WinEMP - NRI
WinEMP - NRI WinEMP - NRI
National Rejectors, Inc. GmbH, Buxtehude STARTING UP • Connect the card reader with the serial interface of the PC (COM1/ COM2) using the enclosed connecting cable via the interface labelled ”PC connector”. • Plug the connecting plug of the power pack into the socket ”9 V DC” of the card reader. Only use the 9 V power pack enclosed in delivery! • Now connect the tester and the power pack with the mains supply. The power LED on the card reader should be green. • Switch the tester on at the mains switch (for operation and function of the tester please refer to the operating instructions ”Tester G-19.0594/4“). To program the coin validator G-18 battery, it must be set to permanent wake-up mode using the tester (WE diode is on). • Please make sure that the DIL switches of the coin validator are in the required positions (see sticker on the rear of the coin validator and also refer to separate instructions for the coin validator). • Insert your chip card in the direction of the arrow into the slot on the card reader labelled ”Chip Card”. Install WinEMP If you want WinEMP only to display the data of the diagnostics screen, the chip card does not have to be inserted in the card reader. The chip card does need to be inserted in the card reader to program the data. The NRI Euro, adjusting and diagnostics program WinEMP is supplied on a CD-ROM. Please proceed as follows to install the program from the CD-ROM: • Close all open programs on your PC. • Open Windows Explorer and start the installation file ”WinEMP.exe” in the CD-ROM drive by double-clicking on it. • To install the program, please follow the instructions on the screen. • After successfully installing the program, please re-start your computer. The program has been stored on the hard disc of your PC and the WinEMP icon has been saved in your PC desktop so you can start the program easily. 8
National Rejectors, Inc. GmbH, Buxtehude STARTING UP Start WinEMP The program can be opened either by double-clicking on the WinEMP icon on the PC desktop or by double-clicking on the WinEMP.exe file, installed on the hard disc of your PC, Windows Explorer. After a loading window has been displayed for a brief time (Checking for validator – please wait, Validator found – Reading data) the main menu (diagnostics screen) is displayed – if the device environment has been correctly installed as described above. The card LED on the card reader is red as long as the software accesses the card which has been inserted in the device. As long as the card LED is red, the card must not be pulled out or pushed in. This can cause the card to be destroyed! If, after a short time, the error message ”Validator not found – please check connections” is displayed, either the device environment has not been connected or the connections/cables are faulty (see chapter 4 ”Error messages”). 9
- Page 1 and 2: Technical documentation WinEMP The
- Page 3 and 4: National Rejectors, Inc. GmbH, Buxt
- Page 5 and 6: National Rejectors, Inc. GmbH, Buxt
- Page 7: National Rejectors, Inc. GmbH, Buxt
- Page 11 and 12: National Rejectors, Inc. GmbH, Buxt
- Page 13 and 14: National Rejectors, Inc. GmbH, Buxt
- Page 15 and 16: National Rejectors, Inc. GmbH, Buxt
- Page 17 and 18: National Rejectors, Inc. GmbH, Buxt
- Page 19 and 20: National Rejectors, Inc. GmbH, Buxt
- Page 21 and 22: National Rejectors, Inc. GmbH, Buxt
- Page 23 and 24: National Rejectors, Inc. GmbH, Buxt
- Page 25 and 26: National Rejectors, Inc. GmbH, Buxt
- Page 27 and 28: National Rejectors, Inc. GmbH, Buxt
- Page 29 and 30: National Rejectors, Inc. GmbH, Buxt
- Page 31 and 32: National Rejectors, Inc. GmbH, Buxt
- Page 33 and 34: National Rejectors, Inc. GmbH, Buxt
- Page 35 and 36: National Rejectors, Inc. GmbH, Buxt
- Page 37 and 38: National Rejectors, Inc. GmbH, Buxt
- Page 39 and 40: National Rejectors, Inc. GmbH, Buxt
- Page 41 and 42: G-18.2900 Hardware adaptation withi
- Page 43: WinEMP Reference list for data bloc
National Rejectors, Inc. GmbH, Buxtehude STARTING UP<br />
Start <strong>WinEMP</strong><br />
The program can be opened either by double-clicking on the <strong>WinEMP</strong> icon<br />
on the PC desktop or by double-clicking on the <strong>WinEMP</strong>.exe file,<br />
installed on the hard disc of your PC, Windows Explorer.<br />
After a loading window has been<br />
displayed for a brief time (Checking<br />
for validator – please wait,<br />
Validator found – Reading<br />
data) the main menu (diagnostics<br />
screen) is displayed – if the device<br />
environment has been correctly installed<br />
as described above.<br />
The card LED on the card reader is red as long as the software accesses the<br />
card which has been inserted in the device.<br />
As long as the card LED is red, the card must not be pulled out or<br />
pushed in. This can cause the card to be destroyed!<br />
If, after a short time, the error message ”Validator not found –<br />
please check connections” is displayed, either the device<br />
environment has not been connected or the connections/cables are<br />
faulty (see chapter 4 ”Error messages”).<br />
9
Change language