CANopen Programmer's Manual - Maccon.de

More documents

Recommendations

Info

9: Cyclic Synchronous Modes CANopen Programmer’s Manual TRAJECTORY BUFFER STATUS INDEX 0X2012 Type Access Units Range Map PDO Memory Unsigned 32 RO - See Description, below. EVENT - Description This object gives access to status information about the IP trajectory buffer. The status value is bit-mapped as follows: Bit(s) Description 0-15 These bits hold the 16-bit segment identifier of the next IP move segment expected. If a segment error has occurred (i.e. the segment integrity counter of a received message was out of order), then these bits may be consulted to determine the ID of the segment that should have been received. 16-23 The number of free locations in the IP buffer. 24 Set if a segment sequence error is in effect. A segment sequence error occurs when an IP segment is received with the incorrect value in its integrity counter. 25 Set if a buffer overflow has occurred. 26 Set if a buffer underflow has occurred. 27-30 Reserved for future use. 31 This bit is set if the IP buffer is empty. This object is intended to be read using a PDO, and has a PDO event associated with it. The event occurs when one of the error bits (24 – 26) is set, or when the trajectory generator removes a segment from the trajectory buffer. NEXT TRAJECTORY SEGMENT ID INDEX 0X2013 Type Access Units Range Map PDO Memory Unsigned 16 RO - - YES R Description This object gives the full 16-bit value of the next trajectory segment expected by the buffer interface. It contains the same information as bits 0-15 of the Trajectory Buffer Status object (index 0x2012). INTERPOLATION SUBMODE SELECT INDEX 0X60C0 Type Access Units Range Map PDO Memory Integer 16 RW - - YES R Description Determines which interpolation submode to use: Submode Description 0 Linear interpolation with a constant time. -1 Linear interpolation with variable time. -2 Cubic polynomial interpolation, which is also known as position, velocity, and time (PVT) interpolation. NOTE: Copley Controls provides a set of alternate objects (0x 2010, 0x 2011, 0x 2012, and 0x 2013) for efficient PVT move handling. When using the alternate objects, it is not necessary to set a linear interpolation submode using Interpolation Submode Select. 216 Copley Controls
CANopen Programmer’s Manual 9: Cyclic Synchronous Modes INTERPOLATION DATA RECORD INDEX 0X60C1 Type Access Units Range Map PDO Memory Record RW - - YES R Description This object is used to send interpolation data to the amplifier’s interpolation buffer. INTERPOLATION POSITION TARGET INDEX 0X60C1, SUB-INDEX 1 Type Access Units Range Map PDO Memory Integer 32 RW Counts - YES R Description A target position. Used in all three interpolation modes. INTERPOLATION TIME INDEX 0X60C1, SUB-INDEX 2 Type Access Units Range Map PDO Memory Unsigned 8 RW milliseconds - YES R Description The time interval of the move segment that starts with the Interpolation Position Target (Sub-Index 1), and extends to the next segment. Not used with interpolation mode 0 (linear interpolation with a constant time). In interpolation mode -1 (linear interpolation with variable time), writing to this object causes the entire record to be written to the interpolation buffer. Writing a value of zero to this object indicates the end of the interpolated move. INTERPOLATION VELOCITY INDEX 0X60C1, SUB-INDEX 3 Type Access Units Range Map PDO Memory Integer 32 RW 0.1 counts/sec - YES R Description Used only in interpolation mode -2 (PVT). This is the velocity used to drive the axis to the Interpolation Position Target (Sub-Index 1) within the Interpolation Time (Sub-Index 2). Writing to this object causes the entire record to be written to the interpolation buffer. Copley Controls 217
Page 1:
CANopen Programmer’s Manual Part
Page 5 and 6:
CANopen Programmer’s Manual Table
Page 7 and 8:
About this Manual CANopen Programme
Page 9 and 10:
About this Manual CANopen Programme
Page 11 and 12:
CHAPTER 1: INTRODUCTION This chapte
Page 13 and 14:
CANopen Programmer’s Manual 1: In
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
CHAPTER 2: NETWORK MANAGEMENT This
Page 41 and 42:
CANopen Programmer’s Manual 2: Ne
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
CHAPTER 3: DEVICE CONTROL, CONFIGUR
Page 53 and 54:
CANopen Programmer’s Manual 3: De
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
CHAPTER 4: CONTROL LOOP CONFIGURATI
Page 129 and 130:
CANopen Programmer’s Manual 4: Co
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
CANopen Programmer’s Manual 5: St
Page 161 and 162:
Page 163 and 164:
Page 165 and 166: CANopen Programmer’s Manual 6: Ho
Page 191 and 192: CANopen Programmer’s Manual 7: Pr
Page 207 and 208: CANopen Programmer’s Manual 9: Cy
Page 215: CANopen Programmer’s Manual 9: Cy
Page 225 and 226: CANopen Programmer’s Manual A: Al
Page 237 and 238: CANopen Programmer’s Manual B: Tr
Page 245 and 246: CANopen Programmer’s Manual C: Ob
Page 257: CANopen Programmer’s Manual P/N 9
show all

CANopen Programmer's Manual - Maccon.de

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?