WPWM
AF20
TCON12/DPM
AF19
TCON1/STV/GSP/VST
AD18
TCON5/TP/SOE
AE18
TCON14/SACN_BLK
AF18
TCON21/CS10/VGH_ODD
AB22
TCON20/CS9/VGH_EVEN
AB23
TCON13/LEDON
AC23
TCON17/CS6/GCLK4
AC22
NC_26
AB16
NC_19
AA14
NC_30
AC15
NC_15
Y16
NC_31
AC16
NC_29
AC14
NC_21
AA16
NC_20
AA15
NC_11
Y10
NC_17
AA11
NC_25
AB15
NC_24
AB14
LGE101B-LF-1(S7 Non_Tcon/Divx/RM/MS10)
IC101-*11
S7_NON_DIVX & DD
NC_48
AE1
NC_78
AF16
NC_64
AF1
NC_50
AE3
NC_45
AD14
NC_34
AD3
NC_77
AF15
NC_65
AF2
NC_62
AE15
NC_33
AD2
NC_47
AD16
NC_46
AD15
NC_63
AE16
NC_66
AF3
NC_76
AF14
NC_32
AD1
NC_44
AD13
NC_61
AE14
NC_60
AE13
NC_51
AE4
NC_36
AD5
NC_67
AF4
NC_35
AD4
NC_49
AE2
NC_71
AF8
NC_40
AD9
NC_56
AE9
NC_72
AF9
NC_58
AE11
NC_69
AF6
NC_53
AE6
NC_74
AF11
NC_37
AD6
NC_43
AD12
NC_52
AE5
NC_75
AF12
NC_68
AF5
NC_59
AE12
NC_57
AE10
NC_70
AF7
NC_42
AD11
NC_38
AD7
NC_41
AD10
NC_54
AE7
NC_73
AF10
NC_39
AD8
NC_55
AE8
NC_12
Y11
GND_105
Y19
LVACLKP/LLV6P/BLUE[3]
W26
LVACLKN/LLV6N/BLUE[2]
W25
LVA0P/LLV3P/BLUE[9]
U26
LVA0N/LLV3N/BLUE[8]
U25
LVA1P/LLV4P/BLUE[7]
U24
LVA1N/LLV4N/BLUE[6]
V26
LVA2P/LLV5P/BLUE[5]
V25
LVA2N/LLV5N/BLUE[4]
V24
LVA3P/LLV7P/BLUE[1]
W24
LVA3N/LLV7N/BLUE[0]
Y26
LVA4P/LLV8P
Y25
LVA4N/LLV8N
Y24
LVBCLKP/LLV0P/GREEN[5]
AC26
LVBCLKN/LLV0N/GREEN[4]
AC25
LVB0P/RLV6P/RED[1]
AA26
LVB0N/RLV6N/RED[0]
AA25
LVB1P/RLV7P/GREEN[9]
AA24
LVB1N/RLV7N/GREEN[8]
AB26
LVB2P/RLV8P/GREEN[7]
AB25
LVB2N/RLV8N/GREEN[6]
AB24
LVB3P/LLV1P/GREEN[3]
AC24
LVB3N/LLV1N/GREEN[2]
AD26
LVB4P/LLV0P/GREEN[1]
AD25
LVB4N/LLV0N/GREEN[0]
AD24
RLV3P/RED[7]
AD23
RLV3N/RED[6]
AE23
RLV0P/LVSYNC
AE26
RLV0N/LHSYNC
AE25
RLV1N/LCK
AF26
RLV2P/RED[9]
AF25
RLV1P/LDE
AE24
RLV2N/RED[8]
AF24
RLV4P/RED[5]
AF23
RLV4N/RED[4]
AD22
RLV5P/RED[3]
AE22
RLV5N/RED[2]
AF22
TCON3/OE/GOE/GCLK2
AD19
TCON15/SCAN_BLK1
AE19
TCON18/CS7/GCLK5
AD21
TCON19/CS8/GCLK6
AE21
TCON11/CS5/HCON
AF21
TCON10/CS4/OPT_N
AD20
TCON9/CS3/OPT_P
AE20
TCON16/WPWM
AF20
TCON12/DPM
AF19
TCON1/STV/GSP/VST
AD18
TCON5/TP/SOE
AE18
TCON14/SACN_BLK
AF18
TCON21/CS10/VGH_ODD
AB22
TCON20/CS9/VGH_EVEN
AB23
TCON13/LEDON
AC23
TCON17/CS6/GCLK4
AC22
NC_26
AB16
NC_19
AA14
NC_30
AC15
NC_15
Y16
NC_31
AC16
NC_29
AC14
NC_21
AA16
NC_20
AA15
NC_11
Y10
NC_17
AA11
NC_25
AB15
NC_24
AB14
FLASH/EEPROM/GPIO
GP2_Saturn7M
DIMMING
URSA degug port
for WIRELESS READY
for SERIAL FLASH
/PF_CE0
H : Serial Flash
L : NAND Flash
/PF_CE1
H : 16 bit
L : 8 bit
Boot from SPI flash : 1’b0
Boot from NOR flash : 1’b1
Addr:10101--
I2C
A0’h
(AUD_SCK, AUD_MASTER_CLK, PWM1, PWM0)
EEPROM
for ETHERNET PHY
HDCP EEPROM
NAND FLASH MEMORY
from CI SLOT
TO SCART1
MIPS_no_EJ_NOR8 : 4’h3 (MIPS as host. No EJ PAD. Byte mode NAND flash.)
MIPS_EJ1_NOR8 : 4’h4 (MIPS as host. EJ use PAD1. Byte mode NAND flash.)
MIPS_EJ2_NOR8 : 4’h5 (MIPS as host. EJ use PAD2. Byte mode NAND flash.)
B51_Secure_no scramble : 4’hb (8051 as host. Internal SPI flash secure boot, no scramble)
B51_Sesure_scramble : 4’hc (8051 as host. Internal SPI flash secure boot with scarmble)
for SYSTEM/HDCP
EEPROM&URSA3
Internal demod out
/External demod in
$0.199
Ver. 1.3
1
LD650 Scan
& MS10 :Region that support MS10(ex:DTV Country)
& DD :Region that support only Dolby Digital(ex:AISA Analog/KOREA)
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only

R1001
47K
TP1001
MICOM_DEBUG
P1001
12505WS-12A00
EEPROM for Micom
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
NC_1
NC_2
NC_3
VSS
+3.5V_ST
IC1001
M24C16-WMN6T
MICOM MODEL OPTION
AMP_RESET_N
PANEL_CTL
CEC_ON/OFF
13
1
2
3
4
5
6
7
8
9
10
11
12
+3.5V_ST
R1006 10K
1
2
3
4
8
7
6
5
R1007 100
R1070 100
R1003 0
R1073 10K
WC
+3.5V_ST
R1002 10K
R1072 10K
R1005 10K
VCC
SCL
SDA
R1079 10K
GPIO_LED
NON_GPIO_LED
R1074 10K
R1076 22
R1078 22
R1010 22
R1081 22
R1013 22
TP1002
R1080
22
TP1003
R1008
+3.5V_ST
R1075 10K
TOUCH_KEY
R1011 10K
TACT_KEY
22
PWM_BUZZ/IIC_LED
R1009 10K
R1004 10K
PWM_LED
R1014 4.7K
R1071 10K
B/L_LED
R1012 10K
B/L_LAMP
R1015 4.7K
for Debugger
MICOM_RESET
NEC_ISP_Tx
NEC_ISP_Rx
OCD1A
OCD1B
FLMD0
NEC_ISP_Tx
NEC_ISP_Rx
OCD1A
OCD1B
+3.5V_ST
C1002
0.1uF
MODEL1_OPT_0
MODEL1_OPT_1
MODEL1_OPT_2
MODEL1_OPT_3
NEC_EEPROM_SCL
NEC_EEPROM_SDA
PIN NAME
MODEL_OPT_0
MODEL_OPT_1
MODEL_OPT_2
MODEL_OPT_3
MODEL OPTION
PIN NO.
8
11
30
HIGH
B/L_LED
+3.5V_ST
PWM_BUZZ/IIC_LED
NEC_SCL
OPT NEC_EEPROM_SDA
R1084
10K
LOW
B/L_LAMP
PWM_LED
TOUCH_KEY TACT_KEY
CEC_REMOTE_NEC
POWER_ON/OFF2_1
31 GPIO_LED NON_GPIO_LED
NEC_SDA
NEC_EEPROM_SCL
AMP_MUTE
MODEL1_OPT_0
SOC_RESET
INV_CTL
MODEL1_OPT_1
OCD1B
RF_RESET
MODEL_OPT_0 MODEL_OPT_1 MODEL_OPT_2 MODEL_OPT_3
LOW LOW LOW LOW
HIGH LOW HIGH
LOW
HIGH HIGH HIGH
LOW
HIGH
HIGH
LOW
LOW LOW
LOW
LOW
HIGH
R1020 0
LD350/450/550
R1018 22
R1019 22
R1065 22
R1067 22
R1066 22
R1023 22
R1064 22
R1063 22
R1059 22
R1060 22
19/22/26LE3300(5500)
32/37/42/47/55LE5300(10)
LD420
LE7300
HIGH HIGH TBD
NON_M_REMOTE
M_REMOTE
+3.5V_ST
C1003
0.1uF
P60/SCL0
P61/SDA0
P62/EXSCL0
P63
P33/TI51/TO51/INTP4
P75
P74
P73/KR3
P72/KR2
P71/KR1
P70/KR0
P32/INTP3/OCD1B
1
2
3
4
5
6
7
8
9
10
11
12
48 VDD
47 VSS
46 REGC
13
R1062 22 NON_M_REMOTE
14
IR
IC1002
22
R1036
POWER_ON/OFF2_2
NEC_RXD
WIRELESS_DETECT
R1043 22
UPD78F0513AGA-GAM-AX
15
45 P121/X1/OCD0A
44 P122/X2/EXCLK/OCD0B
43 FLMD0
42 P123/XT1
41 P124/XT2/EXCLKS
16
NEC_MICOM
17
18
19
20
40 RESET
21
37 P120/INTP0/EXLVI
38 P41
39 P40
22
23
P31/INTP2/OCD1A
P30/INTP1
P17/TI50/TO50
P16/TOH1/INTP5
P15/TOH0
P14/RXD6
P13/TXD6
P12/SO10
P11/SL10/RXD0
P10/SCK10/TXD0
AVREF
AVSS
R1061 22 M_REMOTE
RF_ENABLE
OCD1A
OPT
R1086 47K
R1091 10K
GND
POWER_DET
+3.5V_ST
C1006 0.1uF
22
R1069
R1030 10K
LED_B/LG_LOGO
FLMD0
22
R1068
LED_R/BUZZ
C1007 15pF
32.768KHz
R1034
4.7M
CRYSTAL_KDS
NEC_ISP_Rx
NEC_ISP_Tx
C1008 15pF
CRYSTAL_KDS
X1002
R1039 22
R1037 22
MICOM_RESET
X1002-*1
32.768KHz
CRYSTAL_EPSON
R1041 22
NEC_TXD
WIRELESS_PWR_EN
24
R1044 10K
OPT
R1046 47K
R1045 10K
OPT
+3.5V_ST
R1083 10K
OPT
36 P140/PCL/INTP6
35 P00/TI000
34 P01/TI010/TO00
33 P130
32 P20/ANI0
31 ANI1/P21
30 ANI2/P22
29 ANI3/P23
28 ANI4/P24
27 ANI5/P25
26 ANI6/P26
25 ANI7/P27
+3.5V_ST
SW1001
JTP-1127WEM
2 1
C1010
4 3
0.1uF
R1089
20K
+3.5V_ST
C1009 1uF
R1047 20K
1/16W
1%
1/16W
1%
MICOM
R1048 22
R1049 22
OPT
R1050 10K
R1090 22
R1055 22
R1056 22
R1057 22
R1051 22
R1054 22 19-22_LAMP
R1052 10K
B
C
E
Q1001
2SC3052
EDID_WP
RL_ON
OPC_EN
WIRELESS_SW_CTRL
SCART1_MUTE
MODEL1_OPT_3
MODEL1_OPT_2
POWER_ON/OFF1
OLP
SIDE_HP_MUTE
GP2_Saturn7M Ver. 1.4
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
5
KEY2
KEY1

COMMON AREA
New Item Development
EARPHONE BLOCK
HP_LOUT
090:V9
HP_ROUT
090:V8
C1118
10uF
16V
C1119
10uF
16V
PC AUDIO
EXCEPT_CHINA_HOTEL_OPT
JK1102
PEJ027-01
C1115
1000pF
50V
OPT
EXCEPT_CHINA_HOTEL_OPT
C1116
1000pF
50V
OPT
3 E_SPRING
6A T_TERMINAL1
7A B_TERMINAL1
4 R_SPRING
5 T_SPRING
7B B_TERMINAL2
6B T_TERMINAL2
R1125
1K
R1128
1K
Q1101
MMBT3904-(F)
Q1102
MMBT3904-(F)
D1101
AMOTECH
5.6V
OPT
D1102
AMOTECH
5.6V
OPT
C1108
100pF
50V
R1103
470K
R1108
15K
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
C
E
C
E
B
B
B
B
R1107 R1112
C1107 15K 0
100pF R1102
50V 470K
R1110
10K
E
MMBT3904-(F)
Q1104
C
E
MMBT3904-(F)
Q1103
C
R1111
10K
HP_DET
R1113
0
+3.3V_Normal
R1130
10K
R1155
1K
PC_R_IN 090:S13
PC_L_IN 090:S13
GND
L
DETECT
R
JK3301
KJA-PH-0-0177
5
4
3
1
052:I22
052:I22
SPK_R+_HOTEL
SPK_R-_HOTEL
SPDIF_OUT
090:T20
C
Q1105
ISA1530AC1
B
E
R1129
3.3K
+3.5V_ST
OPT
R1152
4.7K
B
Q1106
2SC3052
SPDIF OPTIC JACK
5.15 Mstar Circuit Application
C
E
A
B
GND
IC1104
NL17SZ00DFT2G
1
2
3
OPT
5
4
VCC
Y
SIDE_HP_MUTE
C1117
0.1uF
16V
OPT
R1126
22
+3.3V_Normal
OPT
R1127
0
C1131
0.1uF
16V
GND
VCC
VINPUT
C1121
100pF
50V
1
2
3
4
FIX_POLE
Fiber Optic
JST1223-001
JK1103
RGB PC
DSUB_VSYNC
DSUB_HSYNC
DSUB_B+
DSUB_B-
DSUB_G+
DSUB_G-
DSUB_R+
DSUB_R-
R1133
75
R1134 0
R1135
75
R1136 0
R1137
75
R1138 0
IC1105
AT24C02BN-10SU-1.8
A0
1
A1
2
A2
3
GND
4
C1122
68pF
50V
OPT
R1148
0
OPT
C1123
OPT
OPT
C1124
OPT
OPT
C1125
OPT
VCC
8
WP
7
SCL
6
SDA
5
D1109
30V
D1110
30V
D1111
30V
D1112
30V
C1127
18pF
50V
JK1104
SPG09-DB-010
C1126
68pF
50V
OPT
R1139
4.7K
R1150
0
C1128
18pF
50V
D1113
30V
1
R1142
10K
RED_GND
GND_2
RED
GREEN_GND
DDC_DATA
GREEN
BLUE_GND
H_SYNC
BLUE
NC
V_SYNC
GND_1
SYNC_GND
DDC_CLOCK
DDC_GND
6
D1115
ENKMC2838-T112
A1
C
A2
11
R1140
4.7K
7
12
2
R1141
22
8
D1114
5.6V
OPT
13
3
9
14
4
GP2_Saturn7M
COMMON AREA
10
C1129
0.1uF
16V
15
5
R1143
22
D1116
5.6V
OPT
16 SHILED
+5V_Normal
EDID_WP
RGB_DDC_SCL
RGB_DDC_SDA
+3.3V_Normal
R1146
10K
D1117
5.6V
R1147
1K
DSUB_DET
Ver. 1.0
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
9

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
RS232C
C1101 0.33uF
C1102
0.1uF
C1103
0.1uF
C1104
0.1uF
C1105
0.1uF
C1+
V+
C1-
C2+
C2-
V-
DOUT2
RIN2
1
2
3
4
5
6
7
8
IC1101
MAX3232CDR
EAN41348201
16
15
14
13
12
11
10
9
VCC
GND
DOUT1
RIN1
ROUT1
DIN1
DIN2
ROUT2
+3.5V_ST
C1106
0.1uF
+3.5V_ST
R1109
4.7K
OPT
R1114
4.7K
OPT
D1107
CDS3C30GTH
30V
D1108
CDS3C30GTH
30V
R1157 0
R1156 0
R1154 0
R1153 0
IR_OUT
S7_RXD1
NEC_RXD
S7_TXD1
NEC_TXD
OPT
R1122
0
R1123
100
R1124
100
JP1121
JP1122
9
8
7
6
10
SPG09-DB-009
JK1101
5
4
3
2
1
GP2_Saturn7M
RS232C 9PIN
Ver. 1.0
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
10

(New Item Developmen H:9.2mm)
SIDE_AV
PPJ235-01
JK3302
SIDE_AV_OPT
5A [YL]E-LUG
4A [YL]O-SPRING
3A [YL]CONTACT
4B [WH]O-SPRING
3C [RD]CONTACT
4C [RD]O-SPRING
5C [RD]E-LUG
SIDE_AV_OPT
SIDE_AV_OPT
D3301
30V
R3301
75
SIDE_AV_OPT
D3302
5.6V
SIDE_AV_OPT
D3303
5.6V
SIDE_AV_OPT
D3304
5.6V
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
C3301
100pF
SIDE_AV_OPT
SIDE_AV_OPT
R3303
470K
SIDE_AV_OPT
R3304
470K
SIDE_AV_OPT
L3303
BLM18PG121SN1D
+3.3V_Normal
SIDE_AV_OPT
10K
R3302
SIDE_AV_OPT
L3301
BLM18PG121SN1D
SIDE_AV_OPT
R3305
1K
SIDE_AV_OPT
R3306
SIDE_AV_OPT 10K
C3302
SIDE_AV_OPT 100pF
50V
L3302
SIDE_AV_OPT
BLM18PG121SN1D
R3307
SIDE_AV_OPT 10K
C3303
100pF
50V
C3304
100pF
OPT
SIDE_AV_OPT
R3308
12K
SIDE_AV_OPT
R3309
12K
SIDEAV_CVBS_IN
SIDEAV_DET
SIDEAV_L_IN
SIDEAV_R_IN
GP2_Saturn7M
SIDE AV
Ver. 1.0
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
11

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
KJA-UB-4-0004
JK1450
USB_DIODES
USB DOWN STREAM
5
1
2
3
4
SIGN6409
L1451
MLB-201209-0120P-N2
C1451
22uF
10V
120-ohm
D1451
CDS3C05HDMI1
5.6V
OPT
NC
OUT_2
OUT_1
FLG
D1452
CDS3C05HDMI1
5.6V
OPT
IC1450
AP2191SG-13
8
7
6
5
R1453 0
R1452 0
1
2
3
4
GND
IN_1
IN_2
EN
SIDE_USB_DM
SIDE_USB_DP
TP1451
R1454
10K
C1452
10uF
10V
R1451 47 USB1_OCD
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
$0.077
C1453
0.1uF
+5V_USB
/RST_HUB
+3.3V_Normal
R1455
4.7K
OPT
R1456 0
USB1_CTL

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
B-MA0
A-TMDML
A-TMWEB
B-TMDQU6
A-MDQL2
A-MDQU4
B-TMDQL3
A-MDQSLB
B-TMDQU6
B-TMA7
A-TMCKE
A-TMCKB
B-MDMU
C1236
0.1uF
A-MDQSLB
A-MA10
A-TMA10
B-TMCKB
A-TMA3
B-TMDQSUB
B-TMWEB
B-TMA3
A-TMODT
A-TMDQU0
A-TMDQSU
B-TMDQL6
B-TMCKE
A-TMBA1
B-MODT
B-MDQU2
B-MVREFDQ
B-MDQL0
B-TMA5
B-TMCASB
B-TMBA1
VCC_1.5V_DDR
A-MBA0
A-TMDQU6
A-MDQU2
A-MDQL7
B-MDQSLB
A-MVREFCA
B-MA9
B-MA2
A-MDQL3
A-MODT
B-MDQL4
A-TMDQU0
B-TMA13
A-MCKB
A-TMDQL7
B-TMDQU2
B-MRASB
B-TMDQU4
B-MDQU6
A-TMDQU3
B-MA7
B-MDQU7
B-TMDQL4
A-TMA2
A-MDQL0
B-TMODT
A-MDQSU
L1201
A-MBA1
B-MDQU6
A-TMODT
B-MWEB
B-MDQL6
A-MCKE
A-TMDQL1
A-TMA12
A-MDQL1
C1231
0.1uF
B-MVREFCA
A-TMRASB
B-MDQL1
A-TMDQL7
A-TMDQL6
A-MDQU7
A-MDQU6
C1227
0.1uF
A-MDQL3
B-MCASB
A-MDQU3
B-TMA10
B-TMA11
+1.5V_DDR
A-TMCK
A-MDQL4
B-MA5
B-TMODT
B-TMA12
A-MCK
C1239
0.1uF
A-TMA2
A-MA9
C1221
0.1uF
B-MDQL2
A-TMDQL0
B-TMDQU7
A-MCASB
B-TMDQU3
B-TMA1
A-MDQL6
B-MA8
B-MA3
A-TMCK
B-MDQU1
C1238
0.1uF
C1244
0.1uF
B-MA12
A-TMRASB
A-MA3
A-TMRESETB
B-TMRASB
A-MA5
A-TMDQL4
C1226
0.1uF
16V
A-MVREFDQ
C1202
1000pF
B-MDQL4
C1230
0.1uF
A-MA11
C1235
0.1uF
R1202
1K 1%
A-TMCASB
A-MA2
B-TMA7
R1224
1K 1%
A-MCK
B-MCK
B-MDQU5
A-MDQU5 A-TMDQU2
B-TMCASB
B-TMA4
B-TMDQL0
C1219
0.1uF
B-TMDQL7
C1201
0.1uF
B-TMDQL4
B-TMDQL2
B-MODT
C1206
0.1uF
B-TMCK
B-TMDQU1
B-TMDQL2
C1224
0.1uF
A-MDQU6
R1228
1K 1%
B-TMDQU0
C1232
0.1uF
B-MDQU7
A-MA9
A-TMA0
A-MDQL1
B-TMDQL5
R1203
240
1%
B-TMA6
C1242
0.1uF
B-MA9
B-TMDQL1
A-TMA4
B-TMA12
A-MODT
B-TMDML
B-MDQSUB
B-TMA3
B-MVREFCA
B-MA5
A-MDQSL
A-MA1
B-TMDMU
A-TMDQSL
B-MBA0
C1203
0.1uF
C1237
0.1uF
B-MA12
VCC_1.5V_DDR
A-TMDQL1
A-MA11
B-MCKE
B-MDQSU
B-MDQL7
B-MA4
B-MA4
R1227
1K 1%
A-TMDQSLB
A-MDQU1
B-MDQU5
A-TMCKB
A-TMA6
A-MA6
C1223
0.1uF
VCC_1.5V_DDR
A-TMA8
C1248
0.1uF
B-TMA4
B-MDQL2
A-TMRESETB
C1247
1000pF
B-MDQU2
A-TMDMU
B-TMA9
B-MDQU0
B-TMRESETB
B-TMDQU2
A-TMDMU
B-MA13
C1241
0.1uF
A-MA0
B-TMA8
A-TMDQL5
A-TMDQU6
A-MA4
A-TMDQL3
A-MDML
B-MDQL3
B-MDQU3
B-TMBA0
VCC_1.5V_DDR
R1204
1K 1%
A-MRESETB
A-MWEB
A-TMDQU1
B-MA0
A-TMA13
A-MBA2
A-TMDQSUB
A-TMDQL5
VCC_1.5V_DDR
A-TMBA1
VCC_1.5V_DDR
B-TMDQL6
B-MDQL7
B-TMA10
B-MRESETB
C1214
0.1uF
R1205
1K 1%
A-MA6
B-MA2
B-TMA13
A-TMBA2
C1228
0.1uF
C1208
0.1uF
C1245
0.1uF
A-MRASB
C1210
0.1uF
A-MDQL5
B-MWEB
C1218
0.1uF
A-TMCKE
A-MDQL4
C1229
0.1uF
B-MDQL1
C1233
0.1uF
A-MDQL6
B-TMA11
B-TMDQSU
A-MA3
A-TMDQSL
A-TMDQSLB
R1226
240
1%
A-MA7
B-MA8
A-TMDQL6
A-TMBA0
A-MDQSU
A-MA13
A-MDQSUB
B-MA1
C1250
0.1uF
A-TMA10
B-TMDQU1
B-TMWEB
B-MDQU3
B-TMRESETB
A-MA13
B-TMDML
B-MCKE
B-TMA0
A-MA8
A-MCKB
A-TMDQL3
A-TMA5
A-TMDQU4
A-MA7
B-TMDQSU
A-TMDQSUB
B-MDML
A-MBA2
B-TMDQU4
B-TMA5
A-MDQL2
B-TMDQU0
A-MVREFCA
C1204
1000pF
A-MBA0
C1215
0.1uF
A-MA8
B-MRESETB
B-TMDQSLB
B-TMDQSL
A-MRASB
B-TMA0
B-MBA1
A-TMDQU7
A-MA1
B-MDQU0
A-MDQU0
B-MRASB
B-TMA1
B-TMBA2
A-TMDQL2
A-TMDQU2
A-MRESETB
A-TMDQL2
A-MDQL0
A-TMDML
B-MDQL5
B-TMA8
B-MBA1
A-TMA13
B-MDQSL
B-MDQL3
A-MDQL7
A-TMDQSU
C1212
0.1uF
A-TMA5
A-TMDQU4
B-MDQL0
A-MWEB
B-TMA9
A-TMA0
B-MA10
A-MA12
A-MCKE
B-TMDQSL
A-TMA4
B-TMDQSLB
B-MDQU4
R1225
1K 1%
B-TMDQL1
C1249
1000pF
B-MBA2
B-TMBA1
B-MDQU1
A-MA0
B-MA10
A-MVREFDQ
B-TMDQU7
B-MDQSUB
C1243
0.1uF
A-MDQU2
B-MA13
C1211
0.1uF
A-TMA1
A-MBA1
A-MCASB
B-TMDQL0
B-MDQSL
A-TMA8
B-TMDQL7
A-MDQU3
A-MA5
B-MVREFDQ
B-MA1
B-MDML
B-MDQSU
B-MA6
B-MDMU
B-MCKB
A-MDMU
B-TMDQU5
A-TMDQL0
B-MCK
B-MCASB
A-TMDQU7
A-TMCASB
VCC_1.5V_DDR
A-MA4
VCC_1.5V_DDR
A-MDQU4
B-TMDMU
A-TMA6
A-TMA12
B-TMCK
R1201
1K 1%
B-TMBA2
C1216
0.1uF
C1220
0.1uF
A-MDML
B-TMBA0
VCC_1.5V_DDR
A-MDMU
B-MDQL6
A-MDQU1
B-MBA0
B-TMDQU3
A-TMDQL4
A-MA10
B-TMRASB
B-MCKB
B-MA11
B-MDQU4
A-TMA11
A-TMWEB
A-TMDQU3
B-MA11
B-MBA2
B-TMCKE
B-MDQL5
B-TMDQSUB
A-TMA7
A-TMA9
B-TMA6
B-TMDQL5
B-MA6
A-TMA9
B-MA7
B-MA3
C1222
0.1uF
A-TMA1
A-TMA11
A-MA2
B-TMDQU5
C1217
0.1uF
A-MDQL5
A-TMBA0
C1213
0.1uF
C1207
0.1uF
A-TMDQU1
A-TMDQU5
A-TMDQU5
A-TMBA2
B-TMA2
A-TMA3
C1234
0.1uF
A-MA12
A-MDQU0
B-TMA2
B-MDQSLB
B-TMCKB
A-MDQSUB
A-MDQSL
B-TMDQL3
A-TMA7
A-MDQU7
A-MDQU5
C1205
10uF
C1225
10uF
10V
C1246
10uF
VCC_1.5V_DDR
R1231
10K
VCC_1.5V_DDR
R1232
10K
R1223
10
R1217
10
R1216
10
R1211
10
R1213
10
R1222
10
R1215
10
R1220
10
R1218
10
R1221
10
R1210
10
R1206
10
R1214
10
R1208
10
R1207
10
R1209
10
R1219
10
R1212
10
AR1218
10
AR1215
10
AR1208
10
AR1219
10
AR1216
10
AR1214
10
AR1211
10
AR1220
10
AR1201
10
AR1202
10
AR1217
10
AR1204
10
AR1207
10
AR1210
10
AR1213
10
AR1209
10
AR1203
10
AR1205
10
AR1212
10
AR1206
10
R1234
10K
B-MCKE
A-MCKE
R1233 10K
H5TQ1G63BFR-H9C
IC1202
A0
N3
A1
P7
A2
P3
A3
N2
A4
P8
A5
P2
A6
R8
A7
R2
A8
T8
A9
R3
A10/AP
L7
A11
R7
A12/BC
N7
A13
T3
A15
M7
BA0
M2
BA1
N8
BA2
M3
CK
J7
CK
K7
CKE
K9
CS
L2
ODT
K1
RAS
J3
CAS
K3
WE
L3
RESET
T2
DQSL
F3
DQSL
G3
DQSU
C7
DQSU
B7
DML
E7
DMU
D3
DQL0
E3
DQL1
F7
DQL2
F2
DQL3
F8
DQL4
H3
DQL5
H8
DQL6
G2
DQL7
H7
DQU0
D7
DQU1
C3
DQU2
C8
DQU3
C2
DQU4
A7
DQU5
A2
DQU6
B8
DQU7
A3
VREFCA
M8
VREFDQ
H1
ZQ L8
VDD_1
B2
VDD_2
D9
VDD_3
G7
VDD_4
K2
VDD_5
K8
VDD_6
N1
VDD_7
N9
VDD_8
R1
VDD_9
R9
VDDQ_1
A1
VDDQ_2
A8
VDDQ_3
C1
VDDQ_4
C9
VDDQ_5
D2
VDDQ_6
E9
VDDQ_7
F1
VDDQ_8
H2
VDDQ_9
H9
NC_1
J1
NC_2
J9
NC_3
L1
NC_4
L9
NC_6
T7
VSS_1
A9
VSS_2
B3
VSS_3
E1
VSS_4
G8
VSS_5
J2
VSS_6
J8
VSS_7
M1
VSS_8
M9
VSS_9
P1
VSS_10
P9
VSS_11
T1
VSS_12
T9
VSSQ_1
B1
VSSQ_2
B9
VSSQ_3
D1
VSSQ_4
D8
VSSQ_5
E2
VSSQ_6
E8
VSSQ_7
F9
VSSQ_8
G1
VSSQ_9
G9
H5TQ1G63BFR-H9C
IC1201
A0
N3
A1
P7
A2
P3
A3
N2
A4
P8
A5
P2
A6
R8
A7
R2
A8
T8
A9
R3
A10/AP
L7
A11
R7
A12/BC
N7
A13
T3
A15
M7
BA0
M2
BA1
N8
BA2
M3
CK
J7
CK
K7
CKE
K9
CS
L2
ODT
K1
RAS
J3
CAS
K3
WE
L3
RESET
T2
DQSL
F3
DQSL
G3
DQSU
C7
DQSU
B7
DML
E7
DMU
D3
DQL0
E3
DQL1
F7
DQL2
F2
DQL3
F8
DQL4
H3
DQL5
H8
DQL6
G2
DQL7
H7
DQU0
D7
DQU1
C3
DQU2
C8
DQU3
C2
DQU4
A7
DQU5
A2
DQU6
B8
DQU7
A3
VREFCA
M8
VREFDQ
H1
ZQ
L8
VDD_1
B2
VDD_2
D9
VDD_3
G7
VDD_4
K2
VDD_5
K8
VDD_6
N1
VDD_7
N9
VDD_8
R1
VDD_9
R9
VDDQ_1
A1
VDDQ_2
A8
VDDQ_3
C1
VDDQ_4
C9
VDDQ_5
D2
VDDQ_6
E9
VDDQ_7
F1
VDDQ_8
H2
VDDQ_9
H9
NC_1
J1
NC_2
J9
NC_3
L1
NC_4
L9
NC_6
T7
VSS_1
A9
VSS_2
B3
VSS_3
E1
VSS_4
G8
VSS_5
J2
VSS_6
J8
VSS_7
M1
VSS_8
M9
VSS_9
P1
VSS_10
P9
VSS_11
T1
VSS_12
T9
VSSQ_1
B1
VSSQ_2
B9
VSSQ_3
D1
VSSQ_4
D8
VSSQ_5
E2
VSSQ_6
E8
VSSQ_7
F9
VSSQ_8
G1
VSSQ_9
G9
R1235
56
1%
R1236
56
1%
C1209
0.01uF
25V
R1237
56
1%
R1238
56
1%
C1240
0.01uF
25V
LGE107D (S7M Divx_Non RM)
IC101
S7M_DIVX & MS10
A_DDR3_A0/DDR2_A13
B8
A_DDR3_A1/DDR2_A8
B9
A_DDR3_A2/DDR2_A9
A8
A_DDR3_A3/DDR2_A1
C21
A_DDR3_A4/DDR2_A2
B10
A_DDR3_A5/DDR2_A10
A22
A_DDR3_A6/DDR2_A4
A10
A_DDR3_A7/DDR2_A3
B22
A_DDR3_A8/DDR2_A6
C9
A_DDR3_A9/DDR2_A12
C23
A_DDR3_A10/DDR2_RASZ
B11
A_DDR3_A11/DDR2_A11
A9
A_DDR3_A12/DDR2_A0
C10
A_DDR3_A13/DDR2_A7
B23
A_DDR3_BA0/DDR2_BA2
B21
A_DDR3_BA1/DDR2_CASZ
A11
A_DDR3_BA2/DDR2_A5
A23
A_DDR3_MCLK/DDR2_MCLK
A12
A_DDR3_MCLKZ/DDR2_MCLKZ
C11
A_DDR3_CKE/DDR2_DQ5
B12
A_DDR3_ODT/DDR2_ODT
C20
A_DDR3_RASZ/DDR2_WEZ
A20
A_DDR3_CASZ/DDR2_BA1
B20
A_DDR3_WEZ/DDR2_BA0
A21
A_DDR3_RESETB
C22
A_DDR3_DQSL/DDR2_DQS0
C16
A_DDR3_DQSLB/DDR2_DQSB0
B16
A_DDR3_DQSU/DDR2_DQSB1
A16
A_DDR3_DQSUB/DDR2_DQS1
C15
A_DDR3_DML//DDR2_DQ13
A14
A_DDR3_DMU/DDR2_DQ6
B18
A_DDR3_DQL0/DDR2_DQ3
C18
A_DDR3_DQL1/DDR2_DQ7
B13
A_DDR3_DQL2/DDR2_DQ1
A19
A_DDR3_DQL3/DDR2_DQ10
C13
A_DDR3_DQL4/DDR2_DQ4
C19
A_DDR3_DQL5/DDR2_DQ0
A13
A_DDR3_DQL6/DDR2_CKE
B19
A_DDR3_DQL7/DDR2_DQ2
C12
A_DDR3_DQU0/DDR2_DQ15
A15
A_DDR3_DQU1/DDR2_DQ9
A17
A_DDR3_DQU2/DDR2_DQ8
B14
A_DDR3_DQU3/DDR2_DQ11
C17
A_DDR3_DQU4/DDR2_DQM1
B15
A_DDR3_DQU5/DDR2_DQ12
A18
A_DDR3_DQU6/DDR2_DQM0
C14
A_DDR3_DQU7/DDR2_DQ14
B17
B_DDR3_A0/DDR2_A13
A25
B_DDR3_A1/DDR2_A8
B24
B_DDR3_A2/DDR2_A9
A24
B_DDR3_A3/DDR2_A1
P25
B_DDR3_A4/DDR2_A2
C24
B_DDR3_A5/DDR2_A10
P26
B_DDR3_A6/DDR2_A4
B26
B_DDR3_A7/DDR2_A3
R24
B_DDR3_A8/DDR2_A6
B25
B_DDR3_A9/DDR2_A12
T26
B_DDR3_A10/DDR2_RASZ
D24
B_DDR3_A11/DDR2_A11
A26
B_DDR3_A12/DDR2_A0
C25
B_DDR3_A13/DDR2_A7
T25
B_DDR3_BA0/DDR2_BA2
P24
B_DDR3_BA1/DDR2_CASZ
C26
B_DDR3_BA2/DDR2_A5
R26
B_DDR3_MCLK/DDR2_MCLK
D26
B_DDR3_MCLKZ/DDR2_MCLKZ
D25
B_DDR3_CKE/DDR2_DQ5
E24
B_DDR3_ODT/DDR2_ODT
N25
B_DDR3_RASZ/DDR2_WEZ
M26
B_DDR3_CASZ/DDR2_BA1
N24
B_DDR3_WEZ/DDR2_BA0
N26
B_DDR3_RESETB
R25
B_DDR3_DQSL/DDR2_DQS0
J25
B_DDR3_DQSLB/DDR2_DQSB0
J24
B_DDR3_DQSU/DDR2_DQSB1
H26
B_DDR3_DQSUB/DDR2_DQS1
H25
B_DDR3_DML/DDR2_DQ13
F26
B_DDR3_DMU/DDR2_DQ6
L24
B_DDR3_DQL0/DDR2_DQ3
L25
B_DDR3_DQL1/DDR2_DQ7
F24
B_DDR3_DQL2/DDR2_DQ1
L26
B_DDR3_DQL3/DDR2_DQ10
F25
B_DDR3_DQL4/DDR2_DQ4
M25
B_DDR3_DQL5/DDR2_DQ0
E26
B_DDR3_DQL6/DDR2_CKE
M24
B_DDR3_DQL7/DDR2_DQ2
E25
B_DDR3_DQU0/DDR2_DQ15
G26
B_DDR3_DQU1/DDR2_DQ9
J26
B_DDR3_DQU2/DDR2_DQ8
G24
B_DDR3_DQU3/DDR2_DQ11
K25
B_DDR3_DQU4/DDR2_DQM1
H24
B_DDR3_DQU5/DDR2_DQ12
K26
B_DDR3_DQU6/DDR2_DQM0
G25
B_DDR3_DQU7/DDR2_DQ14
K24
DDR3(256MB)
GP2_Saturn7M
DDR3 1.5V By CAP - Place these Caps near Memory
DDR3 1.5V By CAP - Place these Caps near Memory
CLose to DDR3
CLose to Saturn7M IC CLose to Saturn7M IC
Close to DDR Power Pin
Close to DDR Power Pin
CLose to DDR3
Ver. 1.0
21
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only

FLASH_WP
R1402
0
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
R1401
OPT 0
+3.3V_Normal
B
R1403
10K
C
E
/SPI_CS
SPI_SDO
Q1401
KRC103S
+3.3V_Normal
R1404
4.7K
S_FLASH
IC1401
MX25L8005M2I-15G
CS#
SO
WP#
GND
1
2
3
4
8
7
6
5
VCC
HOLD#
SCLK
SI
+3.3V_Normal
R1405
33
C1401
0.1uF
SPI_SCK
SPI_SDI
GP2_Saturn7M Ver. 1.2
S-Flash(1MB)
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
23

IF_N_EXT
IF_P_EXT
ISDB_DEMOD
C2901 0.1uF
C2902 0.1uF
ISDB_DEMOD
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
PANASONIC (ISDB-T)
MN884433
+1.2V_DE
C2903 0.1uF
ISDB_DEMOD
C2904 0.1uF
ISDB_DEMOD
C2905 0.1uF ISDB_DEMOD
IF_AGC_ISDB
+3.3V_DE
C2906 0.1uF ISDB_DEMOD
ISDB_DEMOD
R2903
10K 1%
C2907 0.1uF ISDB_DEMOD
C2908 0.1uF ISDB_DEMOD
C2909 0.1uF ISDB_DEMOD
ISDB_DEMOD
R2904 2.2K
R2905 2.2K
ISDB_DEMOD
ISDB_DEMOD
R2907 2.2K
ISDB_DEMOD
R2908 2.2K
R2906 10K
ISDB_DEMOD
ISDB_DEMOD
C2910
0.1uF
VSS_1 1
AVDD_S 2
AII_S 3
AIQ_S 4
AVSS_S 5
VRT_S 6
VRB_S 7
TCPO_S 8
VDDL_1 9
MSCL_S 10
MSDA_S 11
VSS_2 12
VSSH 13
PSEL 14
ZSEL 15
VDDL_2 16
ACKI 17
TCPO_T 18
IR_T 19
VRT_T 20
VRB_T 21
AVDD_T 22
AIN_T 23
AIP_T 24
AVSS_T 25
ISDB_DEMOD
C2911
0.1uF
16V
ISDB_DEMOD
C2912
0.1uF
16V
ISDB_DEMOD ISDB_DEMOD
ISDB_DEMOD ISDB_DEMOD ISDB_DEMOD
C2913
0.1uF
16V
C2916 C2917
0.1uF 0.1uF
16V 16V
C2920
0.1uF
16V
C2922
0.1uF
16V
100 AGC_S
99 VDDH_5
98 GPO2
97 DENB
96 PCKB
95 SDOB
94 TEST0
93 SCKB
92 VDDL_7
91 VSS_11
90 HDVDDL1
89 NC_4
88 HDVDDH
87 NC_3
86 RON
85 HDVPP
84 VSS_10
83 VDDH_4
82 DENA
81 PCKA
80 SDOA
79 GPI2
78 SCKA
77 TEST2
76 TEST1
ISDB_DEMOD
C2914
0.1uF
16V
ISDB_DEMOD
C2915
15pF
50V
IC2901
MN884433
ISDB_DEMOD
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VSS_3
MSCL_T
MSDA_T
VDDH_1
GPO1
AGCI_T
AGCR_T
GPO0
VDDL_3
VSS_4
XO
XI
VDDH_2
GPI1
GPI0
TEST4
SHVPP
SHVDDH
NC_1
VSS_5
VDDL_4
TCK
TDI
NRST
TEST3
C2918 C2921 C2923
0.1uF 0.1uF 0.1uF
16V 16V 16V
ISDB_DEMOD ISDB_DEMOD
ISDB_DEMOD
ISDB_OPT
R2909
1M
ISDB_DEMOD
X2901
25MHz
ISDB_DEMOD
C2919
15pF
50V
ISDB_DEMOD
C2924
0.1uF
16V
75 VSS_9
74 INTB
73 INTA
72 SADR
71 VDDH_3
70 SCL
69 SDA
68 VSS_8
67 HDVDDL0
66 SADR_S
65 NC_2
64 SADR_T
63 VDDL_6
62 VSS_7
61 ERRB
60 SYNCB
59 ERRA
58 SYNCA
57 TDO
56 CSEL1
55 CSEL0
54 TMS
53 TRST
52 VDDL_5
51 VSS_6
ISDB_DEMOD
R2910 22
ISDB_DEMOD
R2911 22
ISDB_DEMOD
R2912 22
ISDB_DEMOD
R2913 22
ISDB_DEMOD
C2926 0.1uF
ISDB_DEMOD
C2927 0.1uF
ISDB_DEMOD
C2928 0.1uF
ISDB_DEMOD
C2925 0.1uF
FE_TS_VAL_ERR
FE_TS_SYNC
FE_TS_DATA[0]
(FE_TS_SERIAL)
FE_TS_CLK
OPT
R2914
2.2K
+3.3V_DE
OPT
R2915
2.2K
DEMOD_RESET
DEMOD_SCL
DEMOD_SDA
FE_TS_DATA[0]
(FE_TS_SERIAL)
ISDB_DEMOD TP2901
ISDB_DEMOD TP2902
ISDB_DEMOD TP2903
ISDB_DEMOD TP2904
ISDB_DEMOD TP2905
ISDB_DEMOD TP2906
ISDB_DEMOD TP2907
FE_TS_DATA[0]
FE_TS_DATA[1]
FE_TS_DATA[2]
FE_TS_DATA[3]
FE_TS_DATA[4]
FE_TS_DATA[5]
FE_TS_DATA[6]
FE_TS_DATA[7]
ISDB-T Demodulator
FE_TS_DATA[0-7]
GP2_Saturn7M Ver. 1.0
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
AMP_I2C HAVE PULL-UP
28

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Panasonic Demodulator Power(3.3V,1.2V)
+3.3V_Normal
IF_AGC
ISDB_POWER
C3001
0.1uF
ISDB_POWER
L3001
BLM18PG121SN1D
+3.3V_DE
R3001
0
ISDB_DEMOD
ISDB_POWER
C3002
0.1uF
ISDB_POWER
+3.3V_DE
NC_1
EN
VIN
ISDB_POWER
C3004
10uF NC_2
10V
ISDB_POWER
IC3001
SC4215ISTRT
IF AGC SELECTION
R3002
0
MSTAR DEMOD
IF_AGC_ISDB
IF_AGC_MAIN
C3003
0.1uF
16V
TP3002
1
2
3
4
IF_AGC_SEL
8
7
6
5
GND
ADJ
VO
NC_3
ISDB_POWER
R3003
ISDB_POWER
R3004
5.1K
10K
+1.2V_DE
ISDB_POWER
C3005
0.1uF
16V
ISDB_POWER
C3006
22uF
16V
GP2_Saturn7M Ver. 1.0
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
Demodulator
29

NON CI Region
/PCM_CD
PCM_5V_CTL
/PCM_CE
/PCM_IRQA
FE_TS_SYNC
FE_TS_VAL_ERR
FE_TS_CLK
CI_TS_DATA[0]
CI_TS_DATA[1]
CI_TS_DATA[2]
CI_TS_DATA[3]
CI_TS_DATA[4]
CI_TS_DATA[5]
CI_TS_DATA[6]
CI_TS_DATA[7]
/PCM_REG
/PCM_OE
/PCM_WE
/PCM_IORD
/PCM_IOWR
PCM_RST
/PCM_WAIT
CI_TS_CLK
CI_TS_VAL
CI_TS_SYNC
PCM_A[0]
PCM_A[1]
PCM_A[2]
PCM_A[3]
PCM_A[4]
PCM_A[5]
PCM_A[6]
PCM_A[7]
PCM_A[8]
PCM_A[9]
PCM_A[10]
PCM_A[11]
PCM_A[12]
PCM_A[13]
PCM_A[14]
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
FE_TS_DATA[0-7]
PCM_D[0-7]
FE_TS_DATA[0]
FE_TS_DATA[1]
FE_TS_DATA[2]
FE_TS_DATA[3]
FE_TS_DATA[4]
FE_TS_DATA[5]
FE_TS_DATA[6]
FE_TS_DATA[7]
PCM_D[0]
PCM_D[1]
PCM_D[2]
PCM_D[3]
PCM_D[4]
PCM_D[5]
PCM_D[6]
PCM_D[7]
GP2_Saturn7M Ver. 1.0
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
PCMCI
46

NON Motion Remocon Region
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
TP2501
TP2502
TP2503
TP2504
M_REMOTE_RX
M_REMOTE_TX
RF_RESET
RF_ENABLE
GP2_Saturn7M
NON M REMOCON
Ver. 1.0
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
50

NON CHINA HOTEL
AMP_MUTE_HOTEL
SPK_R+_HOTEL
SPK_R-_HOTEL
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
GP2_Saturn7M Ver. 1.0
NON CHINA HOTEL
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
52

NON-WIRELESS MODEL
S7_RXD
S7_TXD
WIRELESS_SW_CTRL
WIRELESS_PWR_EN
WIRELESS_DETECT
WIRELESS_DL_RX
WIRELESS_DL_TX
R2627 0
R2626 0
S7_RXD1
S7_TXD1
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
GP2_Saturn7M
NON WIRELESS READY
Ver. 1.0
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
54

IF_AGC_SEL
LNA2_CTL
RF_SWITCH_CTL
R7300 100
R7301 100
R7302 100
R7303 100
HDMI
DSUB
R7834 1K
OPT
CK+_HDMI1
CK-_HDMI1
D0+_HDMI1
D0-_HDMI1
D1+_HDMI1
D1-_HDMI1
D2+_HDMI1
D2-_HDMI1
DDC_SDA_1
DDC_SCL_1
HPD1
CK+_HDMI2
CK-_HDMI2
D0+_HDMI2
D0-_HDMI2
D1+_HDMI2
D1-_HDMI2
D2+_HDMI2
D2-_HDMI2
DDC_SDA_2
DDC_SCL_2
HPD2
CK+_HDMI4
CK-_HDMI4
D0+_HDMI4
D0-_HDMI4
D1+_HDMI4
D1-_HDMI4
D2+_HDMI4
D2-_HDMI4
DDC_SDA_4
DDC_SCL_4
HPD4
CEC_REMOTE_S7
DSUB_HSYNC
DSUB_VSYNC
DSUB_R+
DSUB_R-
DSUB_G+
DSUB_G-
DSUB_B+
DSUB_B-
SC1_ID
SC1_FB
SC1_R+/COMP1_Pr+
SC1_R-/COMP1_Pr-
SC1_G+/COMP1_Y+
SC1_G-/COMP1_Y-
SC1_B+/COMP1_Pb+
SC1_B-/COMP1_Pb-
SC1_SOG_IN
COMP2_Pr+
COMP2_Pr-
COMP2_Y+
COMP2_Y-
COMP2_Pb+
COMP2_Pb-
TU_CVBS
SC1_CVBS_IN
AV_CVBS_IN
SIDEAV_CVBS_IN
AV_CVBS_IN2
DTV/MNT_VOUT
AV_CVBS_IN2
R7833 1K
R7379 1K
OPT
R7380 1K
OPT
SCART1_RGB/COMP1
COMP2
CVBS In/OUT
R7377 1K
OPT
R7378 1K
R7306 1K
FHD
R7307 1K
HD
R7304
10K
+3.3V_Normal
R7314 22
R7315 22
MODEL_OPT_0
MODEL_OPT_1
MODEL_OPT_2
MODEL_OPT_3
MODEL_OPT_4
MODEL_OPT_5
R7316 33 C7301 0.047uF
R7317 68 C7302 0.047uF
R7318 33 C7303 0.047uF
R7319 68 C7304 0.047uF
R7320 33 C7305 0.047uF
R7321 68 C7306 0.047uF
R7322 0 C7307 1000pF
R7340 33 C7308 0.047uF
R7341 68 C7309 0.047uF
R7342 33 C7310 0.047uF
R7343 68 C7311 0.047uF
R7344 33 C7312 0.047uF
R7345 68 C7313 0.047uF
R7324 33 C7315 0.047uF
R7325 68 C7316 0.047uF
R7326 33 C7317 0.047uF
R7327 68 C7318 0.047uF
R7328 33 C7319 0.047uF
R7329 68 C7320 0.047uF
R7330 0 C7321 1000pF
R7331 33 C7322 0.047uF
R7332 33 C7323 0.047uF
R7333 33 C7324 0.047uF
R7334 33 C7325 0.047uF
R7335 33 C7326 0.047uF
R7336 33 C7327 0.047uF
R7337 33 C7328 0.047uF
R7338 33 C7329 0.047uF
R7339 68 C7330 0.047uF
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
R7305
R7308 1K
OPT
10K
C7300
1000pF
OPT
TP211
R7309 1K
R7310 1K
OPT
R7311 1K
R7312 1K
OPT
R7313 1K
R7323 0
MODEL OPTION
NON_EU
Close to MSTAR
MODEL_OPT_6
C7314 1000pF
TP7300
IC101
LGE107D (S7M Divx_Non RM)
F1
W2
A_RXCP S7M_DIVX & MS10 VIFP
F2
W1
A_RXCN
VIFM
G2
A_RX0P
G3
V2
A_RX0N
IP
H3
V1
A_RX1P
IM
G1
A_RX1N
H1
Y2
A_RX2P
SSIF/SIFP
H2
Y1
A_RX2N
SSIF/SIFM
F5
DDCDA_DA/GPIO24
F4
U3
DDCDA_CK/GPIO23
QP
E6
V3
HOTPLUGA/GPIO19
QM
D3
C1
D1
D2
E2
E3
F3
E1
D4
E4
D5
B_RXCP
B_RXCN
B_RX0P
B_RX0N
B_RX1P
B_RX1N
B_RX2P
B_RX2N
DDCDB_DA/GPIO26
DDCDB_CK/GPIO25
HOTPLUGB/GPIO20
AA2
AA1
AB1
AA3
AB3
AB2
AC2
AC1
AB4
AA4
AC3
C_RXCP
C_RXCN
C_RX0P
C_RX0N
C_RX1P
C_RX1N
C_RX2P
C_RX2N
DDCDC_DA/GPIO28
DDCDC_CK/GPIO27
HOTPLUGC/GPIO21
A2
A3
B3
A1
B1
B2
C2
C3
B4
C4
E5
D6
D_RXCP
D_RXCN
D_RX0P
D_RX0N
D_RX1P
D_RX1N
D_RX2P
D_RX2N
DDCDD_DA/GPIO30
DDCDD_CK/GPIO29
HOTPLUGD/GPIO22
CEC/GPIO5
G5
G6
K1
L3
K3
K2
J3
J2
J1
HSYNC0
VSYNC0
RIN0P
RIN0M
GIN0P
GIN0M
BIN0P
BIN0M
SOGIN0
G4
H6
K5
K4
J4
K6
H4
J6
J5
HSYNC1
VSYNC1
RIN1P
RIN1M
GIN1P
GIN1M
BIN1P
BIN1M
SOGIN1
H5
N3
N2
M2
M1
L2
L1
M3
HSYNC2
RIN2P
RIN2M
GIN2P
GIN2M
BIN2P
BIN2M
SOGIN2
N4
N6
L4
L5
L6
M4
M5
K7
CVBS0P
CVBS1P
CVBS2P
CVBS3P
CVBS4P
CVBS5P
CVBS6P
CVBS7P
M6
M7
CVBS_OUT1
CVBS_OUT2
N5
VCOM0
PIN NAME
MODEL_OPT_0
MODEL_OPT_1
MODEL_OPT_2
MODEL_OPT_3
MODEL_OPT_4
MODEL_OPT_5
MODEL_OPT_6
MODEL OPTION
PIN NO.
G19
C5
F7
B6
E18
D18
F9
HIGH
FRC
MINI LVDS
DDR_512MB
FHD
100/120Hz LVDS
GIP
OLED
Y5
IFAGC
RF_TAGC
Y4
U1
TGPIO0/UPGAIN
TGPIO1/DNGAIN
TGPIO2/I2C_CLK
TGPIO3/I2C_SDA
U2
R3
T3
T2
XTALIN
XTALOUT
T1
G14
SPDIF_IN/GPIO177
SPDIF_OUT/GPIO178
G13
B7
DM_P0
DP_P0
A7
AF17
DM_P1
DP_P1
AE17
F14
I2S_IN_BCK/GPIO175
I2S_IN_SD/GPIO176
I2S_IN_WS/GPIO174
F13
F15
D20
I2S_OUT_BCK/GPIO181
I2S_OUT_MCK/GPIO179
I2S_OUT_SD/GPIO182
I2S_OUT_SD1/GPIO183
I2S_OUT_SD2/GPIO184
I2S_OUT_SD3/GPIO185
I2S_OUT_WS/GPIO180
E20
D19
F18
E18
D18
E19
N1
LINE_IN_0L
LINE_IN_0R
LINE_IN_1L
LINE_IN_1R
LINE_IN_2L
LINE_IN_2R
LINE_IN_3L
LINE_IN_3R
LINE_IN_4L
LINE_IN_4R
LINE_IN_5L
LINE_IN_5R
P3
P1
P2
P4
P5
R6
T6
U5
V5
U6
V6
U4
LINE_OUT_0L
LINE_OUT_2L
LINE_OUT_3L
LINE_OUT_0R
LINE_OUT_2R
LINE_OUT_3R
W3
W4
V4
Y3
W5
TP7301
TP7302
TP7303
TP7304
C7333 2.2uF
C7334 2.2uF
C7335 2.2uF
C7336 2.2uF
C7337 2.2uF
C7338 2.2uF
C7339 2.2uF
C7340 2.2uF
C7341 2.2uF
C7342 2.2uF
C7343 2.2uF OPT
C7344 2.2uF OPT
TP7307
TP7308
TP7309
R4
MIC_DET_IN
T5 C7331OPT 2.2uF
MICCM
R5 C7332 2.2uF
MICIN
OPT
T4
AUCOM
VRM
LOW
NO FRC
LVDS
DDR_256MB
HD
50/60Hz LVDS
NON_GIP
LCD
P7
R7
VAG
VRP
P6
R1
HP_OUT_1L
HP_OUT_1R
R2
E21
ET_RXD0
ET_TXD0
E22
D21
ET_RXD1
ET_TXD1
F21
E23
ET_REFCLK
ET_TX_EN
ET_MDC
ET_MDIO
ET_CRS
D22
F22
D23
F23
F8
AVLINK
IRINT
TESTPIN
RESET
U3_RESET
G8
K8
A4
Y17
TP7306
R7349
1M
R7353 100
C7345
4.7uF
R7352 0 OPT
R7355 0 OPT
C7346
1uF
OPT
R7354 100
Close to MSTAR
R7361 100 C7353 0.1uF
R7362 100 C7354 0.1uF
+3.3V_Normal
L7300
BLM18PG121SN1D
X7300
24MHz
NEC_SDA
COMP2_DET
NEC_SCL
C7347
0.1uF
C7348 0.1uF R7364 47
C7349 0.1uF R7365 47
MODEL_OPT_4
MODEL_OPT_5
C7352
10uF
IR
R7363
C7355
0.1uF
L7301
BLM18SG121TN1D
10K
OPT
C7357
1000pF
R7366
1K
TP7305
R7350 0
R7351 0
DEMOD_OPT R7359
DEMOD_OPT R7360
AMP_SCL
AMP_SDA
22
22
TU/DEMOD_I2C
DEMOD_SCL
DEMOD_SDA
TU_SCL
TU_SDA
CM2012F5R6KT
L7315 5.6uH
ANALOG SIF
Close to MSTAR
C7350 27pF
C7351 27pF
L7316 5.6uH C7417
CM2012F5R6KT
4.7uF
10V
R7370
10K
SC1/COMP1_L_IN
SC1/COMP1_R_IN
AV_L_IN
AV_R_IN
SIDEAV_L_IN
SIDEAV_R_IN
COMP2_L_IN
COMP2_R_IN
PC_L_IN
PC_R_IN
AMP_SDA
SIDE_USB_DM
SIDE_USB_DP
SIDE USB
C7418
4.7uF
10V
SOC_RESET
SPDIF_OUT
DTV_IF
IF_P_MSTAR
IF_N_MSTAR
C7359
0.022uF
16V
TU_SIF
Close to MSTAR
AUDIO IN
AUD_SCK
AUD_MASTER_CLK
AUD_LRCH
AMP_SCL
AUD_LRCK
SCART1_Lout
SCART1_Rout
H/P OUT
HP_LOUT
HP_ROUT
I2S_I/F
AUDIO OUT
+1.26V_VDDC
IF_AGC_MAIN
+3.3V_Normal
VDD33_DVI:163mA
+3.3V_Normal VDD33_DVI
+1.26V_VDDC
L7302
BLM18SG700TN1D
L7304
BLM18PG121SN1D
VDD33
L7305
BLM18PG121SN1D
+2.5V_Normal
+2.5V_Normal
+1.5V_DDR
L7306
C7366
L7303
BLM18SG700TN1D
C7364 10uF
10uF
C7361
VDD33
L7308
BLM18PG121SN1D
MIU1VDDC
C7367 0.1uF
10uF
C7362
10uF
C7363
AVDD2P5
L7307
BLM18PG121SN1D
C7365 0.1uF
AU25
C7368 0.1uF
AVDD_DDR0
C7372 0.1uF
10uF
BLM18PG121SN1D
C7369
10uF C7370 10uF
C7374
0.1uF
C7373 10uF C7376
C7375 10uF
C7380
0.1uF
0.1uF
C7382
C7381 10uF
C7384
C7379 0.1uF
C7378 0.1uF
0.1uF
0.1uF
C7386
C7385 0.1uF
C7388
0.1uF
0.1uF
C7389 0.1uF
C7420
0.1uF
C7394
C7392 0.1uF
AVDD_MEMPLL:24mA
L7314
BLM18PG121SN1D
C7371
10uF
AVDD_LPLL
C7419
0.1uF
C7413
0.1uF
Normal 2.5V
AU25:10mA
RSDS Power OPT
AVDD_DDR0:55mA
C7414
0.1uF
C7377 0.1uF
AVDD_DMPLL
L7310
BLM18PG121SN1D
0.1uF
AVDD2P5
+2.5V_Normal
L7311
BLM18PG121SN1D
AVDD_DDR0
5%
1/10W
AVDD_DDR0
R7375
1K
R7376
1K
C7383 0.1uF
VDD33
R7373
0
1/10W
5%
C7397
+1.26V_VDDC
C7398 0.1uF
R7374 0
1/16W
1%
1/16W
1%
C7387 0.1uF
Normal Power 3.3V
VDD33_T/VDDP/U3_VD33_2:47mA
AU33:31mA
090916 modified
C7391 0.1uF
L7309
BLM18PG121SN1D
C7395
0.1uF
10uF
C7401
C7402 0.1uF
ADC2P5
C7404 0.1uF
AVDD25_PGA
10uF
C7406
C7415
L7313
BLM18SG700TN1D
C7416 10uF
0.1uF
C7407 0.1uF
C7405 0.1uF
0.1uF
C7408
C7396 0.1uF
AU33
AVDD_DMPLL/AVDD_NODIE:7.362mA
AVDD2P5/ADC2P5:162mA
AVDD25_PGA:13mA
DDR3 1.5V
VDDC 1.26V
0.1uF
C7409
MVREF
MIU0VDDC
C7390 0.1uF
C7400 0.1uF
C7393
0.1uF
AVDD_DDR1:55mA
0.1uF
C7410
C7403 0.1uF
C7399 0.1uF
AVDD_DDR1
0.1uF
IC101
VDDCLGE107D
(S7M Divx_Non RM)
090:AI26
VDDC
S7M_DIVX & MS10
MIU0VDDC
MIU1VDDC
C7412 1uF
ADC2P5
AU25
AVDD2P5
AVDD2P5
AVDD25_PGA
AVDD_DMPLL
VDD33_DVI
AVDD_DMPLL
AU33
VDD33
AVDD_LPLL
090916 modified
VDD33
C7411
0.1uF
AVDD_DDR0
AVDD_DDR1
MVREF
H11
H12
H13
H14
H15
J12
J13
J14
J15
J16
L18
H16
K19
L19
M18
M19
N18
N19
N20
P18
P19
P20
Y12
J11
L7
H7
J7
J8
L8
W15
Y15
U8
M8
N9
P9
N8
P8
T7
U7
T9
R8
R9
T8
V20
W20
U19
U20
V19
W19
U18
T20
Y14
R19
W14
D15
D16
E15
E16
E17
F16
F17
G16
G17
H17
AB11
AB12
AC11
AC12
AA12
G15
Y7
Y8
VDDC_1
VDDC_2
VDDC_3
VDDC_4
VDDC_5
VDDC_6
VDDC_7
VDDC_8
VDDC_9
VDDC_10
VDDC_11
A_DVDD
B_DVDD
FRC_VDDC_0
FRC_VDDC_1
FRC_VDDC_2
FRC_VDDC_3
FRC_VDDC_4
FRC_VDDC_5
FRC_VDDC_6
FRC_VDDC_7
FRC_VDDC_8
U3_DVDD_DDR
AVDD1P2
DVDD_NODIE
AVDD2P5_ADC_1
AVDD2P5_ADC_2
AVDD25_REF
AVDD_AU25
PVDD_1
PVDD_2
AVDD25_PGA
AVDD_NODIE
AVDD_DVI_1
AVDD_DVI_2
AVDD3P3_CVBS
AVDD_DMPLL
AVDD_AU33
AVDD_EAR33
AVDD33_T
VDDP_1
VDDP_2
VDDP_3
FRC_VD33_2_1
FRC_VD33_2_2
FRC_AVDD_RSDS_1
FRC_AVDD_RSDS_2
FRC_AVDD_RSDS_3
FRC_AVDD
FRC_AVDD_LPLL
FRC_AVDD_MPLL
FRC_VDD33_DDR
AVDD_MEMPLL
FRC_AVDD_MEMPLL
AVDD_DDR0_D_1
AVDD_DDR0_D_2
AVDD_DDR0_D_3
AVDD_DDR0_D_4
AVDD_DDR0_C
AVDD_DDR1_D_1
AVDD_DDR1_D_2
AVDD_DDR1_D_3
AVDD_DDR1_D_4
AVDD_DDR1_C
FRC_AVDD_DDR_D_1
FRC_AVDD_DDR_D_2
FRC_AVDD_DDR_D_3
FRC_AVDD_DDR_D_4
FRC_AVDD_DDR_C
MVREF
NC_1
NC_2
GND_1
GND_2
GND_3
GND_4
GND_5
GND_6
GND_7
GND_8
GND_9
GND_10
GND_11
GND_12
GND_13
GND_14
GND_15
GND_16
GND_17
GND_18
GND_19
GND_20
GND_21
GND_22
GND_23
GND_24
GND_25
GND_26
GND_27
GND_28
GND_29
GND_30
GND_31
GND_32
GND_33
GND_34
GND_35
GND_36
GND_37
GND_38
GND_39
GND_40
GND_41
GND_42
GND_43
GND_44
GND_45
GND_46
GND_47
GND_48
GND_49
GND_50
GND_51
GND_52
GND_53
GND_54
GND_55
GND_56
GND_57
GND_58
GND_59
GND_60
GND_61
GND_62
GND_63
GND_64
GND_65
GND_66
GND_67
GND_68
GND_69
GND_70
GND_71
GND_72
GND_73
GND_74
GND_75
GND_76
GND_77
GND_78
GND_79
GND_80
GND_81
GND_82
GND_83
GND_84
GND_85
GND_86
GND_87
GND_88
GND_89
GND_90
GND_91
GND_92
GND_93
GND_94
GND_95
GND_96
GND_97
GND_98
GND_99
GND_100
GND_101
GND_102
GND_103
GND_104
GND_105
GND_106
GND_107
GND_108
GND_109
GND_110
GND_FU
PGA_VCOM
G18
H9
H10
H18
H19
J10
J17
J18
J19
K9
K10
K11
K12
K13
K14
K15
K16
K17
K18
L9
L10
L11
L12
L13
L14
L15
L16
L17
M9
M10
M11
M12
M13
M14
M15
M16
M17
N10
N11
N12
N13
N14
N15
N16
N17
P10
P11
P12
P13
P14
P15
P16
P17
R10
R11
R12
R13
R14
R15
R16
R17
R18
T10
T11
T12
T13
T14
T15
T16
T17
T18
T19
U10
U11
U12
U13
U14
U15
U16
U17
V7
V8
V9
V10
V11
V12
V13
V14
V15
V16
V17
V18
W7
W8
W9
W10
W11
W12
W13
W16
W17
W18
Y13
Y18
AA13
AB13
AC13
D17
H23
AF13
J9 L7312
U9 BLM18SG121TN1D
GP2_Saturn7M
MAIN_2
VDDC : 2026mA
Ver. 1.4
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
90

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
AE8
IC101
LGE107D (S7M Divx_Non RM)
S7M_DIVX & MS10
AE1
AF16
AF1
AE3
AD14
AD3
AF15
AF2
AE15
AD2
AD16
AD15
AE16
FRC_DDR3_A0/DDR2_NC
FRC_DDR3_A1/DDR2_A6
FRC_DDR3_A2/DDR2_A7
FRC_DDR3_A3/DDR2_A1
FRC_DDR3_A4/DDR2_CASZ
FRC_DDR3_A5/DDR2_A10
FRC_DDR3_A6/DDR2_A0
FRC_DDR3_A7/DDR2_A5
FRC_DDR3_A8/DDR2_A2
FRC_DDR3_A9/DDR2_A9
FRC_DDR3_A10/DDR2_A11
FRC_DDR3_A11/DDR2_A4
FRC_DDR3_A12/DDR2_A8
ACKP/RLV3P/RED[3]
ACKM/RLV3N/RED[2]
A0P/RLV0P/RED[9]
A0M/RLV0N/RED[8]
A1P/RLV1P/RED[7]
A1M/RLV1N/RED[6]
A2P/RLV2P/RED[5]
A2M/RLV2N/RED[4]
A3P/RLV4P/RED[1]
A3M/RLV4N/RED[0]
A4P/RLV5P/GREEN[9]
A4M/RLV5N/GREEN[8]
W26
W25
U26
U25
U24
V26
V25
V24
W24
Y26
Y25
Y24
AC26
AF3
AF14
AD1
AD13
AE14
AE13
AE4
AD5
AF4
AD4
AE2
AF8
AD9
AE9
AF9
AE11
AF6
AE6
AF11
AD6
AD12
AE5
AF12
AF5
AE12
AE10
AF7
AD11
AD7
AD10
AE7
AF10
AD8
BCKP/TCON13/GREEN[1]
BCKM/TCON12/GREEN[0]
B0P/RLV6P/GREEN[7]
FRC_DDR3_BA0/DDR2_BA2
B0M/RLV6N/GREEN[6]
FRC_DDR3_BA1/DDR2_ODT
B1P/RLV7P/GREEN[5]
FRC_DDR3_BA2/DDR2_A12
B1M/RLV7N/GREEN[4]
B2P/RLV8P/GREEN[3]
FRC_DDR3_MCLK/DDR2_MCLK
B2M/RLV8N/GREEN[2]
FRC_DDR3_CKE/DDR2_RASZ
B3P/TCON11/BLUE[9]
FRC_DDR3_MCLKZ/DDR2_MCLKZ
B3M/TCON10/BLUE[8]
B4P/TCON9/BLUE[7]
B4M/TCON8/BLUE[6]
FRC_DDR3_ODT/DDR2_BA1
FRC_DDR3_RASZ/DDR2_WEZ
FRC_DDR3_CASZ/DDR2_CKE
CCKP/LLV3P
FRC_DDR3_WEZ/DDR2_BA0
CCKM/LLV3N
C0P/LLV0P/BLUE[5]
FRC_DDR3_RESETB/DDR2_A3
C0M/LLV0N/BLUE[4]
C1P/LLV1P/BLUE[3]
C1M/LLV1N/BLUE[2]
FRC_DDR3_DQSL/DDR2_DQS0
C2P/LLV2P/BLUE[1]
FRC_DDR3_DQSLB/DDR2_DQSB0
C2M/LLV2N/BLUE[0]
C3P/LLV4P
FRC_DDR3_DQSU/DDR2_DQS1
C3M/LLV4N
FRC_DDR3_DQSUB/DDR2_DQSB1
C4P/LLV5P
C4M/LLV5N
FRC_DDR3_DML/DDR2_DQ7
FRC_DDR3_DMU/DDR2_DQ11
DCKP/TCON5
FRC_DDR3_DQL0/DDR2_DQ6
DCKM/TCON4
FRC_DDR3_DQL1/DDR2_DQ0
D0P/LLV6P
FRC_DDR3_DQL2/DDR2_DQ1
D0M/LLV6N
FRC_DDR3_DQL3/DDR2_DQ2
D1P/LLV7P
FRC_DDR3_DQL4/DDR2_DQ4
D1M/LLV7N
FRC_DDR3_DQL5/DDR2_NC
D2P/LLV8P
FRC_DDR3_DQL6/DDR2_DQ3
D2M/LLV8N
FRC_DDR3_DQL7/DDR2_DQ5
D3P/TCON3
D3M/TCON2
FRC_DDR3_DQU0/DDR2_DQ8
D4P/TCON1
FRC_DDR3_DQU1/DDR2_DQ14
D4M/TCON0
FRC_DDR3_DQU2/DDR2_DQ13
FRC_DDR3_DQU3/DDR2_DQ12
FRC_DDR3_DQU4/DDR2_DQ15 GPIO0/TCON15/HSYNC/VDD_ODD
FRC_DDR3_DQU5/DDR2_DQ9 GPIO1/TCON14/VSYNC/VDD_EVEN
FRC_DDR3_DQU6/DDR2_DQ10
GPIO2/TCON7/LDE/GCLK4
FRC_DDR3_DQU7/DDR2_DQM1
GPIO3/TCON6/LCK/GCLK2
AC25
AA26
AA25
AA24
AB26
AB25
AB24
AC24
AD26
AD25
AD24
AD23
AE23
AE26
AE25
AF26
AF25
AE24
AF24
AF23
AD22
AE22
AF22
AD19
AE19
AD21
AE21
AF21
AD20
AE20
AF20
AF19
AD18
AE18
AF18
AB22
AB23
AC23
AC22
FRC_DDR3_NC/DDR2_DQM0
Y11
Y19
FRC_REXT
FRC_TESTPIN
AB16
FRC_GPIO0/UART_RX
FRC_GPIO1
FRC_GPIO3
AA14
AC15
Y16
FRC_GPIO8
FRC_GPIO9/UART_TX
FRC_GPIO10
AC16
AC14
AA16
FRC_I2CM_DA
FRC_I2CM_CK
AA15
Y10
FRC_I2CS_DA
FRC_I2CS_CK
AA11
AB15
FRC_PWM0
FRC_PWM1
AB14
RXBCK+
RXBCK-
RXB0+
RXB0-
RXB1+
RXB1-
RXB2+
RXB2-
RXB3+
RXB3-
RXB4+
RXB4-
RXACK+
RXACK-
RXA0+
RXA0-
RXA1+
RXA1-
RXA2+
RXA2-
RXA3+
RXA3-
RXA4+
RXA4-
GP2_Saturn7M Ver. 1.4
DDR3(FRC)
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
92

+12V/+15V
L7910
C7910
10uF
25V
+12V/+15V
L7500
C7500
10uF
25V
NON_Adapter
P7500
SMAW200-12
+15V
1
+15V
2
GND
3
GND
4
+3.5V_ST
5
+3.5V_ST
6
GND
7
OLP
8
INV_ON
9
P_DIM
10
A_DIM
11
NC
12
Adapter
JK7500
JPD003N-M432-4F
Adapter
P7501
SM14B-SRSS-TB
15
24V
1
24V
2
24V
3
24V
4
24V
5
GND
6
GND
7
GND
8
GND
9
GND
10
NC
11
INV_ON
12
PWM_DIM
13
ERROR_OUT
14
GND
24V
SW
GND
R7580
0
OPT
C7506
1uF
6.3V
OPT
C7920
0.1uF
R7850
22
C7504
0.1uF
R7505
4.7K
C7580
68uF
35V
IC7500
MP8706EN-C247-LF-Z
IN
SW_1
SW_2
BST
R7509
10K
R7510
10K
POWER_ON/OFF2_1
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
1
2
3
4
C7502
0.1uF
50V
R7579
A_DIM
0
Adapter_LGD
8
7
6
5
GND
VCC
FB
C7507
1uF
6.3V
OPT
IC7511
MP8706EN-C247-LF-Z
SW_1
SW_2
R7502
22 1/10W
C7927
0.1uF
50V
IN
BST
+24V_LED_driver
Adapter_AUO
R7587
R7541 0
Adapter_LGD
1
2
3
4
0
C7928
0.01uF
50V
L7911
3.6uH
L7501
3.6uH
R7549
0
Adapter_AUO
To Tuner
3A
NR8040T3R6N
NR8040T3R6N
8
7
6
5
GND
VCC
FB
EN/SYNC
+5V_USB
3A
EN/SYNC
C7921
1uF
50V
R7851
10K
R7852
10K
C7508
1uF
50V
MLB-201209-0120P-N2 Adapter
C7509
0.1uF
16V
0 R7506
0 R7507
OPT
0 R7508
L7502
MLB-201209-0120P-N2
NON_Adapter NON_Adapter
OPT
OPT
C7913
100pF
50V
POWER_ON/OFF2_2
090916
OPT
C7510
100pF
50V
090916
L7503
MLB-201209-0120P-N2
NON_Adapter C7511
0.1uF
16V
PWM_DIM
OPC_OUT
OPC_OUT
NON_Adapter
R7853
33K
R7854
6.2K
R7512
33K
R7513
6.2K
1%
1%
R7511
6.8K
OPT
L7504
+3.3V_Normal
C
E
MAX 300mA
OPT
C7914
100pF
R1 50V
1%
1%
R2
OPT
C7512
100pF
R1 50V
+3.5V_ST
C7516
0.1uF
16V
+24V/+15V
OLP
3.3K -> 1K (threshold voltage up)
+3.5V_ST
R7514
1K
C7513
22uF
10V
C7514
0.1uF
50V
B
ERROR_OUT
C7915
22uF
10V
R7515
10K
Q7502
2SC3052
C7918
0.1uF
16V
Vout=(1+R1/R2)*0.8
MAX 2000mA
R2
Vout=(1+R1/R2)*0.8
C7517
68uF
35V
C7515
68uF
35V
NON_Adapter
R7516
10K
+5V_General
+5V_USB
C7919
0.1uF
16V
C7518
0.1uF
16V
R7517
10K
OPT
INV_CTL
+24V_LED
Adapter
L7912
MLB-201209-0120P-N2
L7505
PANEL_CTL
+5V_Normal
5V_PANEL
R7500
10K
Adapter
POWER_ON/OFF2_2
R7832
10K
+3.5V_Normal
C7553
0.1uF
16V
B
+3.5V_ST
C7520
22uF
10V
+12V/+15V +24V/+15V
12V_PANEL
PANEL_POWER 24V-->3.48V
15V-->3.56V
C
E
OPT
R7522
10K
R7521
10K B
+24V/+15V
AO3407A Vgs : 10.8V(24V input)
AO3407A Vgs : 8.3V(15V input)
C7501
0.1uF
50V
L7517
4A -> 3A modify 090916
+3.5V_ST
Placed on SMD-TOP
NON_Adapter
RL_ON
C IN
C IN
C7572
22uF
10V
C7503
2.2uF
50V
R7501
27K
Q7500
L7507
L7506
R7503
22K
G
Q7501
AO3407A
IC7505
AZ2940D-2.5TRE1
3 VOUT
VIN 1 Vd=550mV
2
GND
S
D
C
E
R7552
1
R7524
75K
1/8W
1%
R7523
22K
Q7503
2SC3052
R7574
11K
5%
C7505
0.01uF
50V
C7556
10uF
10V
C7525
0.01uF
25V
5V_PANEL
R7530-*1
22K
5V_PANEL
R7531-*1
2.7K
+2.5V_Normal
FB
GND
IN
BS
C7557
0.1uF
16V
B
R7527
22K
AMP_VCC
IC7501
MP2212DN
1
2
3
4
FB
GND
IN
BS
C7526
0.1uF
16V
R7528
C7573
100pF
50V
E
IC7504
MP2212DN
1
2
3
4
L7913
CPI2520NHL3R3ME
Adapter
L7914
BLM18PG121SN1D
NON_Adapter
1608 2A
C7932
3.3uF
50V
R7576
10
1%
C7528
100pF
50V
10
1/10W
1%
R7533
8
7
6
5
22K 1%
C7529
10uF
16V
OPT
R7531
5.6K
12V_PANEL
C
R7572
0
Q7505
2SC3052
8
7
6
5
R7577 0
NON_Adapter
C7933
0.01uF
50V
+15V Control
300 mA
Placed on SMD-TOP
R2
R7530
33K
12V_PANEL
EN/SYNC
SW_2
SW_1
VCC
VCC
R7575
10K 1%
EN/SYNC
SW_2
SW_1
R7536
C7530
1uF
10V
C7531
4.7uF
16V
C7574
1uF
10V
+3.5V_ST
+12V/+15V
24K 1%
R7532
0
10K
R7578
Q7506
AO3407A
C7534
0.1uF
50V
C7575
0.1uF
50V
C7554
0.01uF
POWER_ON/OFF2_2
R7545
10K
10K
R7539
L7510
3.6uH
C7541
1uF
25V
OPT
S7 DDR 1.5V
R2
AO3407A Vgs : 10.8V
+2.5V
Replaced Part
3A
3A
Replaced Part
R1
Close to IC
RL_ON
R1
Close to IC
+24V_LED
C7924
0.1uF
50V
Adapter
R7860
10K
S
Adapter
G
D
L7516
3.6uH
R7551
22K
C7925
2.2uF
50V
Adapter
R7861
27K
Adapter
B
NR8040T3R6N
C7555
0.1uF
B
C
New item
POWER_ON/OFF1
R7555
10K
C
E
R7862
22K
Adapter
Q7521
Adapter
AO3407A
Q7520
Adapter
E
Q7507
2SC3052
C7546
22uF
10V
C7576
22uF
10V
R7556
0
Vout=0.8*(1+R1/R2)
G
S
D
Adapter
C7559
4.7uF
16V
C7926
0.01uF
50V
PANEL_VCC
POWER_ON/OFF2_1
C7547
0.1uF
16V
1074 mA
Q7508
AO3407A
S
G
+1.5V_DDR
C7577
0.1uF
Placed on SMD-TOP
D
+1.26V_VDDC
C7548
0.1uF
Placed on SMD-TOP
2026 mA
Vout=0.8*(1+R1/R2)
+3.5V_Normal
C7561
1uF
25V
C7568
0.1uF
16V
+3.5V_Normal
+24V_LED_driver
AO3407A Vgs : 10.8V
LED Driver Power
S7 core 1.26V volt
ST_3.5V-->3.5V --> 3.375V
+12V/+15V
L7512
Adapter
C7519
1uF
25V
Adapter
L7511
C7549 C7551
10uF 10uF
25V 25V
+12V/+15V
18K
R7570
C7550
10uF
25V
IC7509-*1
G691L293T73UF
VCC 3
1
GND
DEV_Repalcement
IC7510-*1
G691L293T73UF
VCC 3
1
GND
Adapter
C7552
10uF
25V
C7522
1uF
50V
2 RESET
2 RESET
DEV_Repalcement
S1
1
S2
2
S3
3
G
4
Adapter
Q7504
Si4800BDY
MBRA340T3G
close to pin
Adapter
Adapter
R7525
68K
Adapter
PGND
VIN
2
C7923
0.1uF
50V AGND
3
FB
D8
8
D7
7
D6
6
D5
5
1/16W
5%
R7548
5.1K
Adapter
5%
IC7506
AOZ1073AIL
1
4
R7547
30K
Power_DET
Adapter
5%
1/10W
22
R7519
close to IC7502
$0.12
C7524
220pF
50V
BST
VCC
Adapter
1%
PGND
VIN
2
C7922
0.1uF
50V AGND
3
FB
+3.5V_ST
1%
1/16W
1%
1/16W
C7527 Adapter
50V 0.1uF
IC7503
MP4460DQ-LF-Z EP_GND
8
7
6
5
Adapter
R7529
100K
THERMAL
11
Adapter
L7509
3.6uH
NR8040T3R6N
LX_2
LX_1
EN
COMP
IC7507
AOZ1072AI
1
4
R7547-*1
18K
1K
R7583
27K
R7584
SW_1
1
SW_2
2
D7500
EN
3
COMP
4
FB
5
1%
LIPS
R7548-*1
5.6K
1%
LIPS
LIPS
LIPS
IC7502
MP8670DN-LF-Z
SW
BG
1
2
3
4
3A
Adapter
$0.37
Adapter
L7508
4.7uH
SP-7850_4.7
Adapter
$0.21
8
7
6
5
IN
EN/SYNC
FB
R2
GND
BST
10
VIN_2
9
VIN_1
8
FREQ
7
GND
6
POWER_ON/OFF2_2
R7558
10K
9.1K
R7557
8
7
6
5
LX_2
LX_1
EN
COMP
Adapter Adapter Adapter
C7533 C7536 C7540
0.1uF 3.3uF 3.3uF
50V 50V 50V
1%
1%
1/8W
Adapter
C7532
10uF
25V
Adapter
Adapter
+3.3V_Normal
L7513
3.6uH
NR8040T3R6N
2200pF
C7558
Adapter
R7537
200K
1/8W
1%
1.6K 6.8K
R7581 R7538
Adapter Adapter
22
R7571
C7538
10uF
10V
+5V_Normal
2A
POWER_SMALL
12K
R7559
R7562
27K
R7563
4.7K
R7564
10K
1%
1%
L7514
3.6uH
OPT
C7562
100pF
50V
NR8040T3R6N
POWER_ON/OFF2_2
R7560
10K
R7561
100K
IC7509
NCP803SN293
VCC 3
2 RESET
1
GND
+24V/+15V
Adapter
C7537
10uF
25V
Adapter C7542
3.3uF
50V
Adapter
2200pF
C7560
R7585
100K LIPS
Adapter
R7540
120K
C7571
10uF
10V
1%
NCP
IC7510
NCP803SN293
VCC 3
2 RESET
1
GND
Vout=0.8*(1+R1/R2)
R1
Placed on SMD-TOP
NCP
1%
OPT
22K
R7542
Adapter
1%
1/10W
Adapter
R7565
51K
R7566
1.5K
R7567
10K
C7543
0.1uF
50V
5%
1%
C7563
22uF
10V
C7565
100pF
50V
1%
Adapter
C7545
0.1uF
50V
+24V/+15V
RL_ON
Adapter
C7544
0.1uF
50V
30K
R7543
1934 mA
1%
R7582
100
LIPS
1%
R7586
100
+3.5V_ST
R7569
10K
Replacement Item
Adapter
R7544
105K
1/10W
1%
C7566
22uF
10V
OPT
+12V/+15V
+3.5V_ST
L7515
CIC21J501NE
C7567
0.1uF
16V
POWER_DET
+3.3V_Normal
C7578
0.1uF
16V
C7569
0.1uF
16V
+5V_Normal
GP2_Saturn7 Ver. 1.00
R1
R2
Vout=(1+R1/R2)*0.8
MAX 1A
R1
R2
UNDER CHECKING
24V->15V
090916
24V->3.5V
Switching noise reducing [MPS recommend]
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
92
real output : 12.3V
C7570
0.1uF
16V

CONTROL
IR & LED
KEY1
KEY2
IR
R7600
100
R7601
100
R7602
22
+3.5V_ST
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
R7605
10K
1%
R7604
47K
Q7600
2SC3052
+3.5V_ST
C
E
B
R7603
0
OPT
R7606
10K
1%
R7607
10K
L7600
BLM18PG121SN1D
R7608
47K
Q7601
2SC3052
L7601
BLM18PG121SN1D
+3.5V_ST
C
E
B
R7609
47K
R7610
3.3K
OPT
C7600
0.1uF
16V
+3.5V_ST
C7601
0.1uF
16V
5.6V
COMMERCIAL
D7600
5.6V
L7602
BLM18PG121SN1D
L7603
BLM18PG121SN1D
+3.5V_ST
+3.5V_ST
C7602
0.1uF
+3.5V_ST
R7613
47K
R7611 Commercial_EU
Commercial
22
IR_OUT
R7615
Commercial
47K
R7614
Q7602 C 10K
2SC3052 B
Commercial_EU E Commercial_EU
C
B
Q7603 E
2SC3052
Commercial
D7601
R7612
0
Commercial_US
C7603
0.1uF
D7602
5.6V
AMOTECH
L7604
BLM18PG121SN1D
C7604
0.1uF
16V
R7616
47K
P7600
12507WR-03L
1
2
3
4
Commercial
C7605
1000pF
50V
D7603
5.6V
AMOTECH
LED_B/LG_LOGO
+3.3V_Normal
L7605
BLM18PG121SN1D
C7606
0.1uF
16V
NEC_EEPROM_SCL
NEC_EEPROM_SDA
EYEQ/TOUCH_KEY
R7618
100
EYEQ/TOUCH_KEY
R7619
100
R7617
100
C7608
100pF
50V
LED_R/BUZZ
C7607
1000pF
50V
C7609
1000pF
50V
OPT
C7610
1000pF
50V
OPT
R7620 1.5K
D7604
CDS3C05HDMI1
5.6V
OPT
C7611
0.1uF
16V
D7606
5.6V
AMOTECH
R7621
1.5K
D7605
CDS3C05HDMI1
5.6V
OPT
R7622
10K
Zener Diode is
close to wafer
12PIN_ANGLE
P7601
12507WR-12L
1
2
3
4
5
6
7
8
9
10
11
12
GP2_Saturn7M
IR & LED
13
12PIN_STRAIGHT
P7601-*1
12507WS-12L
1
2
3
4
5
6
7
8
9
10
11
12
13
Ver. 1.2
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
6

HDMI_1
HDMI_2
HDMI_1
20
$0.253
19
EAG59023302
EAG59023302
SHIELD
SHIELD
20
$0.253
19
JK7701
18
17
16
15
14
13
12
JK7700
18
17
16
15
14
13
12
HDMI_2
11
CK+
10
D0-
9
D0_GND
8
D0+
7
D1-
6
D1_GND
5
D1+
4
D2-
3
D2_GND
2
D2+
1
5V_HDMI_1
11
CK+
10
D0-
9
D0_GND
8
D0+
7
D1-
6
D1_GND
5
D1+
4
D2-
3
D2_GND
2
D2+
1
R7700
1K
R7701
1.8K
R7702
1K
R7703
1.8K
D7700
5V_HDMI_2
D7701
5V_DET_HDMI_1
R7704
3.3K
R7705
C7701
0.1uF
16V
C7700
0.1uF
16V
R7717 22
JP7700
R7718 22
JP7701
R7719 100
R7722 0
R7723 0
R7727 0
JP7702
R7706 22
R7707 22
JP7703
R7708 100
R7710 0
R7716 0
Q7700
2SC3052
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
3.3K
5V_DET_HDMI_2
R7720 0
R7721 0
R7724 0
R7725 0
R7726 0
R7709 0
R7711 0
R7712 0
R7713 0
R7714 0
R7715 0
Q7701
2SC3052
C
E
C
E
B
B
R7728
10K
R7729
10K
HPD1
DDC_SDA_1
DDC_SCL_1
HDMI_CEC
CK-_HDMI1
CK+_HDMI1
D0-_HDMI1
D0+_HDMI1
D1-_HDMI1
D1+_HDMI1
D2-_HDMI1
D2+_HDMI1
HPD2
DDC_SDA_2
DDC_SCL_2
HDMI_CEC
CK-_HDMI2
CK+_HDMI2
D0-_HDMI2
D0+_HDMI2
D1-_HDMI2
D1+_HDMI2
D2-_HDMI2
D2+_HDMI2
SIDE_HDMI
HDMI_SIDE
EAG42463001
JACK_GND
20
$0.253
19
18
17
16
15
14
13
12
JK7702
11
CK+
10
D0-
9
D0_GND
8
D0+
7
D1-
6
D1_GND
5
D1+
4
D2-
3
D2_GND
2
D2+
1
HDMI_CEC
5V_HDMI_4
R7730
1K
R7731
1.8K
D7702
R7732
3.3K
5V_DET_HDMI_4
D7709
AVRL161A1R1NT
D7707
AVRL161A1R1NT
C7702
0.1uF
16V
JP7705
OPT
OPT
JP7704
R7733 22
R7734
R7735 100
D7708
D7703
R7736 0
R7737 0
R7738 0
R7739 0
R7740 0
R7741 0
R7742 0
R7743 0
22
Q7702
2SC3052
C
E
For CEC
S
B
D
G
68K
R7765
R7766
0
OPT
68K
R7745
0
OPT
B
S
B
D
G R7763
R7744
10K
BSS83
Q7704
BSS83
Q7703
+3.3V_Normal
R7767
10K
C7707
0.1uF
16V
R7762
10K
C7706
0.1uF
16V
+3.5V_ST
HPD4
DDC_SDA_4
DDC_SCL_4
HDMI_CEC
CK-_HDMI4
CK+_HDMI4
D0-_HDMI4
D0+_HDMI4
D1-_HDMI4
D1+_HDMI4
D2-_HDMI4
D2+_HDMI4
R7768
68K
OPT
R7764
68K
R7769
0
CEC_ON/OFF
CEC_REMOTE_S7
CEC_REMOTE_NEC
HDMI EEPROM
A0
A1
A2
GND
A0
A1
A2
GND
HDMI_1
IC7700
AT24C02BN-10SU-1.8
HDMI_2
IC7701
AT24C02BN-10SU-1.8
A0
A1
A2
GND
1
2
3
4
1
$0.055 WP
2
7
3
4
HDMI_SIDE
IC7702
AT24C02BN-10SU-1.8
1
2
3
4
$0.055
$0.055
HDMI
8
7
6
5
8
6
5
8
7
6
5
VCC
WP
SCL
SDA
VCC
SCL
SDA
VCC
WP
SCL
SDA
JP7706
R7748 22
R7747 22
JP7707
C7703
0.1uF
C7704
0.1uF
R7750 22
R7749 22
C7705
0.1uF
JP7708
R7751 22
R7752 22
R7753
5V_HDMI_1 +5V_Normal
R7757
R7754
4.7K
R7756 R7760
10K
A2
C
A1
ENKMC2838-T112
D7704
5V_HDMI_2 +5V_Normal
R7755
10K
10K
A2
4.7K
R7759
4.7K
C
A1
4.7K
5V_HDMI_4+5V_Normal
A2
C
R7758 R7761
4.7K 4.7K
EDID_WP
DDC_SCL_1
DDC_SDA_1
ENKMC2838-T112
D7705
A1
EDID_WP
DDC_SCL_2
DDC_SDA_2
ENKMC2838-T112
D7706
EDID_WP
DDC_SCL_4
DDC_SDA_4
GP2_Saturn7M Ver. 1.2
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
94

TP7013
TP7014
TP7016
TP7017
TP7018
TP7019
TP7020
TP7021
TP7022
TP7023
TP7024
TP7025
TP7026
TP7027
TP7028
TP7029
TP7030
MAIN1 BLOCK
5V_DET_HDMI_3
FRC_RESET
SCAN_BLK2
SCAN_BLK1/OPC_OUT
WIRELESS_DL_RX
WIRELESS_DL_TX
/PIF_SPI_CS
ET_RXER
/RST_PHY
M_REMOTE_RX
M_REMOTE_TX
FRC_SCL
FRC_SDA
UART_FRC_RX
UART_FRC_TX
FRC_PWM0
FRC_PWM1
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
MICOM BLOCK
TP7032
TP7033
TP7035
TP7036
WIRELESS_DETECT
WIRELESS_PWR_EN
TP7034 WIRELESS_SW_CTRL
RF_ENABLE
RF_RESET
GP2_Saturn7 Ver. 1.0
TP_SMALL 75
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only

+3.3V_Normal
IC7800
AP1117E18G-13
C7800
0.1uF
16V
IN
INADJ/GND
IC7800-*1
KIA1117ST18
3
OUT
2
OUT
1
Replacement
ADJ/GND
AUD_LRCH
AUD_LRCK
AUD_SCK
AMP_SDA
AMP_SCL
+1.8V_AMP
C7802
10uF
10V
+1.8V_AMP
C7803
0.1uF
16V
AUD_MASTER_CLK
+1.8V_AMP
AMP_RESET_N
R7802 100
R7803 100
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
BLM18PG121SN1D
R7800
1
L7800
OPT
C7801
10uF
10V
BLM18PG121SN1D
L7801
C7804
0.1uF
16V
OPT
C7805
10uF
10V
R7801 100
R7804 33
R7805 33
C7808
1000pF
50V
C7806
100pF
50V
C7807
0.1uF
16V
120 mA
TP7800
C7811
0.1uF
BLM18PG121SN1D
C7810
1000pF
50V
R7806
3.3K
C7809
18pF
50V
+3.3V_Normal
L7802
C7812
18pF
50V
C7813
22pF
50V
OPT
C7814
22pF
50V
OPT
C7819
22000pF
50V
BST1A
C7816
VDR1A
1uF 25V /RESET
1
2
3
AD 4
DGND_1 5
GND_IO 6
CLK_I 7
VDD_IO 8
DGND_PLL 9
AGND_PLL 10
LF 11
AVDD_PLL 12
DVDD_PLL 13
GND 14
+1.8V_AMP
OPT
C7815
10uF
10V
C7818
0.1uF
16V
C7817
22pF
50V
OPT
AMP_VCC
THERMAL
57
IC7801
EAN60969601
NTP-7000
AMP_MUTE_HOTEL
C7820
0.1uF
50V
EP_PAD
PGND1A_2
PGND1A_1
OUT1A_2
OUT1A_1
PVDD1A_2
PVDD1A_1
PVDD1B_2
PVDD1B_1
OUT1B_2
OUT1B_1
PGND1B_2
PGND1B_1
BST1B
VDR1B
56
55
54
53
52
51
50
49
48
47
46
45
44
43
15
16
17
18
19
20
21
22
23
24
25
26
27
28
DGND_2
DVDD
SDATA
WCK
BCK
SDA
SCL
MONITOR0
MONITOR1
MONITOR2
/FAULT
VDR2B
BST2B
PGND2B_1
C7822
1uF
25V
C7821
1000pF
50V
C7824
0.1uF
50V
C7823
22000pF
50V
C7825
1uF
25V
C7826
10uF
35V
42 NC C7827
41 VDR2A 25V1uF
40 BST2A
39 PGND2A_2
38 PGND2A_1
37 OUT2A_2
36 OUT2A_1
35 PVDD2A_2
34 PVDD2A_1
33 PVDD2B_2
32 PVDD2B_1
31 OUT2B_2
30 OUT2B_1
29 PGND2B_2
R7807
0
OPT
C7828
22000pF
50V
OPT
R7809
3.3
C7829
22000pF
50V
R7808 100
R7810
10K
C
Q7800
2SC3052
OPT
C7831
0.01uF
50V
C7830
0.1uF
50V
+3.5V_ST
E
AMP_VCC
POWER_DET
B
C7832
0.1uF
50V
R7811
10K
D7800
1N4148W
100V
OPT
D7801
1N4148W
100V
OPT
D7802
1N4148W
100V
OPT
D7803
1N4148W
100V
OPT
C7833
10uF
35V
R7812
12
C7834
390pF
50V
C7835
390pF
50V
R7813
12
R7814
12
C7836
390pF
50V
C7837
390pF
50V
R7815
12
AMP_MUTE
R7819
12
R7817
12
R7818
12
R7816
12
L7804
AD-8770
2S
2F
1S 1F
15uH
L7803
AD-8770
2S
2F
1S 1F
15uH
C7838
0.47uF
50V
C7839
0.47uF
50V
C7840
0.1uF
50V
C7841
0.1uF
50V
C7842
0.1uF
50V
C7843
0.1uF
50V
SPK_L+
SPK_L-
SPK_R+
SPK_R-
R7820
4.7K
R7821
4.7K
R7822
4.7K
R7823
4.7K
C7844 OPT
0.01uF
50V
R7828OPT
3.3
R7829OPT
3.3
C7845 OPT
0.01uF
50V
C7846 OPT
0.01uF
50V
R7830OPT
3.3
R7831OPT
3.3
C7847 OPT
0.01uF
50V
R7824
0
R7825
0
R7826
0
R7827
0
SPK_L+
SPK_L-
SPK_R+
SPK_R-
WAFER-ANGLE
4
3
2
1
P7800
2.5mm -> 2.0mm changed
GP2_Saturn7M Ver. 1.1
AUDIO[NTP]
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
SPEAKER_L
SPEAKER_R
96

[51Pin LVDS Connector]
(For FHD 60Hz)
P7900
TF05-51S
FHD
52
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
PANEL_VCC
L7900
120-ohm
FHD
R7900 0
EXCEPT_LGD_22
R7901 0
EXCEPT_LGD_22
C7900
10uF
16V
OPT
must be located Bottom side
C7901
1000pF
50V
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
RXA4-
RXA4+
RXA3-
RXA3+
RXACK-
RXACK+
RXA2-
RXA2+
RXA1-
RXA1+
RXA0-
RXA0+
RXB4-
RXB4+
RXB3-
RXB3+
RXBCK-
RXBCK+
RXB2-
RXB2+
RXB1-
RXB1+
RXB0-
RXB0+
C7902
0.1uF
16V
R7910
10K
BIT_SEL_LOW
+3.3V_Normal
R7911
3.3K
LVDS_SEL_HIGH
R7912
10K
LVDS_SEL_LOW
[30Pin LVDS Connector]
(For HD 60Hz_Small)
P7903
FF10001-30
30PIN_FHD
31
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
C7912
10uF
16V
OPT
RXA3-
RXA3+
RXA2-
RXA1-
RXA0-
PANEL_VCC
C7911
1000pF
50V
30PIN_FHD
RXACK-
RXACK+
RXA2+
RXA1+
RXA0+
RXB3-
RXB3+
RXBCK-
RXBCK+
RXB2-
RXB2+
RXB1-
RXB1+
RXB0-
RXB0+
30PIN_FHD
L7904
120-ohm
30PIN_FHD
C7909
0.1uF
16V
[30Pin LVDS Connector]
(For HD 60Hz_Normal)
P7901
FF10001-30
HD_60Hz_NORMAL
31
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
R7915 0
HD_60Hz_NORMAL
R7916 0
OPT
R7917 0
OPT
R7913 0
OPT
R7914 0
HD_60Hz_NORMAL
SMALL_NC1
SMALL_NC2
SMALL_OPC_OUT
PWM_DIM
OPC_OUT
RXA3-
RXA3+
RXACK-
RXACK+
RXA2-
RXA2+
RXA1-
RXA1+
RXA0-
RXA0+
OPC_EN
+3.3V_Normal
SMALL_OPC_EN
SMALL_NC3
SMALL_NC4
R7919
3.3K
LVDS_SEL_HIGH
R7920
10K
LVDS_SEL_LOW
C7905
10uF
16V
OPT
C7904
1000pF
50V
PANEL_VCC
L7901
120-ohm
HD_60Hz_NORMAL
HD_60Hz_NORMAL
HD_60Hz_NORMAL
C7903
0.1uF
16V
[30Pin LVDS Connector]
(For HD 60Hz_Small)
P7902
FF10001-30
HD_60Hz_SMALL
31
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
GP2_Saturn7M
C7908
10uF
16V
OPT
C7907
1000pF
50V
SMALL_NC1
SMALL_NC2
SMALL_OPC_OUT
RXA3-
RXA3+
RXACK-
RXACK+
RXA2-
RXA2+
RXA1-
RXA1+
RXA0-
RXA0+
SMALL_OPC_EN
SMALL_NC3
SMALL_NC4
PANEL_VCC
HD_60Hz_SMALL
LVDS 33
L7902
120-ohm
HD_60Hz_SMALL
HD_60Hz_SMALL
C7906
0.1uF
16V
Ver. 1.0
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only

JK9800
PPJ238-01
6C [RD1]E-LUG
5C [RD1]O-SPRING
4C [RD1]CONTACT
5B [WH1]O-SPRING
4A [YL1]CONTACT
5A [YL1]O-SPRING
6A [YL1]E-LUG
6H [RD2]E-LUG
5H [RD2]O-SPRING_2
4H [RD2]CONTACT
5G [WH2]O-SPRING
5F [RD2]O-SPRING_1
7F [RD2]E-LUG-S
5E [BL2]O-SPRING
7E [BL2]E-LUG-S
4D [GN2]CONTACT
5D [GN2]O-SPRING
6D [GN2]E-LUG
GAS2
MDS62110204
OPT
GAS1
MDS62110204
OPT
PLACE UNDER TUNER
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
GAS3
MDS62110204
OPT
D9800
5.6V
+3.3V_Normal
SIGN4272
R9802
10K
C9800
100pF
50V
OPT
R9800
10K
D9801
5.6V
AV_CVBS_DET
+3.3V_Normal
SMALL_US_KR_EM_JACK PACK_HONGSU_090818
R9803
1K
R9801
1K
COMP2_DET
D9806
5.6V
D9805
5.6V
D9803
30V
D9802
30V
D9807
5.6V
D9809
30V
D9808
5.6V
D9804
30V
SC1_CVBS_IN
R9806
0
R9805
0
R9804
0
TP9801
TP9802
TP9803
TP9804
TP9805
TP9806
TP9807
TP9808
TP9809
R9810
470K
R9813
470K
R9812
75
R9811
470K
R9807
75
R9809
75
R9808
75
R9814
470K
SC1_FB
SC1_ID
SC_RE1
SC_RE2
R9815
SIGN4271 10K
C9805
1000pF
50V
R9816
10K
R9817
SIGN426910K
R9818
SIGN427010K
C9808
1000pF
50V
C9803
10pF
OPT
50V
OPT
C9801
10pF
50V
SCART1_MUTE
SC1_SOG_IN
SCART1_Lout
SCART1_Rout
DTV/MNT_VOUT
C9806
1000pF
50V
OPT
C9807
10pF
50V
C9804
1000pF
50V
C9802
10pF OPT
50V
R9820
12K
SCART OPTION BLOCK
R9821
12K
R9819
12K
R9822
12K
AV_R_IN
AV_L_IN
AV_CVBS_IN
COMP2_R_IN
COMP2_L_IN
COMP2_Pr+
COMP2_Pr-
COMP2_Pb+
COMP2_Pb-
COMP2_Y+
COMP2_Y-
Component2 OPTION BLOCK
TP9810
TP9811
TP9812
TP9813
TP9814
TP9815
TP9816
TP9817
TP9818
US_REAR_COMP_AV_SMALL
SC1_R+/COMP1_Pr+
SC1_R-/COMP1_Pr-
SC1_G+/COMP1_Y+
SC1_G-/COMP1_Y-
SC1_B+/COMP1_Pb+
SC1_B-/COMP1_Pb-
SC1/COMP1_L_IN
SC1/COMP1_R_IN
SC1/COMP1_DET
GP2_Saturn7M Ver. 1.0
Copyright © 2010 LG Electronics. Inc. All rights reserved.
Only for training and service purposes LGE Internal Use Only
98