WinEMP - NRI

More documents

Recommendations

Info

PREPARATION 6 Preparation 26 <strong>WinEMP</strong> – G-13.mft This chapter describes all those tasks which should be performed before the coin validator data is actually set: • Check device data and functionality • Test signal lines (for parallel interface only) • Test acceptance gate • Display licences of the chip card • Select memory block for configuration (only with double block datamanagement) Check device data and functionality The main menu, which you will access automatically after starting up the program, enables you to check the perfect working order of the device before configuring the G-13.mft using the presented basic and I/O data. National Rejectors, Inc. GmbH, Buxtehude
<strong>WinEMP</strong> – G-13.mft National Rejectors, Inc. GmbH, Buxtehude PREPARATION The left column displays the device data for the connected G-13.mft: • ORDER NUMBER/DEVICE NUMBER/ORDERING CODE (compare label of coin validator) • Date of programming of all default values (DATE OF MANUFACTURE) • Date of last change to the coin validator data (DATE OF LAST ADJUSTMENT) With double block data-management, the upper date applies to memory block 0, and the lower date applies to memory block 1. If both memory blocks were programmed or changed on the same day, only one date is displayed (as shown). • 8-digit number of the current DATA BLOCK in the device memory and its 3-digit REVISION NUMBER (update number of this data block) (compare label of coin validator) • SOFTWARE VERSION of the G-13.mft • Status of the CHECKSUMS (RAM or EEPROM) (OK/ERR) If one of the checksums is defective (display = ERR), the coin validator will not accept any coins. The device must then be checked by a service technician and repaired if necessary. 27
Page 1: Technical Documentation The configu
Page 4 and 5: TABLE OF CONTENTS 4 WinEMP - G-13.m
Page 6 and 7: TABLE OF CONTENTS 6 WinEMP - G-13.m
Page 9 and 10: WinEMP - G-13.mft GENERAL INFORMATI
Page 15 and 16: WinEMP - G-13.mft 3 Installation In
Page 17 and 18: WinEMP - G-13.mft INSTALLATION 7 Pl
Page 19 and 20: WinEMP - G-13.mft Start WinEMP Nati
Page 21 and 22: WinEMP - G-13.mft National Rejector
Page 23 and 24: WinEMP - G-13.mft General operating
Page 25: WinEMP - G-13.mft GENERAL PROGRAM S
Page 29 and 30: WinEMP - G-13.mft Perform tests Nat
Page 31 and 32: WinEMP - G-13.mft Select memory blo
Page 35 and 36: WinEMP - G-13.mft 8 Configuration N
Page 37 and 38: WinEMP - G-13.mft G-13.mft with MDB
Page 43 and 44: WinEMP - G-13.mft Teach coin types/
Page 47 and 48: WinEMP - G-13.mft CONFIGURATION - F
Page 77 and 78:
WinEMP - G-13.mft CONFIGURATION - F
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
WinEMP - G-13.mft Copy and paste or
Page 117 and 118:
WinEMP - G-13.mft Change token/coin
Page 119 and 120:
WinEMP - G-13.mft National Rejector
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
WinEMP - G-13.mft After the data bl
Page 131 and 132:
Page 133 and 134:
WinEMP - G-13.mft 10 Restore G-13.m
Page 135 and 136:
WinEMP - G-13.mft WINEMP UPDATE 12
Page 137 and 138:
National Rejectors, Inc. GmbH, Buxt
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
WinEMP - G-13.mft C Card reader 10
Page 149 and 150:
WinEMP - G-13.mft E ECV 155 totaliz
Page 151 and 152:
WinEMP - G-13.mft Return signal lin
Page 153 and 154:
WinEMP - G-13.mft Glossary National
Page 155 and 156:
Page 157 and 158:
show all

WinEMP - NRI

Create successful ePaper yourself

Delete template?

Save as template?