WinEMP - NRI

More documents

Recommendations

Info

CONFIGURATION – FOR MDB/S1 INTERFACE Configure G-13.mft for MDB/S1 operation 92 WinEMP – G-13.mft This section describes all the possible settings for the MDB model and S1 model of the G-13.mft. You find how to perform settings for • coin type and coin value, • acceptance gate, • coin inhibit, • teach mode and • coin sorting. Store changes in coin validator and return to main menu Copy, insert, and delete channel data; name coin Simulation for inhibiting via DIL switches Assign sorting control line Assign DIL switch (inhibit) Configure channelsuperordinate data: smallest coin value/coin values, attraction time of acceptance gate, teach mode, sorting Assign coin value Configure channel-specific data Deactivate using coin validator software National Rejectors, Inc. GmbH, Buxtehude
WinEMP – G-13.mft CONFIGURATION – FOR MDB/S1 INTERFACE Configure the smallest coin value as a basis of calculation for coin values For the coin validator, the smallest coin value is the reference value for datamanaging all programmed coin values. The values of all the coin types accepted by the coin validator must be integral multiples of the smallest coin value. National Rejectors, Inc. GmbH, Buxtehude If the smallest coin value is changed, the coin values of the channels may also have to be changed accordingly! WinEMP will mark these coin values in red for you. For changing the values, please simply follow the queries automatically generated by WinEMP (see also section "Configure coin value/ token identification" in this chapter). When you have taught a new coin in a coin channel which is smaller than the smallest coin value configured so far, that value must be set as a basis of calculation for the coin validator: 1 Select menu item EXTRA and then BASIC SETTINGS. The dialog box BASIC SETTINGS AND OPTIONS opens. 2 In the "table of contents" on the left-hand side, select the index word SMALLEST COIN VALUE (for S1 devices COIN VALUES). 3 On the righthand side enter the desired SMALLEST COIN VALUE using the keyboard. 4 Confirm your entry with OK and close the window again or proceed to the next setting in this dialog box first and confirm all your settings later. 5 Click BACK to store the setting in the G-13.mft or proceed to the next setting on this screen and store all your settings later. 93
Page 1:
Technical Documentation The configu
Page 4 and 5:
TABLE OF CONTENTS 4 WinEMP - G-13.m
Page 6 and 7:
TABLE OF CONTENTS 6 WinEMP - G-13.m
Page 9 and 10:
WinEMP - G-13.mft GENERAL INFORMATI
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
WinEMP - G-13.mft 3 Installation In
Page 17 and 18:
WinEMP - G-13.mft INSTALLATION 7 Pl
Page 19 and 20:
WinEMP - G-13.mft Start WinEMP Nati
Page 21 and 22:
WinEMP - G-13.mft National Rejector
Page 23 and 24:
WinEMP - G-13.mft General operating
Page 25 and 26:
WinEMP - G-13.mft GENERAL PROGRAM S
Page 27 and 28:
Page 29 and 30:
WinEMP - G-13.mft Perform tests Nat
Page 31 and 32:
WinEMP - G-13.mft Select memory blo
Page 33 and 34:
Page 35 and 36:
WinEMP - G-13.mft 8 Configuration N
Page 37 and 38:
WinEMP - G-13.mft G-13.mft with MDB
Page 39 and 40:
Page 41 and 42: WinEMP - G-13.mft National Rejector
Page 43 and 44: WinEMP - G-13.mft Teach coin types/
Page 47 and 48: WinEMP - G-13.mft CONFIGURATION - F
Page 91: WinEMP - G-13.mft CONFIGURATION - F
Page 115 and 116: WinEMP - G-13.mft Copy and paste or
Page 117 and 118: WinEMP - G-13.mft Change token/coin
Page 129 and 130: WinEMP - G-13.mft After the data bl
Page 133 and 134: WinEMP - G-13.mft 10 Restore G-13.m
Page 135 and 136: WinEMP - G-13.mft WINEMP UPDATE 12
Page 137 and 138: National Rejectors, Inc. GmbH, Buxt
Page 143 and 144:
National Rejectors, Inc. GmbH, Buxt
Page 145 and 146:
National Rejectors, Inc. GmbH, Buxt
Page 147 and 148:
WinEMP - G-13.mft C Card reader 10
Page 149 and 150:
WinEMP - G-13.mft E ECV 155 totaliz
Page 151 and 152:
WinEMP - G-13.mft Return signal lin
Page 153 and 154:
WinEMP - G-13.mft Glossary National
Page 155 and 156:
Page 157 and 158:
show all

WinEMP - NRI

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?