WinEMP - NRI

More documents

Recommendations

Info

WinEMP – G-13.mft MENU STRUCTURE AND GENERAL FUNCTIONS Main menu Function Navigation Menu Select menu language EXTRA → LANGUAGE Select screen colour EXTRA → COLORS Check device data Test signal lines TESTS → LINE TEST Test acceptance gate TESTS → GATE TEST Select memory block for configuration TESTS → SELECT BLOCK Screen "Settings" SETTINGS → EDIT Duplicate settings for series configuration SETTINGS → DUPLICATE Select operating mode SETTINGS → DEVICE VARIANT Load new data block into G-13.mft DOWNLOAD → DATA BLOCK Restore old coin validator settings RESTORE Software and chip card properties INFO Exit program EXIT "Settings" Compare measured coin values with channel values Adjust coin acceptance INSERT COINS → GENUINE/ FALSE COINS Teach new coin type INSERT COINS → TEACH NEW COINS Configure basic settings EXTRA→ BASIC SETTINGS Configure optional functions EXTRA → OPTIONS Copy coin channel data CHANNEL → COPY Insert CHANNEL → PASTE Delete (also all channels) CHANNEL → CLEAR (ALL) Save settings and return BACK to the main menu National Rejectors, Inc. GmbH, Buxtehude 22
WinEMP – G-13.mft General operating functions National Rejectors, Inc. GmbH, Buxtehude MENU STRUCTURE AND GENERAL FUNCTIONS In this section simple functions are to be explained once. These functions will not be mentioned again for the adjustment steps included in the following chapters. • The top program line shows the WinEMP version, the connected device and the activated memory block 0 or 1 (if available). • By clicking the menu item BACK you will always go – possibly after confirming/rejecting the query WRITE DATA INTO VALIDATOR? – back to the main menu. • The program can only be exited from the main menu. • Coin validator data that has been changed is written into the connected device before the user leaves the screen "Settings" via the menu item BACK and after the query WRITE DATA INTO VALIDATOR? • Each configuration stored in the device can be restored using an archive. The basic requirement for this option is that the device must always be configured on the same PC, since the archive files are stored on the hard disk of the PC. • Faulty input is displayed in red or an acoustic signal is sounded. Before the screen "Settings" is exited, the warning ENTRIES NOT CORRECT. IGNORE CHANGES? IS DISPLAYED. • Any settings WinEMP cannot read or which are faulty are identified by a question mark in the appropriate input field. • Using the menu item INFO, in the top right-hand side of the main menu, an info box with the WinEMP software version and access rights will always be displayed. You can close the window by clicking OK. • Using the button ABORT the user aborts a process and leaves the respective pop-up window. • Underlined letters in the menu bar and in the pull-down menus must be treated the same way as in Windows and stand for the key that executes specific functions when pressed before or together with the "Alt" key. • When selecting the functions using the main menu bar, the access rights of the user are checked. An info box is displayed. • Loading and testing operations are always documented in an info box by means of a status-bar indicator. 23
Page 1: Technical Documentation The configu
Page 4 and 5: TABLE OF CONTENTS 4 WinEMP - G-13.m
Page 6 and 7: TABLE OF CONTENTS 6 WinEMP - G-13.m
Page 9 and 10: WinEMP - G-13.mft GENERAL INFORMATI
Page 15 and 16: WinEMP - G-13.mft 3 Installation In
Page 17 and 18: WinEMP - G-13.mft INSTALLATION 7 Pl
Page 19 and 20: WinEMP - G-13.mft Start WinEMP Nati
Page 21: WinEMP - G-13.mft National Rejector
Page 25 and 26: WinEMP - G-13.mft GENERAL PROGRAM S
Page 27 and 28: WinEMP - G-13.mft National Rejector
Page 29 and 30: WinEMP - G-13.mft Perform tests Nat
Page 31 and 32: WinEMP - G-13.mft Select memory blo
Page 35 and 36: WinEMP - G-13.mft 8 Configuration N
Page 37 and 38: WinEMP - G-13.mft G-13.mft with MDB
Page 43 and 44: WinEMP - G-13.mft Teach coin types/
Page 47 and 48: WinEMP - G-13.mft CONFIGURATION - F
Page 73 and 74:
WinEMP - G-13.mft CONFIGURATION - F
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
WinEMP - G-13.mft Copy and paste or
Page 117 and 118:
WinEMP - G-13.mft Change token/coin
Page 119 and 120:
WinEMP - G-13.mft National Rejector
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
WinEMP - G-13.mft After the data bl
Page 131 and 132:
Page 133 and 134:
WinEMP - G-13.mft 10 Restore G-13.m
Page 135 and 136:
WinEMP - G-13.mft WINEMP UPDATE 12
Page 137 and 138:
National Rejectors, Inc. GmbH, Buxt
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
WinEMP - G-13.mft C Card reader 10
Page 149 and 150:
WinEMP - G-13.mft E ECV 155 totaliz
Page 151 and 152:
WinEMP - G-13.mft Return signal lin
Page 153 and 154:
WinEMP - G-13.mft Glossary National
Page 155 and 156:
Page 157 and 158:
show all

WinEMP - NRI

Create successful ePaper yourself

Delete template?

Save as template?