WinEMP - NRI

More documents

Recommendations

Info

PREPARATION 28 WinEMP – G-13.mft The right-hand column of the screen provides information about the status of the most important functions of the G-13.mft: • OPERATING VOLTAGE • Status of the RETURN SIGNAL: INACTIVE (no signal)/ ACTIVE (signal, when return lever is pressed) • Status of the COMMON INHIBIT SIGNAL (only parallel interface): INACTIVE (no signal)/ ACTIVE (signal from tester/vending machine) • Status of the external INDIVIDUAL INHIBIT SIGNALS (only parallel validator operation): _ = not inhibited by tester/vending machine DIGIT of the line = inhibited by tester/vending machine • Number of coin CHANNEL, which accepted the coin inserted LAST • Status/functionality of accepted coin sensors (CP3/CP4 SIGNAL): INACTIVE – Sensor in the standby state and not covered ACTIVE – Sensor covered e.g. by coin pile-up or faulty (remove objects in front of the sensor or have the sensor replaced by the service technician) • PRICES set using switching blocks on the rear of the G-13.mft (only 1-/ 2-price totalizer operation) • TIMER period and corresponding price set using switching blocks on the rear of the G-13.mft (only timer operation) • Price set for one game and BONUS levels set using switching blocks on the rear of the G-13.mft (only TV totalizer operation) • DIL SWITCH positions of the switching blocks on the rear of the G-13.mft: _ = OFF/DIGIT = ON (Please refer to separate G-13.mft instructions for function of the DIL switches) • Status/functionality of light barriers (LS1/LS2 SENSOR): OK – Sensor in the standby state and not covered ERR – Sensor covered, e.g., by coin pile-up or defective (remove objects in front of the sensor or have the sensor replaced by a service technician) • ERROR MESSAGE (for error remedy see Chap. 13 "Status and error massages") WinEMP registers any state changes (e.g. caused by coin insertion or switching a DIL switch) and displays these changes on the screen so that you can then test the above-mentioned functions of the coin validator. National Rejectors, Inc. GmbH, Buxtehude
WinEMP – G-13.mft Perform tests National Rejectors, Inc. GmbH, Buxtehude PREPARATION Two basic requirements for the functionality of the G-13.mft are reliable signal lines between the machine (tester) and the G-13.mft as well as a perfectly functioning acceptance gate. WinEMP enables you to test these equipment parts. Test signal lines (only for parallel interface) Signal lines can only be checked, if the coin validator is supplied with power by the NRI testers G-19.0594/G-19.0651 or G-19.0645/ G-19.0650. To test the external inhibit signal lines between the vending machine (tester) and the G-13.mft in validator operation or the reset and common inhibit signal line between the vending machine (tester) and the G-13.mft in totalizer operation, select menu item TESTS in the main menu and then LINE TEST. While the status display is displaying the message LINES ARE BEING CHECKED – PLEASE WAIT, the function of the external signal lines is checked automatically. On the tester, the LEDs assigned to the signal lines light up briefly. If an LED does not light up, either the connection between the G-13.mft and the vending machine (tester) is defective (cable, plug-in connections) or a coin validator component is defective. In this case, please contact the service technician. Test acceptance gate To test the acceptance gate of the G-13.mft, please select menu item TESTS in the main menu and then GATE TEST. While the status display is displaying the message GATES ARE BEING CHECKED – PLEASE WAIT, the function of the acceptance gate is checked automatically. You can hear the solenoid being activated and released again. If you can’t hear a noise, the module must be checked. 29
Page 1: Technical Documentation The configu
Page 4 and 5: TABLE OF CONTENTS 4 WinEMP - G-13.m
Page 6 and 7: TABLE OF CONTENTS 6 WinEMP - G-13.m
Page 9 and 10: WinEMP - G-13.mft GENERAL INFORMATI
Page 15 and 16: WinEMP - G-13.mft 3 Installation In
Page 17 and 18: WinEMP - G-13.mft INSTALLATION 7 Pl
Page 19 and 20: WinEMP - G-13.mft Start WinEMP Nati
Page 21 and 22: WinEMP - G-13.mft National Rejector
Page 23 and 24: WinEMP - G-13.mft General operating
Page 25 and 26: WinEMP - G-13.mft GENERAL PROGRAM S
Page 27: WinEMP - G-13.mft National Rejector
Page 31 and 32: WinEMP - G-13.mft Select memory blo
Page 35 and 36: WinEMP - G-13.mft 8 Configuration N
Page 37 and 38: WinEMP - G-13.mft G-13.mft with MDB
Page 43 and 44: WinEMP - G-13.mft Teach coin types/
Page 47 and 48: WinEMP - G-13.mft CONFIGURATION - F
Page 79 and 80:
WinEMP - G-13.mft CONFIGURATION - F
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
WinEMP - G-13.mft Copy and paste or
Page 117 and 118:
WinEMP - G-13.mft Change token/coin
Page 119 and 120:
WinEMP - G-13.mft National Rejector
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
WinEMP - G-13.mft After the data bl
Page 131 and 132:
Page 133 and 134:
WinEMP - G-13.mft 10 Restore G-13.m
Page 135 and 136:
WinEMP - G-13.mft WINEMP UPDATE 12
Page 137 and 138:
National Rejectors, Inc. GmbH, Buxt
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
WinEMP - G-13.mft C Card reader 10
Page 149 and 150:
WinEMP - G-13.mft E ECV 155 totaliz
Page 151 and 152:
WinEMP - G-13.mft Return signal lin
Page 153 and 154:
WinEMP - G-13.mft Glossary National
Page 155 and 156:
Page 157 and 158:
show all

WinEMP - NRI

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?