CANopen Programmer's Manual - Maccon.de

More documents

Recommendations

Info

APPENDIX A: ALTERNATIVE CONTROL SOURCES This chapter describes control of an amplifier by a source other than the CANopen network. Contents include: A.1: Alternative Control Sources Overview ................................................................................................ 225 A.2: Alternative Control Source Objects .................................................................................................... 226 A.3: Running CAM Tables from RAM ........................................................................................................ 231 Copley Controls 224
CANopen Programmer’s Manual A: Alternative Control Sources A.1: Alternative Control Sources Overview Typically, when a Copley amplifier is used on a CANopen network, the CANopen master uses the network to send commands that drive the amplifier’s position, velocity, or current loop. Alternately, an amplifier on a CANopen network can accept position, velocity, or current commands over the device’s serial port, digital I/O channels, or analog reference inputs, or run under the control of the amplifier’s internal generator or a Copley Virtual Machine (CVM) program. Use the Indexer Register Values object (index 0x2600, p. 231) to read and write the CVM Indexer program registers. An amplifier can also run in camming mode to execute moves programmed in camming tables. The Camming Configuration object (index 0x2360, p. 229) and several other objects described in this chapter are used to configure and operate the amplifier in camming mode. Even while operating under an alternative control source, a device’s status can still be monitored over the CANopen network. Specify a control source by choosing a mode in the Desired State object (index 0x2300). For more information, see page 65. Other objects affect the amplifier under alternative control sources. They are described in the next section. Copley Controls 225
Page 1:
CANopen Programmer’s Manual Part
Page 5 and 6:
CANopen Programmer’s Manual Table
Page 7 and 8:
About this Manual CANopen Programme
Page 9 and 10:
About this Manual CANopen Programme
Page 11 and 12:
CHAPTER 1: INTRODUCTION This chapte
Page 13 and 14:
CANopen Programmer’s Manual 1: In
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
CHAPTER 2: NETWORK MANAGEMENT This
Page 41 and 42:
CANopen Programmer’s Manual 2: Ne
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
CHAPTER 3: DEVICE CONTROL, CONFIGUR
Page 53 and 54:
CANopen Programmer’s Manual 3: De
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
CHAPTER 4: CONTROL LOOP CONFIGURATI
Page 129 and 130:
CANopen Programmer’s Manual 4: Co
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
CANopen Programmer’s Manual 5: St
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
CANopen Programmer’s Manual 6: Ho
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174: CANopen Programmer’s Manual 6: Ho
Page 191 and 192: CANopen Programmer’s Manual 7: Pr
Page 207 and 208: CANopen Programmer’s Manual 9: Cy
Page 223: CANopen Programmer’s Manual 9: Cy
Page 227 and 228: CANopen Programmer’s Manual A: Al
Page 237 and 238: CANopen Programmer’s Manual B: Tr
Page 245 and 246: CANopen Programmer’s Manual C: Ob
Page 257: CANopen Programmer’s Manual P/N 9
show all

CANopen Programmer's Manual - Maccon.de

Create successful ePaper yourself

Delete template?

Save as template?